前言
Fast ping版本3.00是一款网络性能测试软件,用于代替windows附带的标准ping程序,可以控制设备之间发包的间隔、大小以及延时,查看丢包时间。文章结尾附上fping300永久下载链接
一、Fping300软件介绍
Fast ping版本3.00是一款网络性能测试软件,用于代替windows附带的标准ping程序,可以控制设备之间发包的间隔、大小以及延时,查看丢包时间。
二、使用限制
- windows可以直接在dos窗口直接使用;
- NT4 用户应该修改或添加注册表中变量并修改DWORD 1,然后重启;
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Afd\Parameters\DisableRawSecurity - 2000/XP用户应将以下注册表变量设置为DWORD 1,然后重启;
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Tcpip\Parameters\AllowUserRawAccess(也可以直接运行文件夹中的脚本文件Fping 2000_XP.reg和Fping NT.reg)
三、命令介绍
Options选项 | Introduction介绍 |
---|---|
-t | time between 2 pings in ms up to 1000000 两次ping之间的时间,以毫秒为单位,最高到1000000 |
-w | timeout in ms to wait for each reply 等待每个回复的超时(以毫秒为单位) |
-c | continuous ping (higher priority than -n) 连续ping(优先级高于-n) to see statistics and continue - type Control-B; 查看统计信息并继续-键入 Control-Bto stop - type Control-C.停止-键入Control-C。 |
-n | number of pings to send to each host 发送到每个主机的ping数 |
-s | amount of data in bytes up to 65500 数据量(以字节为单位),最多65500 |
-S | size sweep: ping with size1, size1 + 1, …, size2 bytes 大小扫描:ping为size1,size1 + 1,…,size2字节 |
-R | random length between min and max (disabled when using -S) 最小和最大之间的随机长度(使用-S时禁用) |
-d | ping with specified data 对指定数据执行ping操作 |
-h | number of hops (TTL: 1 to 128) + print hops 跳数(TTL:1至128)+打印跳数 |
-v | Type Of Service (0 to 255) (IPv4-only) 服务类型(0到255)(仅IPv4) |
-r | record route (1 to 9 routes) (IPv4-only) 记录路由(1到9条路由)(仅IPv4) |
-f | set Don’t Fragment flag in packet (IPv4-only) 设置数据包中的“不分段”标志(仅IPv4) |
-j | print jitter with each reply (only when pinging one host) 在每次回复时显示抖动(仅在ping一台主机时) |
-g | ping IP range from host1 to host2 (IPv4-only) ping从主机1到主机2的IP范围(仅IPv4) |
-H | get hosts from filename (comma delimited, filename with full path) 从文件名获取主机(逗号分隔,文件名带有完整路径) |
-a | resolve addresses to hostnames 将地址解析为主机名 |
-A | print addresses with each reply 打印每个回复的地址 |
-p | use a thread pool to ping multiple hosts (enables ICMP dll) 使用线程池对多个主机执行ping操作(启用ICMP dll) x is optional and allows you to choose the number of threads x是可选的,允许您选择线程数 e.g. -p uses a thread for every host,-p5 uses a pool of 5 threads/core 例如-p为每个主机使用一个线程,-p5使用5个线程/核心 |
-i | use ICMP dll instead of raw socket (disables -r) 使用ICMP dll而不是原始套接字(禁用-r) |
-b | beep on every successful reply (-b- to beep on timeout) 每次成功答复时发出蜂鸣声(-b-超时时发出蜂鸣声) |
-T | print timestamp with each reply 在每次回复时打印时间戳记 |
-D | print date stamp with each reply 在每个回复中打印日期戳 |
-l | limit the output to ping results and errors 将输出限制为ping结果和错误 |
-o | limit the output to ping statistics 将输出限制为ping统计信息 |
-L | logging to a text file 登录到文本文件 |
四、常用动调命令
fping 192.168.1.1 -s 185 -t 100 -c -w 100 -T -L test.txt
Fping | 调用fping |
---|---|
192.168.1.1 | Ping的目的主机 |
-s 185 | 185字节的数据量 |
-t 100 | 两次ping的时间间隔为100ms |
-c | 连续ping,使用查看统计信息并继续-键入Control-B,停止-键入Control-C。 |
-w 100 | 等待回复的超时100ms |
-T | 在每次回复时打上时间戳 |
-L test.txt | 根目录下保存的文本文件 |
该命令为网络性能测试时的常用命令
总结
以上就是fping300的内容,本文仅仅简单介绍了fping300的使用,用于简单的网络性能检测。
链接:https://pan.baidu.com/s/1uzWgC0frNci8kZEiHeZQEw
提取码:wg83
如有问题请及时回复