中标麒麟6.0双网卡绑定bond0

1.编辑虚拟网络接口配置文件
[root@test~]# more /etc/sysconfig/network-scripts/ifcfg-bond0 
DEVICE=bond0 
IPADDR=172.16.4.100 
NETMASK=255.255.255.0 
GATEWAY=172.16.4.254
ONBOOT=yes


2.编辑各网卡的配置文件，注意编辑之前做好备份工作
[root@test~]# more /etc/sysconfig/network-scripts/ifcfg-eth0 
BOOTPROTO=none 
TYPE=Ethernet 
DEVICE=eth0 
ONBOOT=yes 
MASTER=bond0 
slave=yes 
[root@test ~]# more /etc/sysconfig/network-scripts/ifcfg-eth1 
BOOTPROTO=none 
TYPE=Ethernet 
DEVICE=eth1 
ONBOOT=yes 
MASTER=bond0 
slave=yes
 


3. 中标麒麟6下不再有modprobe.conf这个文件
在/etc/modprobe.d/里建立bond0.conf
在文件中添加
alias bond0 bonding 
options bond0 miimon=100 mode=1
后保存
查看
[root@/]# cat /etc/modprobe.d/bond0.conf
alias bond0 bonding
options bond0 miimon=100 mode=1 


4.在/etc/rc.d/rc.local 加入如下一行 
ifenslave bond0 eth0 eth1
现在的系统可以不写。


5.重新启动系统
6.查看bond0的工作状态
[root@test~]# more /proc/net/bonding/bond0 
Ethernet Channel Bonding Driver: v2.6.1 (October 29, 2004) 


Bonding Mode: load balancing (round-robin) 
MII Status: up 
MII Polling Interval (ms): 100 
Up Delay (ms): 0 
Down Delay (ms): 0 


Slave Interface: eth0 
MII Status: up 
Link Failure Count: 1 
Permanent HW addr: 00:1b:b9:58:8b:b2 


Slave Interface: eth1 
MII Status: down 
Link Failure Count: 0 
Permanent HW addr: 00:07:40:6c:ac:c8


7.查看经过绑定后的网卡工作情况 
[root@test ~]# ifconfig -a 
bond0     Link encap:Ethernet  HWaddr00:1B:B9:58:8B:B2  
         


inet addr:172.16.4.100 Bcast:172.16.4.255  Mask:255.255.255.0 
          inet6 addr:fe80::200:ff:fe00:0/64 Scope:Link 
          UP BROADCAST RUNNINGMASTER MULTICAST  MTU:1500  Metric:1 
          RX packets:744154errors:0 dropped:0 overruns:0 frame:0 
          TX packets:1866915errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0txqueuelen:0 
          RX bytes:1099876146 (1.0GiB)  TX bytes:121233595 (115.6 MiB) 


eth0      Link encap:Ethernet  HWaddr00:1B:B9:58:8B:B2  
          inet6 addr:fe80::21b:b9ff:fe58:8bb2/64 Scope:Link 
          UP BROADCAST RUNNINGSLAVE MULTICAST  MTU:1500  Metric:1 
          RX packets:744154errors:0 dropped:0 overruns:0 frame:0 
          TX packets:1866905errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0txqueuelen:1000 
          RX bytes:1099876146 (1.0GiB)  TX bytes:121232839 (115.6 MiB) 
          Interrupt:9 


eth1      Link encap:Ethernet  HWaddr00:1B:B9:58:8B:B2  
          inet6 addr:fe80::21b:b9ff:fe58:8bb2/64 Scope:Link 
          UP BROADCAST SLAVEMULTICAST  MTU:1500  Metric:1 
          RX packets:0 errors:0dropped:0 overruns:0 frame:0 
          TX packets:10 errors:0dropped:0 overruns:0 carrier:0 
          collisions:0txqueuelen:1000 
          RX bytes:0 (0.0 b) TX bytes:756 (756.0 b) 
          Interrupt:11 Baseaddress:0x1000 


lo        Link encap:Local Loopback  
          inetaddr:127.0.0.1  Mask:255.0.0.0 
          inet6 addr: ::1/128Scope:Host 
          UP LOOPBACKRUNNING  MTU:16436  Metric:1 
          RX packets:2129 errors:0dropped:0 overruns:0 frame:0 
          TX packets:2129 errors:0dropped:0 overruns:0 carrier:0 
          collisions:0txqueuelen:0 
          RX bytes:1998893 (1.9MiB)  TX bytes:1998893 (1.9 MiB) 




附： 
DEVICE=物理设备名 
IPADDR=IP地址 
NETMASK=掩码值 
NETWORK=网络地址 
BROADCAST=广播地址 
GATEWAY=网关地址 
ONBOOT=[yes|no]（引导时是否激活设备） 
USERCTL=[yes|no]（非root用户是否可以控制该设备） 
BOOTPROTO=[none|static|bootp|dhcp]（引导时不使用协议|静态分配|BOOTP协议|DHCP协议） 
HWADDR = 你的MAC地址