数字温度计

the_Mercury

已于 2023-11-25 19:46:59 修改

阅读量104

点赞数

文章标签：单片机 stm32 嵌入式硬件

于 2023-11-25 19:46:29 首次发布

本文链接：https://blog.csdn.net/the_mercury/article/details/134555246

版权

一.了解时钟RTC
RTC (Real Time Clock)：实时时钟

RTC是个独立的定时器。RTC模块拥有一个连续计数的计数器，在相应的软件配置下，可以提供时钟日历的功能。修改计数器的值可以重新设置当前时间和日期 RTC还包含用于管理低功耗模式的自动唤醒单元。

在断电情况下 RTC仍可以独立运行只要芯片的备用电源一直供电,RTC上的时间会一直走。

RTC实质是一个掉电后还继续运行的定时器,从定时器的角度来看,相对于通用定时器TIM外设,它的功能十分简单,只有计时功能(也可以触发中断)。但其高级指出也就在于掉电之后还可以正常运行。

两个 32 位寄存器包含二进码十进数格式 (BCD) 的秒、分钟、小时（ 12 或 24 小时制）、星期几、日期、月份和年份。此外，还可提供二进制格式的亚秒值。系统可以自动将月份的天数补偿为 28、29（闰年）、30 和 31 天。

上电复位后，所有RTC寄存器都会受到保护，以防止可能的非正常写访问。

无论器件状态如何（运行模式、低功耗模式或处于复位状态），只要电源电压保持在工作范围内，RTC使不会停止工作。

RCT特征：
● 可编程的预分频系数：分频系数高为220。
● 32位的可编程计数器，可用于较长时间段的测量。
● 2个分离的时钟：用于APB1接口的PCLK1和RTC时钟(RTC时钟的频率必须小于PCLK1时钟频率的四分之一以上)。
● 可以选择以下三种RTC的时钟源：
● HSE时钟除以128；
● LSE振荡器时钟；
● LSI振荡器时钟

● 2个独立的复位类型：
● APB1接口由系统复位；
● RTC核心(预分频器、闹钟、计数器和分频器)只能由后备域复位

● 3个专门的可屏蔽中断：
● 1.闹钟中断，用来产生一个软件可编程的闹钟中断。

● 2.秒中断，用来产生一个可编程的周期性中断信号(长可达1秒)。

● 3.溢出中断，指示内部可编程计数器溢出并回转为0的状态。

RTC时钟源：
三种不同的时钟源可被用来驱动系统时钟(SYSCLK)：

● HSI振荡器时钟
● HSE振荡器时钟
● PLL时钟

这些设备有以下2种二级时钟源：

● 40kHz低速内部RC，可以用于驱动独立看门狗和通过程序选择驱动RTC。 RTC用于从停机/待机模式下自动唤醒系统。
● 32.768kHz低速外部晶体也可用来通过程序选择驱动RTC(RTCCLK)。

RTC时钟的框图还是比较简单的，这里我们把他分成两个部分:

APB1 接口：用来和 APB1 总线相连。此单元还包含一组 16 位寄存器，可通过 APB1 总线对其进行读写操作。APB1 接口由 APB1 总线时钟驱动，用来与 APB1 总线连接。

通过APB1接口可以访问RTC的相关寄存器（预分频值，计数器值，闹钟值）。

RTC 核心接口：由一组可编程计数器组成，分成两个主要模块。
g)
第一个模块是 RTC 的预分频模块，它可编程产生 1 秒的 RTC 时间基准 TR_CLK。RTC 的预分频模块包含了一个 20 位的可编程分频器(RTC 预分频器)。如果在 RTC_CR 寄存器中设置了相应的允许位，则在每个 TR_CLK 周期中 RTC 产生一个中断(秒中断)。

第二个模块是一个 32 位的可编程计数器（RTC_CNT），可被初始化为当前的系统时间，一个 32 位的时钟计数器，按秒钟计算，可以记录 4294967296 秒，约合 136 年左右，作为一般应用，这已经是足够了的。

RTC具体流程：
RTCCLK经过RTC_DIV预分频，RTC_PRL设置预分频系数，然后得到TR_CLK时钟信号，我们一般设置其周期为1s，RTC_CNT计数器计数，假如1970设置为时间起点为0s，通过当前时间的秒数计算得到当前的时间。RTC_ALR是设置闹钟时间，RTC_CNT计数到RTC_ALR就会产生计数中断，

RTC_Second为秒中断，用于刷新时间，
RTC_Overflow是溢出中断。
RTC Alarm 控制开关机
RTC时钟选择
使用HSE分频时钟或者LSI的时候,在主电源VDD掉电的情况下,这两个时钟来源都会受到影响,因此没法保证RTC正常工作.所以RTC一般都时钟低速外部时钟LSE,频率为实时时钟模块中常用的32.768KHz,因为32768 = 2^15,分频容易实现,所以被广泛应用到RTC模块.(在主电源VDD有效的情况下(待机),RTC还可以配置闹钟事件使STM32退出待机模式).

RTC复位过程
除了RTC_PRL、RTC_ALR、RTC_CNT和RTC_DIV寄存器外，所有的系统寄存器都由系统复位或电源复位进行异步复位。
RTC_PRL、RTC_ALR、RTC_CNT和RTC_DIV寄存器仅能通过备份域复位信号复位。

系统复位后,禁止访问后备寄存器和RCT,防止对后卫区域(BKP)的意外写操作

RTC中断
秒中断：
这里时钟自带一个秒中断，每当计数加一的时候就会触发一次秒中断，。注意，这里所说的秒中断并非一定是一秒的时间，它是由RTC时钟源和分频值决定的“秒”的时间，当然也是可以做到1秒钟中断一次。我们通过往秒中断里写更新时间的函数来达到时间同步的效果

闹钟中断：
闹钟中断就是设置一个预设定的值，计数每自加多少次触发一次闹钟中断

二.创建CubeMX工程

创建STM32F103C8工程

配置RCC（设置高速外部时钟，使能外部晶振LSE）

配置RTC（激活时钟源(Activate Clock Source)和日历(Activate Calendar)）

RTC_OUT： Not RTC_OUT
Tamper： ×
第一个是是否使能 tamper（PC13）引脚上输出校正的秒脉冲时钟，

第二个： RTC入侵检测校验功能

RTC校验功能，使能侵入检测功能。RTC时钟经64分频输出到侵入检测引脚TAMPER上
当 TAMPER引脚上的信号从 0变成1或者从 1变成 0(取决于备份控制寄存器BKP_CR的 TPAL位)，会产生一个侵入检测事件。侵入检测事件将所有数据备份寄存器内容清除。

也就是第一个是使能tamper（PC13）引脚作为时钟脉冲输出
第二个是使能tamper（PC13）引脚作为入侵检测功能
下面是两个RTC的中断：

RTC全局中断RTC_IRQHandler()
闹钟中断函数RTCAlarm_IRQHandler()

设置时间为创建时间2023/11/22 20:25

使能串口

设置项目

在main.c文件中重写fputc函数，完成printf函数的重定向：

//添加头文件#include "stdio.h"
int fputc(int ch,FILE *f){
 uint8_t temp[1]={ch};
 HAL_UART_Transmit(&huart1,temp,1,2);
 return ch;
}

在main.c中定义时间和日期的结构体用来获取时间和日期：

RTC_DateTypeDef GetData;  //获取日期结构体
 
RTC_TimeTypeDef GetTime;   //获取时间结构体

在main函数中while循环里面添加如下代码

/* Get the RTC current Time */
	    HAL_RTC_GetTime(&hrtc, &GetTime, RTC_FORMAT_BIN);
      /* Get the RTC current Date */
      HAL_RTC_GetDate(&hrtc, &GetData, RTC_FORMAT_BIN);
 
      /* Display date Format : yy/mm/dd */
      printf("%02d/%02d/%02d\r\n",2000 + GetData.Year, GetData.Month, GetData.Date);
	  /* Display date Format : weekday */
		if(GetData.WeekDay==1){
			printf("星期一\r\n");
		}else if(GetData.WeekDay==2){
			printf("星期二\r\n");
		}else if(GetData.WeekDay==3){
			printf("星期三\r\n");
		}else if(GetData.WeekDay==4){
			printf("星期四\r\n");
		}else if(GetData.WeekDay==5){
			printf("星期五\r\n");
		}else if(GetData.WeekDay==6){
			printf("星期六\r\n");
		}else if(GetData.WeekDay==7){
			printf("星期日\r\n");
		}
 
      /* Display time Format : hh:mm:ss */
      printf("%02d:%02d:%02d\r\n",GetTime.Hours, GetTime.Minutes, GetTime.Seconds);
 
      printf("\r\n");
 
      HAL_Delay(1000);

