stm32 ADC-DMA采集

void bsp_InitADC(void)
{
ADC_InitTypeDef ADC_InitStructure;
ADC_CommonInitTypeDef ADC_CommonInitStructure;
DMA_InitTypeDef DMA_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;

/* 使能 ADC3, DMA2 和 GPIO 时钟 ****************************************/
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2 | RCC_AHB1Periph_GPIOA, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

/* DMA2 Stream0 channel2 配置 **************************************/
DMA_InitStructure.DMA_Channel = DMA_Channel_0;  
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)ADC1_DR_ADDRESS;
DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)ADC256_0;//ADC1ConvertedValue;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
DMA_InitStructure.DMA_BufferSize = 128*3;//1024;//FFT_LENGTH;//(FFT_LENGTH*2);
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable;         
DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init(DMA2_Stream0, &DMA_InitStructure);
	
	
	DMA_ClearFlag(DMA2_Stream0,DMA_IT_TC);
DMA_ITConfig(DMA2_Stream0,DMA_IT_TC,ENABLE); // 中断		
DMA_Cmd(DMA2_Stream0, ENABLE);  

// NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);

// #if 0
/* 配置ADC3通道7引脚为模拟输入模式,PA5 huxi******************************/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//#endif

/* 配置ADC3通道7引脚为模拟输入模式******************************/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOA, &GPIO_InitStructure);
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOA, &GPIO_InitStructure);

/****************************************************************************   
  PCLK2 = HCLK / 2 
  下面选择的是2分频
  ADCCLK = PCLK2 /2 = HCLK / 4 = 168 / 4 = 42M
  ADC采样频率： Sampling Time + Conversion Time = 3 + 12 cycles = 15cyc
                Conversion Time = 42MHz / 15cyc = 2.8Mbps. 
*****************************************************************************/
/* ADC公共部分初始化**********************************************************/
ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
ADC_CommonInit(&ADC_CommonInitStructure);

/* ADC1 初始化 ****************************************************************/
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
ADC_InitStructure.ADC_ScanConvMode = ENABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_Rising;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC3;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfConversion = 3;//2
ADC_Init(ADC1, &ADC_InitStructure);
	
	/* ADC1 规则 channel5 配置 *************************************/
ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 1, ADC_SampleTime_3Cycles);    
	//#if 0
/* ADC1 规则 channel6 配置 *************************************/
ADC_RegularChannelConfig(ADC1, ADC_Channel_5, 2, ADC_SampleTime_3Cycles);
	
	    /* ADC1 规则通道18 (VBAT) 配置 ----------------------------------------------*/
ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 3, ADC_SampleTime_3Cycles);

/* 使能 VBAT 通道 */

// ADC_VBATCmd(ENABLE);

	//#endif
/* 使能DMA请求(单ADC模式) */
ADC_DMARequestAfterLastTransferCmd(ADC1, ENABLE);

/* 使能 ADC1 DMA */
ADC_DMACmd(ADC1, ENABLE);

/* 使能 ADC1 */
ADC_Cmd(ADC1, ENABLE);

/* 软件启动ADC1 -------------------------------------------------------------*/
ADC_SoftwareStartConv(ADC1);

TIM1_Config();
	
	NVIC_InitStructure.NVIC_IRQChannel = DMA2_Stream0_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);

}

本段代码是利用一个ADC通道采集三路模拟信号的代码设计。利用DMA存储数据。