新路程------uboot环境变量没生效

    之前刷文件系统一种出错，出错log如下

hisilicon # sf probe 0;mw.b 0x82000000 0xff 0x1800000;tftp 0x82000000 rootfs_ucl
ibc_64k.jffs2;sf erase 0x500000 0x1800000;sf write 0x82000000 0x500000 0x1800000


32768 KiB hi_sfc at 0:0 is now current device
ETH0: PHY(phyaddr=1, rmii) link UP: DUPLEX=FULL : SPEED=100M
MAC:   00-00-23-34-45-66
TFTP from server 192.168.1.1; our IP address is 192.168.1.155
Download Filename 'rootfs_uclibc_64k.jffs2'.
Download to address: 0x82000000
Downloading: #################################################
done
Bytes transferred = 12178136 (b9d2d8 hex)
Erasing at 0x1d00000 -- 100% complete.
Writing at 0x1d00000 -- 100% complete.
hisilicon # saveenv
Saving Environment to SPI Flash...
Erasing SPI flash, offset 0x00080000 size 256K ...done
Writing to SPI flash, offset 0x00080000 size 256K ...done
hisilicon #
hisilicon # bootm
Wrong Image Format for bootm command
ERROR: can't get kernel image!

而且用

reset也一样的错误

结果认真一检查，发现参数不对，没加‘单引号，引以为戒。

本来是这样set bootargs mem=64M console=ttyAMA0,115200n8 mtdparts=hi_sfc:1M(uboot),4M(kernel),24M(root),3M(data) root=/dev/mtdblock2 rootfstype=jffs2

set bootcmd sf probe 0;sf read 0x82000000 0x100000 0x400000\;bootm 0x82000000

现在是

set bootargs 'mem=64M console=ttyAMA0,115200n8 mtdparts=hi_sfc:1M(uboot),4M(kernel),24M(root),3M(data) root=/dev/mtdblock2 rootfstype=jffs2'

set bootcmd 'sf probe 0;sf read 0x82000000 0x100000 0x400000\;bootm 0x82000000'

查看0x82000000地址的内容

hisilicon # md 0x82000000
82000000: 56190527 de38bd8c b46c9e59 a0ca3100    '..V..8.Y.l..1..
82000010: 00800080 00800080 3a4c8930 00020205    ........0.L:....
82000020: 756e694c 2e332d78 35332e34 00000000    Linux-3.4.35....
82000030: 00000000 00000000 00000000 00000000    ................
82000040: e1a00000 e1a00000 e1a00000 e1a00000    ................
82000050: e1a00000 e1a00000 e1a00000 e1a00000    ................
82000060: ea000002 016f2818 00000000 0031caa0    .....(o.......1.
82000070: e1a07001 e1a08002 e10f2000 e3120003    .p....... ......
82000080: 1a000001 e3a00017 ef123456 e10f2000    ........V4... ..
82000090: e38220c0 e121f002 00000000 00000000    . ....!.........
820000a0: e59f47a4 ee110f30 e3800040 ee010f30    .G..0...@...0...
820000b0: eb00005a e28f0f4a e8901c4e e590d01c    Z...J...N.......
820000c0: e0400001 e0866000 e08aa000 e5da9000    ..@..`..........
820000d0: e5dae001 e189940e e5dae002 e5daa003    ................
820000e0: e189980e e1899c0a e08dd000 e28da801    ................
820000f0: e3a05000 e28aa901 e154000a 2a000016    .P........T....*

所以其实问题的关键在于，如果先烧kernel再烧文件系统，虽然已经将文件系统从内存的0x82000000这个地方写到spi flash里了，但是bootm又从0x82000000这个地方启动，本来这里就是文件系统在内存里的位置，当然读不到内核了

所以正确的方式应该是

如果单独烧内核，bootm 0x82000000可以生效

但是如果要烧文件系统，只能reset，因为内存里的0x8200这个地方已经变了