ise+13.4+证书+linux,usb-driver: xilinx usb cable driver under linux for ISE 14.7

This library emulates Jungo Windrvr USB and parallel port functions in

userspace which are required by XILINX impact to access the Platform cable USB

and Parallel Cable III.

With this library it is possible to access the cables without loading a

proprietary kernel module which breaks with every new kernel release. It uses

the functionality provided by the libusb userspace library for USB access and

the kernel interface at /dev/parport0 for parallel port access instead and

should work on every kernel version which is supported by libusb and supports

ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with

the following software:

* ISE 14.7

* ISE 13.1

* ISE 12.1

* ISE Webpack 11.1

* ISE Webpack 10.1

* ISE Webpack 9.2SP1, SP2, SP3, SP4

* ISE Webpack 9.1SP1, SP2, SP3

* ISE Webpack 8.2SP3

* ISE Webpack 8.1SP3

* ChipScope 10.1

* ChipScope 9.2.01i, 9.2.02i, 9.2.03i, 9.2.04i

* ChipScope 9.1.02i, 9.1.03i

* ChipScope 8.2.04i

* EDK 10.1

* EDK 9.2.01i, 9.2.02i

* EDK 9.1.01i, 9.1.02i

* EDK 8.2.02i

* EDK 8.1.02i

* Synplicity Identify

In addition to the XILINX USB and parallel cables, devices based on the FTDI

2232 serial converter chip are also experimentally supported. This includes

devices like the Amontec JTAGkey(-Tiny).

Build the library by calling `make'. If you are on a 64 bit system but want

to build a 32 bit library, run `make lib32' instead. Be sure to have the 32

bit versions of libusb-devel and libftdi-devel installed!

To use this library you have to preload the library before starting impact:

$ LD_PRELOAD=/path/to/libusb-driver.so impact

or

$ export LD_PRELOAD=/path/to/libusb-driver.so (for sh shells)

$ setenv LD_PRELOAD /path/to/libusb-driver.so (for csh shells)

$ impact

The source for this library can be found at:

http://git.zerfleddert.de/cgi-bin/gitweb.cgi/usb-driver or

https://gitee.com/fsfzp888/usb-driver

The main website is located at:

http://www.rmdir.de/~michael/xilinx/

The Git repository can be cloned with:

git clone git://git.zerfleddert.de/usb-driver or

git clone https://gitee.com/fsfzp888/usb-driver.git

Notes for the USB cable

=======================

To use the device as an ordinary user, put the following line in a new

file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:

ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="03fd", MODE="666"

If your cable does not have the ID 03fd:0008 in the output of lsusb,

the initial firmware has not been loaded (loading it changes the

product-ID from another value to 8). To load the firmware follow

these steps:

1. Run ./setup_pcusb in this directory, this should set up everything

correctly:

- When $XILINX is set correctly:

$ ./setup_pcusb

- When $XILINX is not set, and ISE is installed in /opt/Xilinx/13.1:

$ ./setup_pcusb /opt/Xilinx/13.1/ISE_DS/ISE

Old instructions, use only when the above script did not work:

1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from

/path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules

2. If you are running a newer version of udev (as in Debian Squeeze and

Ubuntu 9.10), you need to adapt the rules-file to the new udev-version:

sed -i -e 's/TEMPNODE/tempnode/' -e 's/SYSFS/ATTRS/g' -e 's/BUS/SUBSYSTEMS/' /etc/udev/rules.d/xusbdfwu.rules

3. Install the package containing /sbin/fxload from your linux distribution.

It is usually called "fxload"

4. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/

5. restart udev and re-plug the cable

If you have multiple cables connected, you can specify the cable to use

in the XILINX_USB_DEV environment-variable as "bus:device".

These identifiers are available in the output of lsusb:

Bus 001 Device 004: ID 03fd:0008 Xilinx, Inc.

^^^ ^^^

To use this cable, set the XILINX_USB_DEV variable to "001:004".