注意：因为我们在代码里面重写了printf，所以在Target里面一定要勾选上Use MiscroLiB：

运行成功！！！

2) 读取AHT20的温度和湿度，通过OLED，把年月份时分秒、日历和实时温度、湿度显示出来，2秒周期。

RTC程序

RTC.c

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file    rtc.c
  * @brief   This file provides code for the configuration
  *          of the RTC instances.
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2023 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "rtc.h"
 
/* USER CODE BEGIN 0 */
 
/* USER CODE END 0 */
 
RTC_HandleTypeDef hrtc;
 
/* RTC init function */
void MX_RTC_Init(void)
{
 
  /* USER CODE BEGIN RTC_Init 0 */
 
  /* USER CODE END RTC_Init 0 */
 
  RTC_TimeTypeDef sTime = {0};
  RTC_DateTypeDef DateToUpdate = {0};
 
  /* USER CODE BEGIN RTC_Init 1 */
 
  /* USER CODE END RTC_Init 1 */
 
  /** Initialize RTC Only
  */
  hrtc.Instance = RTC;
  hrtc.Init.AsynchPrediv = RTC_AUTO_1_SECOND;
  hrtc.Init.OutPut = RTC_OUTPUTSOURCE_NONE;
  if (HAL_RTC_Init(&hrtc) != HAL_OK)
  {
    Error_Handler();
  }
 
  /* USER CODE BEGIN Check_RTC_BKUP */
 
  /* USER CODE END Check_RTC_BKUP */
 
  /** Initialize RTC and set the Time and Date
  */
  sTime.Hours = 0x10;
  sTime.Minutes = 0x59;
  sTime.Seconds = 0x10;
 
  if (HAL_RTC_SetTime(&hrtc, &sTime, RTC_FORMAT_BCD) != HAL_OK)
  {
    Error_Handler();
  }
  DateToUpdate.WeekDay = RTC_WEEKDAY_THURSDAY;
  DateToUpdate.Month = RTC_MONTH_NOVEMBER;
  DateToUpdate.Date = 0x23;
  DateToUpdate.Year = 0x23;
 
  if (HAL_RTC_SetDate(&hrtc, &DateToUpdate, RTC_FORMAT_BCD) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN RTC_Init 2 */
 
  /* USER CODE END RTC_Init 2 */
 
}
 
void HAL_RTC_MspInit(RTC_HandleTypeDef* rtcHandle)
{
 
  if(rtcHandle->Instance==RTC)
  {
  /* USER CODE BEGIN RTC_MspInit 0 */
 
  /* USER CODE END RTC_MspInit 0 */
    HAL_PWR_EnableBkUpAccess();
    /* Enable BKP CLK enable for backup registers */
    __HAL_RCC_BKP_CLK_ENABLE();
    /* RTC clock enable */
    __HAL_RCC_RTC_ENABLE();
 
    /* RTC interrupt Init */
    HAL_NVIC_SetPriority(RTC_IRQn, 0, 0);
    HAL_NVIC_EnableIRQ(RTC_IRQn);
  /* USER CODE BEGIN RTC_MspInit 1 */
 
  /* USER CODE END RTC_MspInit 1 */
  }
}
 
void HAL_RTC_MspDeInit(RTC_HandleTypeDef* rtcHandle)
{
 
  if(rtcHandle->Instance==RTC)
  {
  /* USER CODE BEGIN RTC_MspDeInit 0 */
 
  /* USER CODE END RTC_MspDeInit 0 */
    /* Peripheral clock disable */
    __HAL_RCC_RTC_DISABLE();
 
    /* RTC interrupt Deinit */
    HAL_NVIC_DisableIRQ(RTC_IRQn);
  /* USER CODE BEGIN RTC_MspDeInit 1 */
 
  /* USER CODE END RTC_MspDeInit 1 */
  }
}
 
/* USER CODE BEGIN 1 */
 
/* USER CODE END 1 */

oled

/***************************************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, QD electronic SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
****************************************************************************************************/	
#include "oled.h"
#include "stdlib.h"
#include "string.h" 	 
#include "stm32f1xx_hal.h"
#include "spi.h"
//OLEDÏÔ´æ×Ü¹²·ÖÎª8Ò³
//Ã¿Ò³8ÐÐ£¬Ò»ÐÐ128¸öÏñËØµã
//OLEDµÄÏÔ´æ
//´æ·Å¸ñÊ½ÈçÏÂ.
//[0]0 1 2 3 ... 127 (0~7)ÐÐ	   
//[1]0 1 2 3 ... 127 (8~15)ÐÐ	
//[2]0 1 2 3 ... 127 (16~23)ÐÐ	
//[3]0 1 2 3 ... 127 (24~31)ÐÐ	
//[4]0 1 2 3 ... 127 (32~39)ÐÐ	
//[5]0 1 2 3 ... 127 (40~47)ÐÐ	
//[6]0 1 2 3 ... 127 (48~55)ÐÐ	
//[7]0 1 2 3 ... 127 (56~63)ÐÐ			   
 
//Êý×éÃ¿¸öbit´æ´¢OLEDÃ¿¸öÏñËØµãµÄÑÕÉ«Öµ(1-ÁÁ(°×É«),0-Ãð(ºÚÉ«))
//Ã¿¸öÊý×éÔªËØ±íÊ¾1ÁÐ8¸öÏñËØµã£¬Ò»¹²128ÁÐ
static unsigned char OLED_buffer[1024] = 
{
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
};
 
/*******************************************************************
 * @name       :void OLED_WR_Byte(unsigned dat,unsigned cmd)
 * @date       :2018-08-27
 * @function   :Write a byte of content to the OLED screen
 * @parameters :dat:Content to be written
                cmd:0-write command
								    1-write data
 * @retvalue   :None
********************************************************************/
 
uint8_t SPI1_ReadWriteByte(uint8_t TxData)
{		
	uint8_t rxdata = 1;
	#if onlysend //Èç¹ûÖ»ÅäÖÃÁË·¢ËÍ Ê¹ÓÃHAL_SPI_Transmit
	HAL_SPI_Transmit(&hspi1,&TxData,1,100);
	//while(HAL_SPI_GetState(&hspi1) == HAL_SPI_STATE_READY);
	#else//Èç¹ûÅäÖÃÁË·¢ËÍºÍ½ÓÊÕ Ê¹ÓÃHAL_SPI_TransmitReceive
	if(HAL_OK == HAL_SPI_TransmitReceive(&hspi1,&TxData,&rxdata,1,100))
	{	
		return rxdata;	
	};
	#endif
	return rxdata;	    
}
 
 
void OLED_WR_Byte(unsigned dat,unsigned cmd)
{
	if(cmd)
	{
		OLED_DC_Set();
	}
	else
	{
		OLED_DC_Clr();
	}
	OLED_CS_Clr();
	SPI1_ReadWriteByte(dat);
	OLED_CS_Set();
}
 
/*******************************************************************
 * @name       :void OLED_Set_Pos(unsigned char x, unsigned char y) 
 * @date       :2018-08-27
 * @function   :Set coordinates in the OLED screen
 * @parameters :x:x coordinates
                y:y coordinates
 * @retvalue   :None
********************************************************************/
void OLED_Set_Pos(unsigned char x, unsigned char y) 
{
 	OLED_WR_Byte(YLevel+y/PAGE_SIZE,OLED_CMD);
	OLED_WR_Byte((((x+2)&0xf0)>>4)|0x10,OLED_CMD);
	OLED_WR_Byte(((x+2)&0x0f),OLED_CMD); 
}  
 
/*******************************************************************
 * @name       :void OLED_Display_On(void) 
 * @date       :2018-08-27
 * @function   :Turn on OLED display
 * @parameters :None
 * @retvalue   :None
********************************************************************/ 	  
void OLED_Display_On(void)
{
	OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDCÃüÁî
	OLED_WR_Byte(0X14,OLED_CMD);  //DCDC ON
	OLED_WR_Byte(0XAF,OLED_CMD);  //DISPLAY ON
}
 
/*******************************************************************
 * @name       :void OLED_Display_Off(void)
 * @date       :2018-08-27
 * @function   :Turn off OLED display
 * @parameters :None
 * @retvalue   :None
********************************************************************/    
void OLED_Display_Off(void)
{
	OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDCÃüÁî
	OLED_WR_Byte(0X10,OLED_CMD);  //DCDC OFF
	OLED_WR_Byte(0XAE,OLED_CMD);  //DISPLAY OFF
}
 
