sina33打开spi0dev0.0、spi1dev1.0的步骤.txt（全志a33下生成设备节点/dev/spi0dev0.0、/dev/spi1dev1.0）

sina33打开spi0dev0.0/spi1dev1.0的步骤.txt
sina33打开spi0dev0.0、spi1dev1.0的步骤.txt


（全志a33下生成设备节点/dev/spi0dev0.0、/dev/spi1dev1.0）


0、
S:\lichee\tools\pack\chips\sun8iw5p1\configs\default\env.cfg
bootdelay=0
修改为
bootdelay=3
方便按 enter 进u-boot，进行调试。








1、
rootroot@rootroot-E400:~/wyb/sina33/lichee/linux-3.4$ 
rootroot@rootroot-E400:~/wyb/sina33/lichee/linux-3.4$ make ARCH=arm menuconfig
（sina33的原始menuconfig）
Device Drivers --->
[*] SPI support --->
--- SPI support
[ ]   Debug support for SPI drivers
     *** SPI Master Controller Drivers ***
< >   Altera SPI Controller
< >   Utilities for Bitbanging SPI masters
< >   GPIO-based bitbanging SPI Master
< >   OpenCores tiny SPI
<*>   SUNXI SPI Controller
< >   Xilinx SPI controller common module
< >   DesignWare SPI controller core support
     *** SPI Protocol Masters ***
< >   User mode SPI device driver support
< >   Infineon TLE62X0 (for power switching)








（sina33的修改menuconfig）
Device Drivers --->
[*] SPI support --->
--- SPI support
[ ]   Debug support for SPI drivers
     *** SPI Master Controller Drivers ***
< >   Altera SPI Controller
< >   Utilities for Bitbanging SPI masters
< >   GPIO-based bitbanging SPI Master
< >   OpenCores tiny SPI
<*>   SUNXI SPI Controller
< >   Xilinx SPI controller common module
< >   DesignWare SPI controller core support
     *** SPI Protocol Masters ***
（需要打开这里才能够生成设备节点：/dev/spi0dev0.0、/dev/spi1dev1.0）
<*>   User mode SPI device driver support
< >   Infineon TLE62X0 (for power switching)










2、
S:\lichee\tools\pack\chips\sun8iw5p1\configs\y3\sys_config.fex


;----------------------------------------------------------------------------------
;SPI controller configuration
;spi_used       = SPIx enable
;spi_cs_bitmap  = SPI bit mapping
;----------------------------------------------------------------------------------
[spi0]
spi_used       = 1
spi_cs_bitmap  = 1
spi_mosi       = port:PC00<3><default><default><default>
spi_miso       = port:PC01<3><default><default><default>
spi_sclk       = port:PC02<3><default><default><default>
spi_cs0        = port:PC03<3><1><default><default>


[spi1]
spi_used       = 1
spi_cs_bitmap  = 1
spi_cs0        = port:PA00<2><1><default><default>
spi_sclk       = port:PA01<2><default><default><default>
spi_mosi       = port:PA02<2><default><default><default>
spi_miso       = port:PA03<2><default><default><default>


;----------------------------------------------------------------------------------
;SPI device configuration
;spi_dev_num: number of spi devices
;----------------------------------------------------------------------------------
[spi_devices]
（数量2表示生成2个SPI设备节点：/dev/spi0dev0.0、/dev/spi1dev1.0）
spi_dev_num = 2


;----------------------------------------------------------------------------------
;[spi_board0] spi device configuration
;modalias      = spi device name
;max_speed_hz  = max transfer speed
;bus_num       = bus ID
;chip_select   = chip select, 0,1
;mode          = SPI transfer mode
;----------------------------------------------------------------------------------
[spi_board0]
;modalias      = "at25df641"
modalias      = "spi0dev"
max_speed_hz  = 50000000
bus_num       = 0
chip_select   = 0
mode          = 0


[spi_board1]
;modalias      = "at25df641"
modalias      = "spi1dev"
max_speed_hz  = 50000000
（！！！！请严重注意，总线变了，这里需要修改，否则出错！进不了spi1dev_probe）
bus_num       = 1
chip_select   = 0
mode          = 0








（引脚复用PC00、PC01、PC02、PC03，将来调试功能的时候可能会出错！！！！）
;----------------------------------------------------------------------------------
;[nandx_para]
;nand_support_2ch    = support dual channel
;nand0_used          = nand0使能标识
;----------------------------------------------------------------------------------
[nand0_para]
nand_support_2ch    = 0


nand0_used          = 0
;nand0_we            = port:PC00<2><default><default><default>
;nand0_ale           = port:PC01<2><default><default><default>
;nand0_cle           = port:PC02<2><default><default><default>
;nand0_ce1           = port:PC03<2><default><default><default>
nand0_ce0           = port:PC04<2><default><default><default>
nand0_nre           = port:PC05<2><default><default><default>
nand0_rb0           = port:PC06<2><default><default><default>
nand0_rb1           = port:PC07<2><default><default><default>
nand0_d0            = port:PC08<2><default><default><default>
nand0_d1            = port:PC09<2><default><default><default>
nand0_d2            = port:PC10<2><default><default><default>
nand0_d3            = port:PC11<2><default><default><default>
nand0_d4            = port:PC12<2><default><default><default>
nand0_d5            = port:PC13<2><default><default><default>
nand0_d6            = port:PC14<2><default><default><default>
nand0_d7            = port:PC15<2><default><default><default>
nand0_ndqs          = port:PC16<2><default><default><default>
nand0_ce2           = port:PC17<2><default><default><default>
nand0_ce3           = port:PC18<2><default><default><default>








（引脚复用PA01、PA02，将来调试功能的时候可能会出错！！！！）
;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used        = 1
Vdevice_0           = port:PA01<5><1><2><default>
Vdevice_1           = port:PA02<5><1><2><default>








3、
将S:\lichee\linux-3.4\drivers\spi\spidev.c
修改替换成 spi0dev.c、spi1dev.c


编译成模块：spi0dev.ko、spi1dev.ko，插入即可在串口中看见设备节点：spi0dev0.0、spi1dev1.0。


crw------- root     root     254,   0 1970-01-01 08:03 rtc0
crw-rw---- keystore keystore  10, 111 1970-01-01 08:03 scdev
drwxr-xr-x root     root              1970-01-01 08:03 snd
drwxr-xr-x root     root              1970-01-02 08:01 socket
crw------- root     root     155,   0 1970-01-02 08:04 spi0dev0.0
crw------- root     root     157,   0 1970-01-02 08:04 spi1dev1.0
crw------- root     root      10,  60 1970-01-01 08:03 sunxi-reg
crw------- root     root     252,   0 1970-01-01 08:03 sunxi_pwm
crw------- root     root      10,  58 1970-01-01 08:03 sw_sync

crw-rw-rw- root     root       5,   0 1970-01-01 08:03 tty

改动的文件（带目录结构）的下载链接：
http://download.csdn.net/detail/wb4916/8789897
sina33备份的文件20150609_2100.7z