![](http://hi.csdn.net/attachment/201112/17/0_13241139209QM8.gif)
1.Device Drivers ---> Character devices ---> Serial drivers ---> <*> Samsung Soc Serial support
obj-$(CONFIG_SERIAL_CORE) += serial_core.o 是串口核心
obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o 是串口具体实现
2.控制台终端
计算机显示器通常被称为控制台终端(console)。必须有一个(些)特殊文件与console相关联,比如虚拟终端tty1 tty2 串口ttySAC0 ttySAC1等。系统所发出的信息会发送到console对应的文件上。
如果不选此项,在启动kernel后就不输出了。
Starting kernel ...
Uncompressing Linux......................................................................................................................................
................... done, booting the kernel.
uboot里设置的 console=ttySAC0 ,决定了使用ttySAC0作控制台终端。在samsung.c中实现console。
/* s3c24xx_serial_initconsole
*
* initialise the console from one of the uart drivers
*/
static struct console s3c24xx_serial_console = {
.name = S3C24XX_SERIAL_NAME,
.device = uart_console_device,
.flags = CON_PRINTBUFFER,
.index = -1,
.write = s3c24xx_serial_console_write,
.setup = s3c24xx_serial_console_setup
};
int s3c24xx_serial_initconsole(struct platform_driver *drv,
struct s3c24xx_uart_info *info)
{
struct platform_device *dev = s3c24xx_uart_devs[0];
dbg("s3c24xx_serial_initconsole\n");
/* select driver based on the cpu */
if (dev == NULL) {
printk(KERN_ERR "s3c24xx: no devices for console init\n");
return 0;
}
if (strcmp(dev->name, drv->driver.name) != 0)
return 0;
s3c24xx_serial_console.data = &s3c24xx_uart_drv;
s3c24xx_serial_init_ports(info);
register_console(&s3c24xx_serial_console);
return 0;
}
3. <*> Samsung S3C2440/S3C2442 Serial port support
普通串口 /dev/ttySAC*
obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
1.串口的平台设备分散在mach-mini2440.c,arch/arm/plat-s3c/init.c等,在系统启动时注册.比如mach-mini2440.c
static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
[0] = {//串口0
.hwport = 0,
.flags = 0,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
},
[1] = {//串口1
.hwport = 1,
.flags = 0,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
},
[2] = {//串口2
.hwport = 2,
.flags = 0,
.ucon = 0x3c5,
.ulcon = 0x03,
.ufcon = 0x51,
}
};
比如
init.cvoid __init s3c24xx_init_uartdevs(char *name,
struct s3c24xx_uart_resources *res,
struct s3c2410_uartcfg *cfg, int no)
{
struct platform_device *platdev;
struct s3c2410_uartcfg *cfgptr = uart_cfgs;
struct s3c24xx_uart_resources *resp;
int uart;
memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no);
for (uart = 0; uart < no; uart++, cfg++, cfgptr++) {
platdev = s3c24xx_uart_src[cfgptr->hwport];
resp = res + cfgptr->hwport;
s3c24xx_uart_devs[uart] = platdev;
platdev->name = name;
platdev->resource = resp->resources;
platdev->num_resources = resp->nr_resources;
platdev->dev.platform_data = cfgptr;
}
nr_uarts = no;
}
2.串口的平台驱动在
arch/arm/mach-s3c2440/s3c2440.c和samsung.c
初始化:
s3c2440.c初始化时注册了平台驱动
static int __init s3c2440_serial_init(void)
{
return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf);//见下面
}
static void __exit s3c2440_serial_exit(void)
{
platform_driver_unregister(&s3c2440_serial_driver);
}
module_init(s3c2440_serial_init);
module_exit(s3c2440_serial_exit);
//samsung.c
int s3c24xx_serial_init(struct platform_driver *drv,
struct s3c24xx_uart_info *info)
{
dbg("s3c24xx_serial_init(%p,%p)\n", drv, info);
#ifdef CONFIG_PM
drv->suspend = s3c24xx_serial_suspend;
drv->resume = s3c24xx_serial_resume;
#endif