/*******************************************************************
 * @name       :void OLED_Set_Pixel(unsigned char x, unsigned char y,unsigned char color)
 * @date       :2018-08-27
 * @function   :set the value of pixel to RAM
 * @parameters :x:the x coordinates of pixel
                y:the y coordinates of pixel
								color:the color value of the point
								      1-white
											0-black
 * @retvalue   :None
********************************************************************/ 
void OLED_Set_Pixel(unsigned char x, unsigned char y,unsigned char color)
{
	if(color)
	{
		OLED_buffer[(y/PAGE_SIZE)*WIDTH+x]|= (1<<(y%PAGE_SIZE))&0xff;
	}
	else
	{
		OLED_buffer[(y/PAGE_SIZE)*WIDTH+x]&= ~((1<<(y%PAGE_SIZE))&0xff);
	}
}		   			 
 
/*******************************************************************
 * @name       :void OLED_Display(void)
 * @date       :2018-08-27
 * @function   :Display in OLED screen
 * @parameters :None
 * @retvalue   :None
********************************************************************/  
void OLED_Display(void)
{
	uint8_t i,n;		    
	for(i=0;i<PAGE_SIZE;i++)  
	{  
		OLED_WR_Byte (YLevel+i,OLED_CMD);    //ÉèÖÃÒ³µØÖ·£¨0~7£©
		OLED_WR_Byte (XLevelL,OLED_CMD);      //ÉèÖÃÏÔÊ¾Î»ÖÃ¡ªÁÐµÍµØÖ·
		OLED_WR_Byte (XLevelH,OLED_CMD);      //ÉèÖÃÏÔÊ¾Î»ÖÃ¡ªÁÐ¸ßµØÖ·   
		for(n=0;n<WIDTH;n++)
		{
			OLED_WR_Byte(OLED_buffer[i*WIDTH+n],OLED_DATA); 
		}
	}   //¸üÐÂÏÔÊ¾
}
 
/*******************************************************************
 * @name       :void OLED_Clear(unsigned dat)  
 * @date       :2018-08-27
 * @function   :clear OLED screen
 * @parameters :dat:0-Display full black
                    1-Display full white
 * @retvalue   :None
********************************************************************/ 
void OLED_Clear(unsigned dat)  
{  
	if(dat)
	{
		memset(OLED_buffer,0xff,sizeof(OLED_buffer));
	}
	else
	{
		memset(OLED_buffer,0,sizeof(OLED_buffer));
	}
	OLED_Display();
}
 
/*******************************************************************
 * @name       :void OLED_Reset(void) 
 * @date       :2018-08-27
 * @function   :Reset OLED screen
 * @parameters :dat:0-Display full black
                    1-Display full white
 * @retvalue   :None
********************************************************************/ 
void OLED_Reset(void)
{
	OLED_RST_Set();
	HAL_Delay(100);
	OLED_RST_Clr();
	HAL_Delay(100);
	OLED_RST_Set(); 
}	
	
/*******************************************************************
 * @name       :void OLED_Init_GPIO(void)
 * @date       :2018-08-27
 * @function   :Reset OLED screen
 * @parameters :None
 * @retvalue   :None
********************************************************************/ 
void OLED_Init_GPIO(void)
{
	GPIO_InitTypeDef  GPIO_InitStructure = {0};
  __HAL_RCC_GPIOA_CLK_ENABLE();
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_6, GPIO_PIN_RESET);//Ê¹ÄÜB¶Ë¿ÚÊ±ÖÓ
	GPIO_InitStructure.Pin = GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_6;	//GPIOB10,11,12 
 	GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP; 		 //ÍÆÍìÊä³ö
  GPIO_InitStructure.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_6, GPIO_PIN_SET);//Ê¹ÄÜB¶Ë¿ÚÊ±ÖÓ
}
 
/*******************************************************************
 * @name       :void OLED_Init(void)
 * @date       :2018-08-27
 * @function   :initialise OLED SH1106 control IC
 * @parameters :None
 * @retvalue   :None
********************************************************************/ 				    
void OLED_Init(void)
{
 	OLED_Init_GPIO(); //³õÊ¼»¯GPIO
 	HAL_Delay(200);
	OLED_Reset();     //¸´Î»OLED
 
/**************³õÊ¼»¯SSD1306*****************/	
	OLED_WR_Byte(0xAE,OLED_CMD); /*display off*/
	OLED_WR_Byte(0x00,OLED_CMD); /*set lower column address*/
	OLED_WR_Byte(0x10,OLED_CMD); /*set higher column address*/
	OLED_WR_Byte(0x40,OLED_CMD); /*set display start line*/ 
	OLED_WR_Byte(0xB0,OLED_CMD); /*set page address*/
	OLED_WR_Byte(0x81,OLED_CMD); /*contract control*/ 
	OLED_WR_Byte(0xFF,OLED_CMD); /*128*/
	OLED_WR_Byte(0xA1,OLED_CMD); /*set segment remap*/ 
	OLED_WR_Byte(0xA6,OLED_CMD); /*normal / reverse*/
	OLED_WR_Byte(0xA8,OLED_CMD); /*multiplex ratio*/ 
	OLED_WR_Byte(0x3F,OLED_CMD); /*duty = 1/64*/
	OLED_WR_Byte(0xC8,OLED_CMD); /*Com scan direction*/
	OLED_WR_Byte(0xD3,OLED_CMD); /*set display offset*/ 
	OLED_WR_Byte(0x00,OLED_CMD);
	OLED_WR_Byte(0xD5,OLED_CMD); /*set osc division*/ 
	OLED_WR_Byte(0x80,OLED_CMD);
	OLED_WR_Byte(0xD9,OLED_CMD); /*set pre-charge period*/ 
	OLED_WR_Byte(0XF1,OLED_CMD);
	OLED_WR_Byte(0xDA,OLED_CMD); /*set COM pins*/ 
	OLED_WR_Byte(0x12,OLED_CMD);
	OLED_WR_Byte(0xDB,OLED_CMD); /*set vcomh*/ 
	OLED_WR_Byte(0x30,OLED_CMD);
	OLED_WR_Byte(0x8D,OLED_CMD); /*set charge pump disable*/ 
	OLED_WR_Byte(0x14,OLED_CMD);
	OLED_WR_Byte(0xAF,OLED_CMD); /*display ON*/
}