Notes for the parallel cable

============================

To access the parallel port from userspace, the kernel needs to be built with

the features "Parallel port support" (CONFIG_PARPORT), "PC-style hardware"

(CONFIG_PARPORT_PC) and "Support for user-space parallel port device drivers"

(CONFIG_PPDEV) builtin or as modules. If these features are built as modules,

they need to be loaded before using this library.

These modules are called:

parport

parport_pc

ppdev

To use the device as an ordinary user, put the user in the group 'lp'

If you have an almost compatible cable which works with other software but not

with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.

This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.

Parallel Cable IV is currently only supported in 'compatibility mode', as no

attempt to configure the ECP registers is done by this library.

If you get "Programming failed" or "DONE did not go high" when programming

through the parallel cable with Impact 9.1, make sure to have the option "Use

HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration

Preferences.

If you are using batch mode, add the following line to your cmd file:

setPreference -pref UseHighz:TRUE

(This problem also occurs on windows and when using the real windrvr in linux

and is solved with the same workaround. Impact 8.2 is working fine with the same

boards and designs)

Notes for FTDI 2232 based cables

================================

To build the driver with FTDI 2232 support, you need to have libftdi and

the libftdi development package installed. On debian, you can install both

by installing 'libftdi-dev'.

To set-up the device:

1. Find out the vendor and product id of your cable using lsusb:

Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...

~~~~~~~~~

2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace

the vendor and product-id in the example file with the values provided in

the lsusb-output. You can also change the 'parallel port' which is mapped to

this cable. Impact sees the device at that port as a Parallel Cable III.

3. To use the device as an ordinary user, put the following line in a new file

in /etc/udev/rules.d/ and restart udev:

ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="cff8", MODE="666"

(replace the vendor and product id with your values)

The support for FTDI 2232 based devices is experimental and they are currently

significantly slower than the other supported cables.

Locked cables

=============

If you get the message 'The cable is being used by another application.' from

impact, try running the following command:

echo -e 'cleancablelock\nexit' | impact -batch

附：

ubuntu安装ISE 14.7方法

从官网下载linux 64位版本的xilinx ISE 14.7 or 到http://pan.baidu.com/s/1pL6Uyq3 下载

sudo tar -xvf Xilinx_ISE_DS_14.7_1015_1.tar -C /opt

不使用root权限安装

. /opt/Xilinx_ISE_DS_14.7_1015_1/xsetup

然后图形界面安装，不要选择安装cable driver。选择目录在/home//， 安装完成后，

source /home//14.7/ISE_DS/settings64.sh

然后

. /home//14.7/ISE_DS/ISE/bin/lin64/ise

选择license manager 选择license文件即可，不source 配置shell会导致license manager 无法打开，点击没有反应。

书写如下启动脚本文件：

#############################################################

#!/bin/bash

ISE_DS_DIR=/home//14.7/ISE_DS

export gmake=/usr/bin/make

cd "$ISE_DS_DIR"

source "$ISE_DS_DIR"/settings64.sh

#export LANG='' # reset locale to English to fix decimal/comma seperation

"$ISE_DS_DIR"/ISE/bin/lin64/ise

#############################################################

在/usr/share/applications/目录下创建ISE.desktop，内容如下：

#############################################################

[Desktop Entry]

Version=1.0

Name=Xilinx ISE

Comment=Xilinx ISE 14.7

Exec=/home//14.7/ise

Icon=/home//14.7/ISE_DS/ISE/data/images/pn-ise.png

StartupNotify=true

Type=Application

Categories=Application;

#############################################################

然后把该快捷方式复制到桌面即可直接点击启动ISE。

参考http://www.george-smart.co.uk/wiki/Xilinx_JTAG_Linux

sudo apt-get install gitk git-gui libusb-dev build-essential libc6-dev-i386 fxload

cd /home//14.7

git clone https://gitee.com/fsfzp888/usb-driver.git

cd usb-driver

make

./setup_pcusb /home//14.7/ISE_DS/ISE