return platform_driver_register(drv);
}
samsung.c在初始化时就注册了串口驱动
static int __init s3c24xx_serial_modinit(void)
{
int ret;
ret = uart_register_driver(&s3c24xx_uart_drv);
if (ret < 0) {
printk(KERN_ERR "failed to register UART driver\n");
return -1;
}
return 0;
}
static void __exit s3c24xx_serial_modexit(void)
{
uart_unregister_driver(&s3c24xx_uart_drv);
}
module_init(s3c24xx_serial_modinit);
module_exit(s3c24xx_serial_modexit);
看一下平台驱动的probe,可知是在probe函数里面添加串口
s3c2440.c
static struct s3c24xx_uart_info s3c2440_uart_inf = {
.name = "Samsung S3C2440 UART",
.type = PORT_S3C2440,
.fifosize = 64,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.get_clksrc = s3c2440_serial_getsource,
.set_clksrc = s3c2440_serial_setsource,
.reset_port = s3c2440_serial_resetport,
};
/* device management */
static int s3c2440_serial_probe(struct platform_device *dev)
{
dbg("s3c2440_serial_probe: dev=%p\n", dev);
return s3c24xx_serial_probe(dev, &s3c2440_uart_inf);//见下面
}
//samsung.c
static int probe_index;
int s3c24xx_serial_probe(struct platform_device *dev,
struct s3c24xx_uart_info *info)
{
struct s3c24xx_uart_port *ourport;
int ret;
dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index);
ourport = &s3c24xx_serial_ports[probe_index];
probe_index++;
dbg("%s: initialising port %p...\n", __func__, ourport);
ret = s3c24xx_serial_init_port(ourport, info, dev);
if (ret < 0)
goto probe_err;
dbg("%s: adding port\n", __func__);
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
platform_set_drvdata(dev, &ourport->port);
ret = device_create_file(&dev->dev, &dev_attr_clock_source);
if (ret < 0)
printk(KERN_ERR "%s: failed to add clksrc attr.\n", __func__);
ret = s3c24xx_serial_cpufreq_register(ourport);
if (ret < 0)
dev_err(&dev->dev, "failed to add cpufreq notifier\n");
return 0;
probe_err:
return ret;
}
几个重要的结构体
//uart_ops
static struct uart_ops s3c24xx_serial_ops = {
.pm = s3c24xx_serial_pm,
.tx_empty = s3c24xx_serial_tx_empty,
.get_mctrl = s3c24xx_serial_get_mctrl,
.set_mctrl = s3c24xx_serial_set_mctrl,
.stop_tx = s3c24xx_serial_stop_tx,
.start_tx = s3c24xx_serial_start_tx,
.stop_rx = s3c24xx_serial_stop_rx,
.enable_ms = s3c24xx_serial_enable_ms,
.break_ctl = s3c24xx_serial_break_ctl,
.startup = s3c24xx_serial_startup,
.shutdown = s3c24xx_serial_shutdown,
.set_termios = s3c24xx_serial_set_termios,
.type = s3c24xx_serial_type,
.release_port = s3c24xx_serial_release_port,
.request_port = s3c24xx_serial_request_port,
.config_port = s3c24xx_serial_config_port,
.verify_port = s3c24xx_serial_verify_port,
};
//uart_driver
static struct uart_driver s3c24xx_uart_drv = {
.owner = THIS_MODULE,
.dev_name = "s3c2410_serial",
.nr = CONFIG_SERIAL_SAMSUNG_UARTS,
.cons = S3C24XX_SERIAL_CONSOLE,
.driver_name = S3C24XX_SERIAL_NAME,
.major = S3C24XX_SERIAL_MAJOR,
.minor = S3C24XX_SERIAL_MINOR,
};
//s3c24xx_uart_port
static struct s3c24xx_uart_port s3c24xx_serial_ports[CONFIG_SERIAL_SAMSUNG_UARTS] = {
[0] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX0,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 0,
}
},
[1] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX1,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 1,
}
},
#if CONFIG_SERIAL_SAMSUNG_UARTS > 2
[2] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX2,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 2,
}
},
#endif