oledfont,h

/***************************************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, QD electronic SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
****************************************************************************************************/	
#ifndef __OLEDFONT_H
#define __OLEDFONT_H 	   
//³£ÓÃASCII±í
//Æ«ÒÆÁ¿32
//ASCII×Ö·û¼¯
//Æ«ÒÆÁ¿32
//´óÐ¡:6*8
//ÖðÐÐÊ½£¬Ë³Ïò£¨¸ßÎ»ÔÚÇ°£©
/************************************6*8µÄµãÕó************************************/
const unsigned char F6x8[][8] =		
{
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // sp
	0x10,0x10,0x10,0x10,0x00,0x10,0x00,0x00, // !
	0x28,0x28,0x28,0x00,0x00,0x00,0x00,0x00, // "
	0x28,0x28,0x7C,0x28,0x7C,0x28,0x28,0x00, // #
	0x10,0x3C,0x50,0x38,0x14,0x78,0x10,0x00, // $
	0x00,0x4C,0x2C,0x10,0x08,0x60,0x60,0x00, // %
	0x30,0x48,0x50,0x20,0x54,0x48,0x34,0x00, // &
	0x30,0x10,0x20,0x00,0x00,0x00,0x00,0x00, // '
	0x08,0x10,0x20,0x20,0x20,0x10,0x08,0x00, // (
	0x20,0x10,0x08,0x08,0x08,0x10,0x20,0x00, // )
	0x00,0x10,0x54,0x38,0x54,0x10,0x00,0x00, // *
	0x00,0x10,0x10,0x7C,0x10,0x10,0x00,0x00, // +
	0x00,0x00,0x00,0x00,0x00,0x18,0x08,0x10, // ,
	0x00,0x00,0x00,0x00,0x7C,0x00,0x00,0x00, // -
	0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00, // .
	0x00,0x04,0x08,0x10,0x20,0x40,0x00,0x00, // /
	0x38,0x44,0x4C,0x54,0x64,0x44,0x38,0x00, // 0
	0x10,0x30,0x10,0x10,0x10,0x10,0x38,0x00, // 1
	0x38,0x44,0x04,0x08,0x10,0x20,0x7C,0x00, // 2
	0x7C,0x08,0x10,0x08,0x04,0x44,0x38,0x00, // 3 
	0x08,0x18,0x28,0x48,0x7C,0x08,0x08,0x00, // 4
	0x7C,0x40,0x78,0x04,0x04,0x44,0x38,0x00, // 5
	0x18,0x20,0x40,0x78,0x44,0x44,0x38,0x00, // 6
	0x7C,0x04,0x08,0x10,0x20,0x20,0x20,0x00, // 7
	0x38,0x44,0x44,0x38,0x44,0x44,0x38,0x00, // 8
	0x38,0x44,0x44,0x3C,0x04,0x08,0x30,0x00, // 9
	0x00,0x30,0x30,0x00,0x30,0x30,0x00,0x00, // :
	0x00,0x30,0x30,0x00,0x30,0x10,0x20,0x00, // ;
	0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x00, // <
	0x00,0x00,0x7C,0x00,0x7C,0x00,0x00,0x00, // =
	0x20,0x10,0x08,0x04,0x08,0x10,0x20,0x00, // >
	0x38,0x44,0x04,0x08,0x10,0x00,0x10,0x00, // ?
	0x38,0x44,0x04,0x34,0x5C,0x44,0x38,0x00, // @
	0x10,0x28,0x44,0x44,0x7C,0x44,0x44,0x00, // A
	0x78,0x44,0x44,0x78,0x44,0x44,0x78,0x00, // B
	0x38,0x44,0x40,0x40,0x40,0x44,0x38,0x00, // C
	0x70,0x48,0x44,0x44,0x44,0x48,0x70,0x00, // D
	0x7C,0x40,0x40,0x78,0x40,0x40,0x7C,0x00, // E
	0x7C,0x40,0x40,0x78,0x40,0x40,0x40,0x00, // F
	0x38,0x44,0x40,0x5C,0x44,0x44,0x3C,0x00, // G
	0x44,0x44,0x44,0x7C,0x44,0x44,0x44,0x00, // H
	0x38,0x10,0x10,0x10,0x10,0x10,0x38,0x00, // I
	0x1C,0x08,0x08,0x08,0x08,0x48,0x30,0x00, // J
	0x44,0x48,0x50,0x60,0x50,0x48,0x44,0x00, // K
	0x40,0x40,0x40,0x40,0x40,0x40,0x7C,0x00, // L
	0x44,0x6C,0x54,0x54,0x44,0x44,0x44,0x00, // M
	0x44,0x44,0x64,0x54,0x4C,0x44,0x44,0x00, // N
	0x38,0x44,0x44,0x44,0x44,0x44,0x38,0x00, // O
	0x78,0x44,0x44,0x78,0x40,0x40,0x40,0x00, // P
	0x38,0x44,0x44,0x44,0x54,0x48,0x34,0x00, // Q
	0x78,0x44,0x44,0x78,0x50,0x48,0x44,0x00, // R
	0x3C,0x40,0x40,0x38,0x04,0x04,0x78,0x00, // S
	0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x00, // T
	0x44,0x44,0x44,0x44,0x44,0x44,0x38,0x00, // U
	0x44,0x44,0x44,0x44,0x44,0x28,0x10,0x00, // V
	0x44,0x44,0x44,0x54,0x54,0x54,0x28,0x00, // W
	0x44,0x44,0x28,0x10,0x28,0x44,0x44,0x00, // X
	0x44,0x44,0x44,0x28,0x10,0x10,0x10,0x00, // Y
	0x7C,0x04,0x08,0x10,0x20,0x40,0x7C,0x00, // Z
	0x38,0x20,0x20,0x20,0x20,0x20,0x38,0x00, // [
	0x00,0x40,0x20,0x10,0x08,0x04,0x00,0x00, // '\'
	0x38,0x08,0x08,0x08,0x08,0x08,0x38,0x00, // ]
	0x10,0x28,0x44,0x00,0x00,0x00,0x00,0x00, // ^
	0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x00, // _
	0x20,0x10,0x08,0x00,0x00,0x00,0x00,0x00, // '
	0x00,0x00,0x38,0x04,0x3C,0x44,0x3C,0x00, // a
	0x40,0x40,0x58,0x64,0x44,0x44,0x78,0x00, // b
	0x00,0x00,0x38,0x40,0x40,0x44,0x38,0x00, // c
	0x04,0x04,0x34,0x4C,0x44,0x44,0x3C,0x00, // d
	0x00,0x00,0x38,0x44,0x7C,0x40,0x38,0x00, // e
	0x38,0x24,0x20,0x70,0x20,0x20,0x20,0x00, // f
	0x00,0x00,0x3C,0x44,0x44,0x3C,0x04,0x38, // g
	0x40,0x40,0x58,0x64,0x44,0x44,0x44,0x00, // h
	0x10,0x00,0x30,0x10,0x10,0x10,0x38,0x00, // i
	0x08,0x00,0x18,0x08,0x08,0x08,0x48,0x30, // j
	0x40,0x40,0x48,0x50,0x60,0x50,0x48,0x00, // k
	0x30,0x10,0x10,0x10,0x10,0x10,0x38,0x00, // l
	0x00,0x00,0x68,0x54,0x54,0x44,0x44,0x00, // m
	0x00,0x00,0x58,0x64,0x44,0x44,0x44,0x00, // n
	0x00,0x00,0x38,0x44,0x44,0x44,0x38,0x00, // o
	0x00,0x00,0x58,0x64,0x64,0x58,0x40,0x40, // p
	0x00,0x00,0x34,0x4C,0x4C,0x34,0x04,0x04, // q
	0x00,0x00,0x58,0x64,0x40,0x40,0x40,0x00, // r
	0x00,0x00,0x3C,0x40,0x38,0x04,0x78,0x00, // s
	0x20,0x20,0x70,0x20,0x20,0x24,0x18,0x00, // t
	0x00,0x00,0x44,0x44,0x44,0x4C,0x34,0x00, // u
	0x00,0x00,0x44,0x44,0x44,0x28,0x10,0x00, // v
	0x00,0x00,0x44,0x44,0x54,0x54,0x28,0x00, // w
	0x00,0x00,0x44,0x28,0x10,0x28,0x44,0x00, // x
	0x00,0x00,0x44,0x44,0x44,0x3C,0x04,0x38, // y
	0x00,0x00,0x7C,0x08,0x10,0x20,0x7C,0x00, // z
	0x10,0x20,0x20,0x40,0x20,0x20,0x10,0x00, // {
	0x00,0x10,0x10,0x10,0x10,0x10,0x10,0x00, // |
	0x20,0x10,0x10,0x08,0x10,0x10,0x20,0x00, // }
	0x00,0x00,0x00,0x20,0x54,0x08,0x00,0x00, // ~
};
 
