关于ethernet的调试验证总结

需要rndis修改的部分的串口配置

# audio accessory configuration

on property:sys.usb.config=audio_source

write /sys/class/android_usb/android0/enable 0

write /sys/class/android_usb/android0/idVendor 18d1

write /sys/class/android_usb/android0/idProduct 2d02

write /sys/class/android_usb/android0/functions${sys.usb.config}

write /sys/class/android_usb/android0/enable 1

setprop sys.usb.state ${sys.usb.config}

修改之后的串口命令：

在串口下操作一下命令，更换adb模式到rndis模式

cd /sys/class/android_usb/android0/

echo 0 > enable //关闭adb模式

echo 0x1111 > idVender

echo ox2222 > idProduct

echo rndis > funtions

echo 1 > enable

如果在操作的过程中忘记命令，就进入：

vinewton-master/out/target/product/newton/root/init.usn.rc

打开init.usn.rc文件，查看adb的模式设置，然后再操作rndis功能模块。

 

验证的时候需要注意的地方

(1),可能会遇到的情况：

在实际操作的时候会出现ping 板子的IP不能ping通的情况

解决的方法：由于ping得命令是需要经过路由器的，所以，在经过路由器的时候直接就回被路由器截止，所以要验证板子和主机能够形成一个通路的情况就是拔掉网线。当然这个时候可能会出现一种情况是：主机个板子的IP都消失，当然不是真正的消失，此时，需要我们操作的是在root权限下，重新设置IP 主机还有开发板的地址，然后重新验证开发板和主机是否可以正常通信即可。

(2),拔掉网线出现的情况：

root@user-desktop:~# ifconfig

eth0      Linkencap:Ethernet  HWaddr00:e0:4c:68:02:75 

          UPBROADCAST MULTICAST  MTU:1500  Metric:1

          RXpackets:171823 errors:0 dropped:0 overruns:0 frame:0

          TXpackets:224871 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:1000

          RXbytes:54263761 (54.2 MB)  TXbytes:17287411 (17.2 MB)

         Interrupt:41 Base address:0xe000

 

lo        Linkencap:Local Loopback  

          inetaddr:127.0.0.1  Mask:255.0.0.0

          inet6addr: ::1/128 Scope:Host

          UPLOOPBACK RUNNING  MTU:16436  Metric:1

          RXpackets:3139 errors:0 dropped:0 overruns:0 frame:0

          TXpackets:3139 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:0

          RXbytes:233388 (233.3 KB)  TX bytes:233388(233.3 KB)

 

usb0      Linkencap:Ethernet  HWaddrde:dc:b4:f2:06:7e 

          inet6addr: fe80::dcdc:b4ff:fef2:67e/64 Scope:Link

          UPBROADCAST RUNNING MULTICAST MTU:1500  Metric:1

          RXpackets:0 errors:0 dropped:0 overruns:0 frame:0

          TXpackets:0 errors:58 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:1000

          RXbytes:0 (0.0 B)  TX bytes:0 (0.0 B)

解决的方法：

ifconfig eth0192.168.2.66            //配置本机IP

ifconfig usb0192.168.2.220         //配置开发板的IP

配置完IP之后的现实情况：

eth0      Linkencap:Ethernet  HWaddr00:e0:4c:68:02:75 

          inetaddr:192.168.2.66 Bcast:192.168.2.255 Mask:255.255.255.0

          UPBROADCAST MULTICAST  MTU:1500  Metric:1

          RXpackets:171823 errors:0 dropped:0 overruns:0 frame:0

          TXpackets:224871 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:1000

          RXbytes:54263761 (54.2 MB)  TXbytes:17287411 (17.2 MB)

         Interrupt:41 Base address:0xe000

 

lo        Linkencap:Local Loopback 

          inetaddr:127.0.0.1  Mask:255.0.0.0

          inet6addr: ::1/128 Scope:Host

          UPLOOPBACK RUNNING  MTU:16436  Metric:1

          RXpackets:3219 errors:0 dropped:0 overruns:0 frame:0

          TXpackets:3219 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:0

          RXbytes:237996 (237.9 KB)  TX bytes:237996(237.9 KB)

