Media Access Control

The Media Access Control (MAC) data communication protocol sub-layer, also known as the Medium Access Control, is a sublayer of the Data Link Layer specified in the seven-layer OSI model (layer 2). It provides addressing and channel access control mechanisms that make it possible for several terminals or network nodes to communicate within a multi-point network, typically a local area network (LAN) or metropolitan area network (MAN). The hardware that implements the MAC is referred to as a Medium Access Controller.

The MAC sub-layer acts as an interface between the Logical Link Control (LLC) sublayer and the network's physical layer. The MAC layer emulates a full-duplex logical communication channel in a multi-point network. This channel may provide unicast, multicast or broadcast communication service.

 

Addressing mechanism

The MAC layer addressing mechanism is called physical address or MAC address. A MAC address is a unique serial number. Once a MAC address has been assigned to a particular piece of network hardware (at time of manufacture), that device should be uniquely identifiable amongst all other network devices in the world. This guarantees that each device in a network will have a different MAC address (analogous to a street address). This makes it possible for data packets to be delivered to a destination within a subnetwork, i.e. a physical network consisting of several network segments interconnected by repeaters, hubs, bridges and switches, but not by IP routers. An IP router may interconnect several subnets.

An example of a physical network is an Ethernet network, perhaps extended by wireless local area network (WLAN) access points and WLAN network adapters, since these share the same 48-bit MAC address hierarchy as Ethernet.

A MAC layer is not required in full-duplex point-to-point communication, but address fields are included in some point-to-point protocols for compatibility reasons.

 

Conclusion

1 链路层的所应用的协议决定了网络层是否支持广播、组播、单播

2 IP包的Layer3 的逻辑地址要被映射到Layer 2的物理地址进行物理层的传输

3 物理层上连接在同一传输介质（transmission media）上的网络设备可以直接通信，而跨越这个传输介质通信则需要第三层提供的地址

 

OSI Model
7 Application Layer
6 Presentation Layer
5 Session Layer
4 Transport Layer
3 Network Layer
2 Data Link Layer
LLC sublayer
MAC sublayer

1 Physical Layer

 

Data Link Layer

The Data Link Layer is Layer 2 of the seven-layer OSI model of computer networking. It corresponds to, or is part of the link layer of the TCP/IP reference model.

 

The Data Link Layer is the protocol layer which transfers data between adjacent network nodes in a wide area network or between nodes on the same local area network segment[1]. The Data Link Layer provides the functional and procedural means to transfer data between network entities and might provide the means to detect and possibly correct errors that may occur in the Physical Layer. Examples of data link protocols are Ethernet for local area networks (multi-node), the Point-to-Point Protocol (PPP), HDLC and ADCCP for point-to-point (dual-node) connections.

The Data Link Layer is concerned with local delivery of frames between devices on the same LAN. Data Link frames, as these protocol data units are called, do not cross the boundaries of a local network. Inter-network routing and global addressing are higher layer functions, allowing Data Link protocols to focus on local delivery, addressing, and media arbitration. In this way, the Data Link layer is analogous to a neighborhood traffic cop; it endeavors to arbitrate between parties contending for access to a medium.

 

When devices attempt to use a medium simultaneously, frame collisions occur. Data Link protocols specify how devices detect and recover from such collisions, and may provide mechanisms to reduce or prevent them.

Delivery of frames by layer 2 devices is affected through the use of unambiguous hardware addresses. A frame's header contains source and destination addresses that indicate which device originated the frame and which device is expected to receive and process it. In contrast to the hierarchical and routable addresses of the network layer, layer 2 addresses are flat, meaning that no part of the address can be used to identify the logical or physical group to which the address belongs.

The data link thus provides data transfer across the physical link. That transfer can be reliable or unreliable; many data link protocols do not have acknowledgments of successful frame reception and acceptance, and some data link protocols might not even have any form of checksum to check for transmission errors. In those cases, higher-level protocols must provide flow control, error checking, and acknowledgments and retransmission.

 

In some networks, such as IEEE 802 local area networks, the Data Link Layer is described in more detail with Media Access Control (MAC) and Logical Link Control (LLC) sublayers; this means that the IEEE 802.2 LLC protocol can be used with all of the IEEE 802 MAC layers, such as Ethernet, token ring, IEEE 802.11, etc., as well as with some non-802 MAC layers such as FDDI. Other Data Link Layer protocols, such as HDLC, are specified to include both sublayers, although some other protocols, such as Cisco HDLC, use HDLC's low-level framing as a MAC layer in combination with a different LLC layer. In the ITU-T G.hn standard, which provides a way to create a high-speed (up to 1 Gigabit/s) Local area network using existing home wiring (power lines, phone lines and coaxial cables), the Data Link Layer is divided into three sub-layers (Application Protocol Convergence, Logical Link Control and Medium Access Control).

 

Within the semantics of the OSI network architecture, the Data Link Layer protocols respond to service requests from the Network Layer and they perform their function by issuing service requests to the Physical Layer.