//³£ÓÃASCII±í
//Æ«ÒÆÁ¿32
//ASCII×Ö·û¼¯
//Æ«ÒÆÁ¿32
//´óÐ¡:8*16
//ÖðÐÐÊ½£¬Ë³Ïò£¨¸ßÎ»ÔÚÇ°£©
/****************************************8*16µÄµãÕó************************************/
const unsigned char F8X16[]=	  
{
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
  0x00,0x00,0x00,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x00,0x00,0x18,0x18,0x00,0x00,//! 1
  0x00,0x12,0x36,0x24,0x48,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2
  0x00,0x00,0x00,0x24,0x24,0x24,0xFE,0x48,0x48,0x48,0xFE,0x48,0x48,0x48,0x00,0x00,//# 3
  0x00,0x00,0x10,0x38,0x54,0x54,0x50,0x30,0x1C,0x14,0x14,0x54,0x54,0x38,0x10,0x10,//$ 4
  0x00,0x00,0x00,0x44,0xA4,0xA8,0xA8,0xA8,0x54,0x1A,0x2A,0x2A,0x2A,0x44,0x00,0x00,//% 5
  0x00,0x00,0x00,0x30,0x48,0x48,0x48,0x50,0x6E,0xA4,0x94,0x88,0x89,0x76,0x00,0x00,//& 6
  0x00,0x60,0x60,0x20,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7
  0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00,//( 8
  0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00,//) 9
  0x00,0x00,0x00,0x00,0x10,0x10,0xD6,0x38,0x38,0xD6,0x10,0x10,0x00,0x00,0x00,0x00,//* 10
  0x00,0x00,0x00,0x00,0x10,0x10,0x10,0x10,0xFE,0x10,0x10,0x10,0x10,0x00,0x00,0x00,//+ 11
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x60,0x20,0xC0,//, 12
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//- 13
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x60,0x00,0x00,//. 14
  0x00,0x00,0x01,0x02,0x02,0x04,0x04,0x08,0x08,0x10,0x10,0x20,0x20,0x40,0x40,0x00,/// 15
  0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00,//0 16
  0x00,0x00,0x00,0x10,0x70,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00,//1 17
  0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x04,0x04,0x08,0x10,0x20,0x42,0x7E,0x00,0x00,//2 18
  0x00,0x00,0x00,0x3C,0x42,0x42,0x04,0x18,0x04,0x02,0x02,0x42,0x44,0x38,0x00,0x00,//3 19
  0x00,0x00,0x00,0x04,0x0C,0x14,0x24,0x24,0x44,0x44,0x7E,0x04,0x04,0x1E,0x00,0x00,//4 20
  0x00,0x00,0x00,0x7E,0x40,0x40,0x40,0x58,0x64,0x02,0x02,0x42,0x44,0x38,0x00,0x00,//5 21
  0x00,0x00,0x00,0x1C,0x24,0x40,0x40,0x58,0x64,0x42,0x42,0x42,0x24,0x18,0x00,0x00,//6 22
  0x00,0x00,0x00,0x7E,0x42,0x44,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x00,0x00,//7 23
  0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00,//8 24
  0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x26,0x1A,0x02,0x02,0x24,0x38,0x00,0x00,//9 25
  0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,//: 26
  0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x18,0x18,0x08,0x30,0x00,//; 27
  0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00,//< 28
  0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,//= 29
  0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00,//> 30
  0x00,0x00,0x00,0x3C,0x42,0x42,0x62,0x02,0x04,0x08,0x08,0x00,0x18,0x18,0x00,0x00,//? 31
  0x00,0x00,0x00,0x38,0x44,0x5A,0xAA,0xAA,0xAA,0xAA,0xB4,0x42,0x44,0x38,0x00,0x00,//@ 32
  0x00,0x00,0x00,0x10,0x10,0x18,0x28,0x28,0x24,0x3C,0x44,0x42,0x42,0xE7,0x00,0x00,//A 33
  0x00,0x00,0x00,0xF8,0x44,0x44,0x44,0x78,0x44,0x42,0x42,0x42,0x44,0xF8,0x00,0x00,//B 34
  0x00,0x00,0x00,0x3E,0x42,0x42,0x80,0x80,0x80,0x80,0x80,0x42,0x44,0x38,0x00,0x00,//C 35
  0x00,0x00,0x00,0xF8,0x44,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x44,0xF8,0x00,0x00,//D 36
  0x00,0x00,0x00,0xFE,0x42,0x48,0x48,0x78,0x48,0x48,0x40,0x42,0x42,0xFE,0x00,0x00,//E 37
  0x00,0x00,0x00,0xFE,0x42,0x48,0x48,0x78,0x48,0x48,0x40,0x40,0x40,0xE0,0x00,0x00,//F 38
  0x00,0x00,0x00,0x3C,0x44,0x44,0x80,0x80,0x80,0x8E,0x84,0x44,0x44,0x38,0x00,0x00,//G 39
  0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,//H 40
  0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00,//I 41
  0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x88,0xF0,//J 42
  0x00,0x00,0x00,0xEE,0x44,0x48,0x50,0x70,0x50,0x48,0x48,0x44,0x44,0xEE,0x00,0x00,//K 43
  0x00,0x00,0x00,0xE0,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x42,0xFE,0x00,0x00,//L 44
  0x00,0x00,0x00,0xEE,0x6C,0x6C,0x6C,0x6C,0x54,0x54,0x54,0x54,0x54,0xD6,0x00,0x00,//M 45
  0x00,0x00,0x00,0xC7,0x62,0x62,0x52,0x52,0x4A,0x4A,0x4A,0x46,0x46,0xE2,0x00,0x00,//N 46
  0x00,0x00,0x00,0x38,0x44,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0x44,0x38,0x00,0x00,//O 47
  0x00,0x00,0x00,0xFC,0x42,0x42,0x42,0x42,0x7C,0x40,0x40,0x40,0x40,0xE0,0x00,0x00,//P 48
  0x00,0x00,0x00,0x38,0x44,0x82,0x82,0x82,0x82,0x82,0xB2,0xCA,0x4C,0x38,0x06,0x00,//Q 49
  0x00,0x00,0x00,0xF8,0x44,0x44,0x44,0x78,0x48,0x48,0x44,0x44,0x42,0xE3,0x00,0x00,//R 50
  0x00,0x00,0x00,0x3E,0x42,0x42,0x40,0x20,0x18,0x04,0x02,0x42,0x42,0x7C,0x00,0x00,//S 51
  0x00,0x00,0x00,0xFE,0x92,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x38,0x00,0x00,//T 52
  0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00,//U 53
  0x00,0x00,0x00,0xE7,0x42,0x42,0x44,0x24,0x24,0x28,0x28,0x18,0x10,0x10,0x00,0x00,//V 54
  0x00,0x00,0x00,0xD6,0x92,0x92,0x92,0x92,0xAA,0xAA,0x6C,0x44,0x44,0x44,0x00,0x00,//W 55
  0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00,//X 56
  0x00,0x00,0x00,0xEE,0x44,0x44,0x28,0x28,0x10,0x10,0x10,0x10,0x10,0x38,0x00,0x00,//Y 57
  0x00,0x00,0x00,0x7E,0x84,0x04,0x08,0x08,0x10,0x20,0x20,0x42,0x42,0xFC,0x00,0x00,//Z 58
  0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00,//[ 59
  0x00,0x00,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x04,0x04,0x02,0x02,0x02,0x01,0x01,//\ 60
  0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00,//] 61
  0x00,0x08,0x14,0x22,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,//_ 63
  0x00,0x60,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x1E,0x22,0x42,0x42,0x3F,0x00,0x00,//a 65
  0x00,0x00,0x00,0xC0,0x40,0x40,0x40,0x58,0x64,0x42,0x42,0x42,0x64,0x58,0x00,0x00,//b 66
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x22,0x40,0x40,0x40,0x22,0x1C,0x00,0x00,//c 67
  0x00,0x00,0x00,0x06,0x02,0x02,0x02,0x1E,0x22,0x42,0x42,0x42,0x26,0x1B,0x00,0x00,//d 68
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x40,0x40,0x42,0x3C,0x00,0x00,//e 69
  0x00,0x00,0x00,0x0F,0x11,0x10,0x10,0x7E,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00,//f 70
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3E,0x44,0x44,0x38,0x40,0x3C,0x42,0x42,0x3C,//g 71
  0x00,0x00,0x00,0xC0,0x40,0x40,0x40,0x5C,0x62,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,//h 72
  0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x70,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00,//i 73
  0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x1C,0x04,0x04,0x04,0x04,0x04,0x04,0x44,0x78,//j 74
  0x00,0x00,0x00,0xC0,0x40,0x40,0x40,0x4E,0x48,0x50,0x68,0x48,0x44,0xEE,0x00,0x00,//k 75
  0x00,0x00,0x00,0x70,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x7C,0x00,0x00,//l 76
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF6,0x49,0x49,0x49,0x49,0x49,0xED,0x00,0x00,//m 77
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xDC,0x62,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,//n 78
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00,//o 79
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xD8,0x64,0x42,0x42,0x42,0x64,0x58,0x40,0xE0,//p 80
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1E,0x22,0x42,0x42,0x42,0x26,0x1A,0x02,0x07,//q 81
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEE,0x32,0x20,0x20,0x20,0x20,0xF8,0x00,0x00,//r 82
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3E,0x42,0x40,0x3C,0x02,0x42,0x7C,0x00,0x00,//s 83
  0x00,0x00,0x00,0x00,0x00,0x10,0x10,0x7C,0x10,0x10,0x10,0x10,0x10,0x0C,0x00,0x00,//t 84
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC6,0x42,0x42,0x42,0x42,0x46,0x3B,0x00,0x00,//u 85
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x28,0x10,0x10,0x00,0x00,//v 86
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xD7,0x92,0x92,0xAA,0xAA,0x44,0x44,0x00,0x00,//w 87
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x6E,0x24,0x18,0x18,0x18,0x24,0x76,0x00,0x00,//x 88
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x28,0x18,0x10,0x10,0xE0,//y 89
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x44,0x08,0x10,0x10,0x22,0x7E,0x00,0x00,//z 90
  0x00,0x03,0x04,0x04,0x04,0x04,0x04,0x08,0x04,0x04,0x04,0x04,0x04,0x04,0x03,0x00,//{ 91
  0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,//| 92
  0x00,0x60,0x10,0x10,0x10,0x10,0x10,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x60,0x00,//} 93
  0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x52,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};
 
typedef struct 
{
	unsigned char Index[2];	
	char Msk[32];
}typFNT_GB16; 
 