 

usb0      Link encap:Ethernet  HWaddr de:dc:b4:f2:06:7e 

          inetaddr:192.168.2.220 Bcast:192.168.2.255 Mask:255.255.255.0

          inet6addr: fe80::dcdc:b4ff:fef2:67e/64 Scope:Link

          UPBROADCAST RUNNING MULTICAST MTU:1500  Metric:1

          RX packets:0errors:0 dropped:0 overruns:0 frame:0

          TXpackets:0 errors:58 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:1000

          RXbytes:0 (0.0 B)  TX bytes:0 (0.0 B)

验证通信的时候：

root@user-desktop:~# ping 192.168.2.66

PING 192.168.2.66 (192.168.2.66) 56(84) bytes of data.

64 bytes from 192.168.2.66: icmp_req=1 ttl=64time=0.090 ms

64 bytes from 192.168.2.66: icmp_req=2 ttl=64time=0.054 ms

^C

--- 192.168.2.66 ping statistics ---

2 packets transmitted, 2 received, 0% packet loss, time999ms

rtt min/avg/max/mdev = 0.054/0.072/0.090/0.018 ms

root@user-desktop:~# ping 192.168.2.220

PING 192.168.2.220 (192.168.2.220) 56(84) bytes ofdata.

64 bytes from 192.168.2.220: icmp_req=1 ttl=64time=0.079 ms

64 bytes from 192.168.2.220: icmp_req=2 ttl=64time=0.056 ms

64 bytes from 192.168.2.220: icmp_req=3 ttl=64time=0.058 ms

^C

--- 192.168.2.220 ping statistics ---

3 packets transmitted, 3 received, 0% packet loss,time 1998ms

rtt min/avg/max/mdev = 0.056/0.064/0.079/0.012 ms

root@user-desktop:~# ping 192.168.2.222

PING 192.168.2.222 (192.168.2.222) 56(84) bytes ofdata.

From 192.168.2.66 icmp_seq=1 Destination HostUnreachable

From 192.168.2.66 icmp_seq=2 Destination HostUnreachable

From 192.168.2.66 icmp_seq=3 Destination Host Unreachable

^C

--- 192.168.2.222 ping statistics ---

5 packets transmitted, 0 received, +3 errors, 100%packet loss, time 4024ms

pipe 3

 

在验证通信是否正常的时候，只要是数据可以正常实现相应数据即可。

 

(2),让开机自动启动修改的配置文件的信息：

cd /home/hwwei/newton-demo/device/ingenic/newton/config

vi  init.board.usb.rc

添加：

on property:sys.usb.config=rndis,adb

 41     write/sys/class/android_usb/android0/enable 0

 42     write/sys/class/android_usb/android0/idVendor 18d1

 43     write/sys/class/android_usb/android0/idProduct 4ee7

 44     write /sys/class/android_usb/android0/bDeviceClass0

 45     write/sys/class/android_usb/android0/bDeviceSubClass 0

 46     write/sys/class/android_usb/android0/bDeviceProtocol 0

 47     write/sys/class/android_usb/android0/functions ${sys.usb.config}

 48     write /sys/class/android_usb/android0/enable1                                                                                      

 49     start adbd

 50     setprop sys.usb.state ${sys.usb.config}

vi  ../device.mk//添加系统默认属性为rndis

PRODUCT_DEFAULT_PROPERTY_OVERRIDES += \

224    persist.sys.usb.config=rndis

 

cd /home/hwwei/newton-master/out/target/product/newton/root

vi default.prop

将里面的内容修改为：

  1 #

  2 #ADDITIONAL_DEFAULT_PROPERTIES

  3 #

  4 ro.secure=1

  5ro.allow.mock.location=0

  6ro.debuggable=1

  7 persist.sys.usb.config=rndis,adb