#if CONFIG_SERIAL_SAMSUNG_UARTS > 3
[3] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[3].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX3,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 3,
}
}
#endif
};
//serial_core.h
struct uart_port {
spinlock_t lock; /* port lock */
unsigned long iobase; /* in/out[bwl] */
unsigned char __iomem *membase; /* read/write[bwl] */
unsigned int (*serial_in)(struct uart_port *, int);
void (*serial_out)(struct uart_port *, int, int);
unsigned int irq; /* irq number */
unsigned long irqflags; /* irq flags */
unsigned int uartclk; /* base uart clock */
unsigned int fifosize; /* tx fifo size */
unsigned char x_char; /* xon/xoff char */
unsigned char regshift; /* reg offset shift */
unsigned char iotype; /* io access style */
unsigned char unused1;
#define UPIO_PORT (0)
#define UPIO_HUB6 (1)
#define UPIO_MEM (2)
#define UPIO_MEM32 (3)
#define UPIO_AU (4) /* Au1x00 type IO */
#define UPIO_TSI (5) /* Tsi108/109 type IO */
#define UPIO_DWAPB (6) /* DesignWare APB UART */
#define UPIO_RM9000 (7) /* RM9000 type IO */
unsigned int read_status_mask; /* driver specific */
unsigned int ignore_status_mask; /* driver specific */
struct uart_state *state; /* pointer to parent state */
struct uart_icount icount; /* statistics */
struct console *cons; /* struct console, if any */
#if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(SUPPORT_SYSRQ)
unsigned long sysrq; /* sysrq timeout */
#endif
upf_t flags;
#define UPF_FOURPORT ((__force upf_t) (1 << 1))
#define UPF_SAK ((__force upf_t) (1 << 2))
#define UPF_SPD_MASK ((__force upf_t) (0x1030))
#define UPF_SPD_HI ((__force upf_t) (0x0010))
#define UPF_SPD_VHI ((__force upf_t) (0x0020))
#define UPF_SPD_CUST ((__force upf_t) (0x0030))
#define UPF_SPD_SHI ((__force upf_t) (0x1000))
#define UPF_SPD_WARP ((__force upf_t) (0x1010))
#define UPF_SKIP_TEST ((__force upf_t) (1 << 6))
#define UPF_AUTO_IRQ ((__force upf_t) (1 << 7))
#define UPF_HARDPPS_CD ((__force upf_t) (1 << 11))
#define UPF_LOW_LATENCY ((__force upf_t) (1 << 13))
#define UPF_BUGGY_UART ((__force upf_t) (1 << 14))
#define UPF_NO_TXEN_TEST ((__force upf_t) (1 << 15))
#define UPF_MAGIC_MULTIPLIER ((__force upf_t) (1 << 16))
#define UPF_CONS_FLOW ((__force upf_t) (1 << 23))
#define UPF_SHARE_IRQ ((__force upf_t) (1 << 24))
/* The exact UART type is known and should not be probed. */
#define UPF_FIXED_TYPE ((__force upf_t) (1 << 27))
#define UPF_BOOT_AUTOCONF ((__force upf_t) (1 << 28))
#define UPF_FIXED_PORT ((__force upf_t) (1 << 29))
#define UPF_DEAD ((__force upf_t) (1 << 30))
#define UPF_IOREMAP ((__force upf_t) (1 << 31))
#define UPF_CHANGE_MASK ((__force upf_t) (0x17fff))
#define UPF_USR_MASK ((__force upf_t) (UPF_SPD_MASK|UPF_LOW_LATENCY))
unsigned int mctrl; /* current modem ctrl settings */
unsigned int timeout; /* character-based timeout */
unsigned int type; /* port type */
const struct uart_ops *ops;
unsigned int custom_divisor;
unsigned int line; /* port index */
resource_size_t mapbase; /* for ioremap */
struct device *dev; /* parent device */
unsigned char hub6; /* this should be in the 8250 driver */
unsigned char suspended;
unsigned char unused[2];
void *private_data; /* generic platform data pointer */
};
在probe中(s3c24xx_serial_probe(),samsung.c)用uart_add_one_port()将uart_port加入uart_driver
每一uart_port对应一个uart_ops,主要工作就是实现这些函数指针。