//ËÎÌå
//16*16´óÐ¡
//ÖðÐÐÊ½£¬Ë³Ïò£¨¸ßÎ»ÔÚÇ°£©
const typFNT_GB16 cfont16[] = 
{
  "µ±",0x01,0x00,0x21,0x08,0x11,0x08,0x09,0x10,0x09,0x20,0x01,0x00,0x7F,0xF8,0x00,0x08,
  0x00,0x08,0x00,0x08,0x3F,0xF8,0x00,0x08,0x00,0x08,0x00,0x08,0x7F,0xF8,0x00,0x08,/*"?",0*/
  "Ç°",0x10,0x10,0x08,0x10,0x08,0x20,0xFF,0xFE,0x00,0x00,0x3E,0x08,0x22,0x48,0x22,0x48,
  0x3E,0x48,0x22,0x48,0x22,0x48,0x3E,0x48,0x22,0x08,0x22,0x08,0x2A,0x28,0x24,0x10,/*"?",1*/
  "Ê±",0x00,0x08,0x00,0x08,0x7C,0x08,0x44,0x08,0x45,0xFE,0x44,0x08,0x44,0x08,0x7C,0x08,
  0x44,0x88,0x44,0x48,0x44,0x48,0x44,0x08,0x7C,0x08,0x44,0x08,0x00,0x28,0x00,0x10,/*"?",2*/
  "¼ä",0x20,0x00,0x13,0xFC,0x10,0x04,0x40,0x04,0x47,0xC4,0x44,0x44,0x44,0x44,0x44,0x44,
  0x47,0xC4,0x44,0x44,0x44,0x44,0x44,0x44,0x47,0xC4,0x40,0x04,0x40,0x14,0x40,0x08,/*"?",3*/
  "£º",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
  0x00,0x00,0x30,0x00,0x30,0x00,0x00,0x00,0x30,0x00,0x30,0x00,0x00,0x00,0x00,0x00,/*":",0*/
  "ÎÂ",0x00,0x00,0x23,0xF8,0x12,0x08,0x12,0x08,0x83,0xF8,0x42,0x08,0x42,0x08,0x13,0xF8,
  0x10,0x00,0x27,0xFC,0xE4,0xA4,0x24,0xA4,0x24,0xA4,0x24,0xA4,0x2F,0xFE,0x00,0x00,/*"?",0*/
  "¶È",0x01,0x00,0x00,0x80,0x3F,0xFE,0x22,0x20,0x22,0x20,0x3F,0xFC,0x22,0x20,0x22,0x20,
  0x23,0xE0,0x20,0x00,0x2F,0xF0,0x24,0x10,0x42,0x20,0x41,0xC0,0x86,0x30,0x38,0x0E,/*"?",1*/
  "Êª",0x00,0x00,0x27,0xF8,0x14,0x08,0x14,0x08,0x87,0xF8,0x44,0x08,0x44,0x08,0x17,
  0xF8,0x11,0x20,0x21,0x20,0xE9,0x24,0x25,0x28,0x23,0x30,0x21,0x20,0x2F,0xFE,0x00,0x00,/*"?",2*/
   
  "ÈÕ",0x00,0x00,0x1F,0xF0,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1F,0xF0,
   0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1F,0xF0,0x10,0x10,/*"?",0*/
  "ÆÚ",0x22,0x00,0x22,0x7C,0x7F,0x44,0x22,0x44,0x22,0x44,0x3E,0x7C,0x22,0x44,0x22,0x44,
   0x3E,0x44,0x22,0x7C,0x22,0x44,0xFF,0x44,0x04,0x84,0x22,0x84,0x41,0x14,0x82,0x08,/*"?",1*/
	"¡æ",0x60,0x00,0x91,0xF4,0x96,0x0C,0x6C,0x04,0x08,0x04,0x18,0x00,0x18,0x00,0x18,0x00,
	0x18,0x00,0x18,0x00,0x18,0x00,0x08,0x00,0x0C,0x04,0x06,0x08,0x01,0xF0,0x00,0x00,/*"¡æ",0*/
};
 
#endif

gui.h

/***************************************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, QD electronic SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
****************************************************************************************************/		
#include "main.h"
#ifndef __GUI_H__
#define __GUI_H__
 
void GUI_DrawPoint(uint8_t x, uint8_t y, uint8_t color);
void GUI_Fill(uint8_t sx,uint8_t sy,uint8_t ex,uint8_t ey,uint8_t color);
void GUI_DrawLine(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color);
void GUI_DrawRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color);
void GUI_FillRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color);
void GUI_DrawCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r);
void GUI_FillCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r);
void GUI_DrawTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color);
void GUI_FillTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color);
void GUI_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t mode);
void GUI_ShowNum(uint8_t x,uint8_t y,uint32_t num,uint8_t len,uint8_t Size,uint8_t mode);
void GUI_ShowString(uint8_t x,uint8_t y,uint8_t *chr,uint8_t Char_Size,uint8_t mode);
void GUI_ShowFont16(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode);
void GUI_ShowFont24(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode);
void GUI_ShowFont32(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode);
void GUI_ShowCHinese(uint8_t x,uint8_t y,uint8_t hsize,uint8_t *str,uint8_t mode);
void GUI_DrawBMP(uint8_t x,uint8_t y,uint8_t width, uint8_t height, uint8_t BMP[], uint8_t mode); 
#endif

gui.c

/***************************************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, QD electronic SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
****************************************************************************************************/	
#include "oled.h"
#include "string.h"
#include "oledfont.h" 
#include "stm32f1xx_hal.h"
#include "gui.h"
 
/*******************************************************************
 * @name       :void GUI_DrawPoint(uint8_t x,uint8_t y,uint8_t color)
 * @date       :2018-08-27
 * @function   :draw a point in LCD screen
 * @parameters :x:the x coordinate of the point
                y:the y coordinate of the point
								color:the color value of the point
								      1-white
											0-black
 * @retvalue   :None
********************************************************************/
void GUI_DrawPoint(uint8_t x,uint8_t y,uint8_t color)
{
	OLED_Set_Pixel(x,y,color);
	OLED_Display();
}
 
/*******************************************************************
 * @name       :void GUI_Fill(uint8_t sx,uint8_t sy,uint8_t ex,uint8_t ey,uint8_t color)
 * @date       :2018-08-27 
 * @function   :fill the specified area
 * @parameters :sx:the bebinning x coordinate of the specified area
                sy:the bebinning y coordinate of the specified area
								ex:the ending x coordinate of the specified area
								ey:the ending y coordinate of the specified area
								color:the color value of the the specified area
								      1-white
											0-black
 * @retvalue   :None
********************************************************************/
void GUI_Fill(uint8_t sx,uint8_t sy,uint8_t ex,uint8_t ey,uint8_t color)
{  	
	uint8_t i,j;			
	uint8_t width=ex-sx+1; 		//得到填充的宽度
	uint8_t height=ey-sy+1;		//高度
	for(i=0;i<height;i++)
	{
		for(j=0;j<width;j++)
		{
				OLED_Set_Pixel(sx+j, sy+i,color);
		}		
	}
	OLED_Display();
}
 
/*******************************************************************
 * @name       :void GUI_DrawLine(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
 * @date       :2018-08-27 
 * @function   :Draw a line between two points
 * @parameters :x1:the bebinning x coordinate of the line
                y1:the bebinning y coordinate of the line
								x2:the ending x coordinate of the line
								y2:the ending y coordinate of the line
								color:the color value of the line
								      1-white
											0-black
 * @retvalue   :None
********************************************************************/
void GUI_DrawLine(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
{
	uint16_t t; 
	int xerr=0,yerr=0,delta_x,delta_y,distance; 
	int incx,incy,uRow,uCol; 
 
	delta_x=x2-x1; //计算坐标增量 
	delta_y=y2-y1; 
	uRow=x1; 
	uCol=y1; 
	if(delta_x>0)incx=1; //设置单步方向 
	else if(delta_x==0)incx=0;//垂直线 
	else {incx=-1;delta_x=-delta_x;} 
	if(delta_y>0)incy=1; 
	else if(delta_y==0)incy=0;//水平线 
	else{incy=-1;delta_y=-delta_y;} 
	if( delta_x>delta_y)distance=delta_x; //选取基本增量坐标轴 
	else distance=delta_y; 
	for(t=0;t<=distance+1;t++ )//画线输出 
	{ 
		OLED_Set_Pixel(uRow,uCol,color);
		xerr+=delta_x ; 
		yerr+=delta_y ; 
		if(xerr>distance) 
		{ 
			xerr-=distance; 
			uRow+=incx; 
		} 
		if(yerr>distance) 
		{ 
			yerr-=distance; 
			uCol+=incy; 
		} 
	}  
	OLED_Display();
} 
 
/*****************************************************************************
 * @name       :void GUI_DrawRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
 * @date       :2018-08-27 
 * @function   :Draw a rectangle
 * @parameters :x1:the bebinning x coordinate of the rectangle
                y1:the bebinning y coordinate of the rectangle
								x2:the ending x coordinate of the rectangle
								y2:the ending y coordinate of the rectangle
								color:the color value of the rectangle
								      1-white
											0-black							  
 * @retvalue   :None
******************************************************************************/
void GUI_DrawRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
{
	GUI_DrawLine(x1,y1,x2,y1,color);
	GUI_DrawLine(x1,y1,x1,y2,color);
	GUI_DrawLine(x1,y2,x2,y2,color);
	GUI_DrawLine(x2,y1,x2,y2,color);
}  
 
/*****************************************************************************
 * @name       :void GUI_FillRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
 * @date       :2018-08-27
 * @function   :Filled a rectangle
 * @parameters :x1:the bebinning x coordinate of the filled rectangle
                y1:the bebinning y coordinate of the filled rectangle
								x2:the ending x coordinate of the filled rectangle
								y2:the ending y coordinate of the filled rectangle
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/  
void GUI_FillRectangle(uint8_t x1, uint8_t y1, uint8_t x2, uint8_t y2,uint8_t color)
{
	GUI_Fill(x1,y1,x2,y2,color);
}
 
/*****************************************************************************
 * @name       :static void _draw_circle_8(uint8_t xc, uint8_t yc, uint8_t x, uint8_t y, uint8_t color)
 * @date       :2018-08-27 
 * @function   :8 symmetry circle drawing algorithm (internal call)
 * @parameters :xc:the x coordinate of the Circular center 
                yc:the y coordinate of the Circular center 
								x:the x coordinate relative to the Circular center 
								y:the y coordinate relative to the Circular center 
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/  
static void _draw_circle_8(uint8_t xc, uint8_t yc, uint8_t x, uint8_t y, uint8_t color)
{
	OLED_Set_Pixel(xc + x, yc + y, color);
	OLED_Set_Pixel(xc - x, yc + y, color);
	OLED_Set_Pixel(xc + x, yc - y, color);
	OLED_Set_Pixel(xc - x, yc - y, color);
	OLED_Set_Pixel(xc + y, yc + x, color);
	OLED_Set_Pixel(xc - y, yc + x, color);
	OLED_Set_Pixel(xc + y, yc - x, color);
	OLED_Set_Pixel(xc - y, yc - x, color);
}
 
/*****************************************************************************
 * @name       :void GUI_DrawCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r)
 * @date       :2018-08-27
 * @function   :Draw a circle of specified size at a specified location
 * @parameters :xc:the x coordinate of the Circular center 
                yc:the y coordinate of the Circular center 
								r:Circular radius
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/  
void GUI_DrawCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r)
{
	int x = 0, y = r,d;
	d = 3 - 2 * r;
	while (x <= y) 
	{
		_draw_circle_8(xc, yc, x, y, color);
		if (d < 0) 
		{
				d = d + 4 * x + 6;
		}
		else 
		{
				d = d + 4 * (x - y) + 10;
				y--;
		}
		x++;
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_FillCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r)
 * @date       :2018-08-27
 * @function   :Fill a circle of specified size at a specified location
 * @parameters :xc:the x coordinate of the Circular center 
                yc:the y coordinate of the Circular center 
								r:Circular radius
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/  
void GUI_FillCircle(uint8_t xc, uint8_t yc, uint8_t color, uint8_t r)
{
	int x = 0, y = r, yi, d;
	d = 3 - 2 * r;
	while (x <= y) 
	{
			for (yi = x; yi <= y; yi++)
			{
				_draw_circle_8(xc, yc, x, yi, color);
			}
			if (d < 0) 
			{
				d = d + 4 * x + 6;
			} 
			else 
			{
				d = d + 4 * (x - y) + 10;
				y--;
			}
			x++;
	}
	OLED_Display();
}
 
/**********************************************************************************
 * @name       :void GUI_DrawTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color)
 * @date       :2018-08-27 
 * @function   :Draw a triangle at a specified position
 * @parameters :x0:the bebinning x coordinate of the triangular edge 
                y0:the bebinning y coordinate of the triangular edge 
								x1:the vertex x coordinate of the triangular
								y1:the vertex y coordinate of the triangular
								x2:the ending x coordinate of the triangular edge 
								y2:the ending y coordinate of the triangular edge 
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
***********************************************************************************/ 
void GUI_DrawTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color)
{
	GUI_DrawLine(x0,y0,x1,y1,color);
	GUI_DrawLine(x1,y1,x2,y2,color);
	GUI_DrawLine(x2,y2,x0,y0,color);
}
 
/*****************************************************************************
 * @name       :static void _swap(uint8_t *a, uint8_t *b)
 * @date       :2018-08-27
 * @function   :Exchange two numbers(internal call)
 * @parameters :a:the address of the first number 
                b:the address of the second number
 * @retvalue   :None
******************************************************************************/  
static void _swap(uint8_t *a, uint8_t *b)
{
	uint16_t tmp;
  tmp = *a;
	*a = *b;
	*b = tmp;
}
 
/*****************************************************************************
 * @name       :static void _draw_h_line(uint8_t x0,uint8_t x1,uint8_t y,uint8_t color)
 * @date       :2018-08-27
 * @function   :draw a horizontal line in RAM(internal call)
 * @parameters :x0:the bebinning x coordinate of the horizontal line
                x1:the ending x coordinate of the horizontal line
								y:the y coordinate of the horizontal line
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/
static void _draw_h_line(uint8_t x0,uint8_t x1,uint8_t y,uint8_t color)
{
	uint8_t i=0;
	for(i=x0;i<=x1;i++)
	{
		OLED_Set_Pixel(i, y, color);
	}
}
 
/*****************************************************************************
 * @name       :void GUI_FillTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color)
 * @date       :2018-08-27 
 * @function   :filling a triangle at a specified position
 * @parameters :x0:the bebinning x coordinate of the triangular edge 
                y0:the bebinning y coordinate of the triangular edge 
								x1:the vertex x coordinate of the triangular
								y1:the vertex y coordinate of the triangular
								x2:the ending x coordinate of the triangular edge 
								y2:the ending y coordinate of the triangular edge 
								color:the color value of the rectangle
								      1-white
											0-black	
 * @retvalue   :None
******************************************************************************/ 
void GUI_FillTriangel(uint8_t x0,uint8_t y0,uint8_t x1,uint8_t y1,uint8_t x2,uint8_t y2,uint8_t color)
{
	uint8_t a, b, y, last;
	int dx01, dy01, dx02, dy02, dx12, dy12;
	long sa = 0;
	long sb = 0;
 	if (y0 > y1) 
	{
    _swap(&y0,&y1); 
		_swap(&x0,&x1);
 	}
 	if (y1 > y2) 
	{
    _swap(&y2,&y1); 
		_swap(&x2,&x1);
 	}
  if (y0 > y1) 
	{
    _swap(&y0,&y1); 
		_swap(&x0,&x1);
  }
	if(y0 == y2) 
	{ 
		a = b = x0;
		if(x1 < a)
    {
			a = x1;
    }
    else if(x1 > b)
    {
			b = x1;
    }
    if(x2 < a)
    {
			a = x2;
    }
		else if(x2 > b)
    {
			b = x2;
    }
		_draw_h_line(a,b,y0,color);
    return;
	}
	dx01 = x1 - x0;
	dy01 = y1 - y0;
	dx02 = x2 - x0;
	dy02 = y2 - y0;
	dx12 = x2 - x1;
	dy12 = y2 - y1;
	
	if(y1 == y2)
	{
		last = y1; 
	}
  else
	{
		last = y1-1; 
	}
	for(y=y0; y<=last; y++) 
	{
		a = x0 + sa / dy01;
		b = x0 + sb / dy02;
		sa += dx01;
    sb += dx02;
    if(a > b)
    {
			_swap(&a,&b);
		}
		_draw_h_line(a,b,y,color);
	}
	sa = dx12 * (y - y1);
	sb = dx02 * (y - y0);
	for(; y<=y2; y++) 
	{
		a = x1 + sa / dy12;
		b = x0 + sb / dy02;
		sa += dx12;
		sb += dx02;
		if(a > b)
		{
			_swap(&a,&b);
		}
		_draw_h_line(a,b,y,color);
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display a single English character
 * @parameters :x:the bebinning x coordinate of the Character display position
                y:the bebinning y coordinate of the Character display position
								chr:the ascii code of display character(0~94)
								Char_Size:the size of display character(8,16)
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/ 
void GUI_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t mode)
{      	
	  unsigned char c=0,i=0,tmp,j=0;	
		c=chr-' ';//得到偏移后的值			
		if(x>WIDTH-1){x=0;y=y+2;}
		if(Char_Size ==16)
		{
			for(i=0;i<16;i++)
			{
			  if(mode)
				{
					tmp = F8X16[c*16+i];
				}
				else
				{
					tmp = ~(F8X16[c*16+i]);
				}
				for(j=0;j<8;j++)
				{
					if(tmp&(0x80>>j))
					{
						OLED_Set_Pixel(x+j, y+i,1);
					}
					else
					{
						OLED_Set_Pixel(x+j, y+i,0);
					}
				}
			}
		}
		else if(Char_Size==8)
		{	
				for(i=0;i<8;i++)
				{
				  if(mode)
					{
						tmp = F6x8[c][i];
					}
					else
					{
						tmp = ~(F6x8[c][i]);
					}
					for(j=0;j<8;j++)
					{
						if(tmp&(0x80>>j))
						{
							OLED_Set_Pixel(x+j, y+i,1);
						}
						else
						{
							OLED_Set_Pixel(x+j, y+i,0);
						}
					}
			}
	}
	else
	{
		return;
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_ShowString(uint8_t x,uint8_t y,uint8_t *chr,uint8_t Char_Size,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display English string
 * @parameters :x:the bebinning x coordinate of the English string
                y:the bebinning y coordinate of the English string
								chr:the start address of the English string
								Char_Size:the size of display character
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/   	  
void GUI_ShowString(uint8_t x,uint8_t y,uint8_t *chr,uint8_t Char_Size,uint8_t mode)
{
	unsigned char j=0,csize;
	if(Char_Size == 16)
  {
	  csize = Char_Size/2;
	}
  else if(Char_Size == 8)
  {
	  csize = Char_Size/2+2;
	}
	else
	{
		return;
	}
	while (chr[j]!='\0')
	{		
		GUI_ShowChar(x,y,chr[j],Char_Size,mode);
		x+=csize;
		if(x>120)
		{
			x=0;
			y+=Char_Size;
		}
		j++;
	}
}
 
/*****************************************************************************
 * @name       :uint32_t mypow(uint8_t m,uint8_t n)
 * @date       :2018-08-27 
 * @function   :get the nth power of m (internal call)
 * @parameters :m:the multiplier
                n:the power
 * @retvalue   :the nth power of m
******************************************************************************/ 
static uint32_t mypow(uint8_t m,uint8_t n)
{
	uint32_t result=1;	 
	while(n--)result*=m;    
	return result;
}
 
/*****************************************************************************
 * @name       :void GUI_ShowNum(uint8_t x,uint8_t y,uint32_t num,uint8_t len,uint8_t Size,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display number
 * @parameters :x:the bebinning x coordinate of the number
                y:the bebinning y coordinate of the number
								num:the number(0~4294967295)
								len:the length of the display number
								Size:the size of display number
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/  			 
void GUI_ShowNum(uint8_t x,uint8_t y,uint32_t num,uint8_t len,uint8_t Size,uint8_t mode)
{         	
	uint8_t t,temp;
	uint8_t enshow=0,csize;
  if(Size == 16)
  {
	  csize = Size/2;
	}
  else if(Size == 8)
  {
	  csize = Size/2+2;
	} 	
	else
	{
		return;
	}
	for(t=0;t<len;t++)
	{
		temp=(num/mypow(10,len-t-1))%10;
		if(enshow==0&&t<(len-1))
		{
			if(temp==0)
			{
				GUI_ShowChar(x+csize*t,y,' ',Size,mode);
				continue;
			}else enshow=1; 
		 	 
		}
	 	GUI_ShowChar(x+csize*t,y,temp+'0',Size,mode); 
	}
}  
 
/*****************************************************************************
 * @name       :void GUI_ShowFont16(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display a single 16x16 Chinese character
 * @parameters :x:the bebinning x coordinate of the Chinese character
                y:the bebinning y coordinate of the Chinese character
								s:the start address of the Chinese character
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/ 
void GUI_ShowFont16(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
{
	uint8_t i,j,k,tmp;
	uint16_t num;
	num = sizeof(cfont16)/sizeof(typFNT_GB16);
  for(i=0;i<num;i++)
	{
		if((cfont16[i].Index[0]==*s)&&(cfont16[i].Index[1]==*(s+1)))
		{
			for(j=0;j<32;j++)
			{
				if(mode)
				{
					tmp = cfont16[i].Msk[j];
				}
				else
				{
					tmp = ~(cfont16[i].Msk[j]);
				}
				for(k=0;k<8;k++)
				{
					if(tmp&(0x80>>k))
					{
						OLED_Set_Pixel(x+(j%2)*8+k, y+j/2,1);
					}
					else
					{
						OLED_Set_Pixel(x+(j%2)*8+k, y+j/2,0);
					}
				}
			}	
			break;
		}	
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_ShowFont24(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display a single 24x24 Chinese character
 * @parameters :x:the bebinning x coordinate of the Chinese character
                y:the bebinning y coordinate of the Chinese character
								s:the start address of the Chinese character
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/ 
void GUI_ShowFont24(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
{
	uint8_t i,j,k,tmp;
	uint16_t num;
	num = sizeof(cfont24)/sizeof(typFNT_GB24);
  for(i=0;i<num;i++)
	{
		if((cfont24[i].Index[0]==*s)&&(cfont24[i].Index[1]==*(s+1)))
		{
			for(j=0;j<72;j++)
			{
				if(mode)
				{
					tmp = cfont24[i].Msk[j];
				}
				else
				{
					tmp = ~(cfont24[i].Msk[j]);
				}
				for(k=0;k<8;k++)
				{
					if(tmp&(0x80>>k))
					{
						OLED_Set_Pixel(x+(j%3)*8+k, y+j/3,1);
					}
					else
					{
						OLED_Set_Pixel(x+(j%3)*8+k, y+j/3,0);
					}
				}
			}	
			break;
		}	
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_ShowFont32(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display a single 32x32 Chinese character
 * @parameters :x:the bebinning x coordinate of the Chinese character
                y:the bebinning y coordinate of the Chinese character
								s:the start address of the Chinese character
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/ 
void GUI_ShowFont32(uint8_t x,uint8_t y,uint8_t *s,uint8_t mode)
{
	uint8_t i,j,k,tmp;
	uint16_t num;
	num = sizeof(cfont32)/sizeof(typFNT_GB32);
  for(i=0;i<num;i++)
	{
		if((cfont32[i].Index[0]==*s)&&(cfont32[i].Index[1]==*(s+1)))
		{
			for(j=0;j<128;j++)
			{
				if(mode)
				{
					tmp = cfont32[i].Msk[j];
				}
				else
				{
					tmp = ~(cfont32[i].Msk[j]);
				}
				for(k=0;k<8;k++)
				{
					if(tmp&(0x80>>k))
					{
						OLED_Set_Pixel(x+(j%4)*8+k, y+j/4,1);
					}
					else
					{
						OLED_Set_Pixel(x+(j%4)*8+k, y+j/4,0);
					}
				}
			}	
			break;
		}	
	}
	OLED_Display();
}
 
/*****************************************************************************
 * @name       :void GUI_ShowCHinese(uint8_t x,uint8_t y,uint8_t hsize,uint8_t *str,uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display Chinese strings
 * @parameters :x:the bebinning x coordinate of the Chinese strings
                y:the bebinning y coordinate of the Chinese strings
								size:the size of Chinese strings
								str:the start address of the Chinese strings
								mode:0-white background and black character
								     1-black background and white character
 * @retvalue   :None
******************************************************************************/	   		   
void GUI_ShowCHinese(uint8_t x,uint8_t y,uint8_t hsize,uint8_t *str,uint8_t mode)
{ 
	while(*str!='\0')
	{
		if(hsize == 16)
		{
			GUI_ShowFont16(x,y,str,mode);
		}
		else if(hsize == 24)
		{
			GUI_ShowFont24(x,y,str,mode);
		}
		else if(hsize == 32)
		{
			GUI_ShowFont32(x,y,str,mode);
		}
		else
		{
			return;
		}
		x+=hsize;
		if(x>WIDTH-hsize)
		{
			x=0;
			y+=hsize;
		}
		str+=2;
	}			
}
 
/*****************************************************************************
 * @name       :void GUI_DrawBMP(uint8_t x,uint8_t y,uint8_t width, uint8_t height, uint8_t BMP[], uint8_t mode)
 * @date       :2018-08-27 
 * @function   :Display a BMP monochromatic picture
 * @parameters :x:the bebinning x coordinate of the BMP monochromatic picture
                y:the bebinning y coordinate of the BMP monochromatic picture
								width:the width of BMP monochromatic picture
								height:the height of BMP monochromatic picture
								BMP:the start address of BMP monochromatic picture array
								mode:0-white background and black character
								     1-black background and white character								
 * @retvalue   :None
******************************************************************************/ 
void GUI_DrawBMP(uint8_t x,uint8_t y,uint8_t width, uint8_t height, uint8_t BMP[], uint8_t mode)
{ 	
 uint8_t i,j,k;
 uint8_t tmp;
 for(i=0;i<height;i++)
 {
		for(j=0;j<(width+7)/8;j++)
		{
		    if(mode)
				{
					tmp = BMP[i*((width+7)/8)+j];
				}
				else
				{
					tmp = ~BMP[i*((width+7)/8)+j];
				}
				for(k=0;k<8;k++)
				{
					if(tmp&(0x80>>k))
					{
						OLED_Set_Pixel(x+j*8+k, y+i,1);
					}
					else
					{
						OLED_Set_Pixel(x+j*8+k, y+i,0);
					}
				}
		}
 } 
 OLED_Display();
}

ath20部分加入之前的代码

运行结果：