FPGA Prototyping By Verilog Examples第五章 状态机FSM设计

上升沿检测电路之Moore型FSM

// Listing 5.3
module edge_detect_moore
   (
    input wire clk, reset,
    input wire level,
    output reg tick
   );

   // symbolic state declaration
   localparam [1:0]
      zero = 2'b00,
      edg = 2'b01,
      one = 2'b10;

   // signal declaration
   reg [1:0] state_reg, state_next;

   // state register
    always @(posedge clk, posedge reset)
       if (reset)
          state_reg <= zero;
       else
          state_reg <= state_next;

   // next-state logic and output logic
   always @*
   begin
      state_next = state_reg;  // default state: the same
      tick = 1'b0;             // default output: 0
      case (state_reg)
         zero:
            if (level)
               state_next = edg;
         edg:
            begin
               tick = 1'b1;
               if (level)
                  state_next = one;
               else
                  state_next = zero;
             end
         one:
            if (~level)
               state_next = zero;
         default: state_next = zero;
      endcase
   end
endmodule

上升沿检测电路之Mealy型FSM

// Listing 5.4
module edge_detect_mealy
   (
    input wire  clk, reset,
    input wire  level,
    output reg tick
   );

   // symbolic state declaration
   localparam zero = 1'b0,
               one = 1'b1;

   // signal declaration
   reg state_reg, state_next;

   // state register
    always @(posedge clk, posedge reset)
       if (reset)
          state_reg <= zero;
       else
          state_reg <= state_next;

   // next-state logic and output logic
   always @*
   begin
      state_next = state_reg;  // default state: the same
      tick = 1'b0;             // default output: 0
      case (state_reg)
         zero:
            if (level)
               begin
                  tick = 1'b1;
                  state_next = one;
               end
         one:
            if (~level)
               state_next = zero;
         default: state_next = zero;
      endcase
   end

endmodule

上升沿检测电路之基本门电路设计

// Listing 5.5
module edge_detect_gate
   (
    input wire  clk, reset,
    input wire  level,
    output wire tick
   );

   // signal declaration
   reg delay_reg;

   // delay register
    always @(posedge clk, posedge reset)
       if (reset)
          delay_reg <= 1'b0;
       else
          delay_reg <= level;

   // decoding logic
   assign tick = ~delay_reg & level;

endmodule

按键消抖电路FSM

// Listing 5.6
module db_fsm
   (
    input wire clk, reset,
    input wire sw,
    output reg db
   );

   // symbolic state declaration
   localparam  [2:0]
               zero    = 3'b000,
               wait1_1 = 3'b001,
               wait1_2 = 3'b010,
               wait1_3 = 3'b011,
               one     = 3'b100,
               wait0_1 = 3'b101,
               wait0_2 = 3'b110,
               wait0_3 = 3'b111;

   // number of counter bits (2^N * 20ns = 10ms tick)
   localparam N =19;

   // signal declaration
   reg [N-1:0] q_reg;
   wire [N-1:0] q_next;
   wire m_tick;
   reg [2:0] state_reg, state_next;

   // body

   //=============================================
   // counter to generate 10 ms tick
   //=============================================
   always @(posedge clk)
      q_reg <= q_next;
   // next-state logic
   assign q_next = q_reg + 1;
   // output tick
   assign m_tick = (q_reg==0) ? 1'b1 : 1'b0;

   //=============================================
   // debouncing FSM
   //=============================================
   // state register
    always @(posedge clk, posedge reset)
       if (reset)
          state_reg <= zero;
       else
          state_reg <= state_next;

   // next-state logic and output logic
   always @*
   begin
      state_next = state_reg;  // default state: the same
      db = 1'b0;               // default output: 0
      case (state_reg)
         zero:
            if (sw)
               state_next = wait1_1;
         wait1_1:
            if (~sw)
               state_next = zero;
            else
               if (m_tick)
                  state_next = wait1_2;
         wait1_2:
            if (~sw)
               state_next = zero;
            else
               if (m_tick)
                  state_next = wait1_3;
         wait1_3:
            if (~sw)
               state_next = zero;
            else
               if (m_tick)
                  state_next = one;
         one:
            begin
              db = 1'b1;
              if (~sw)
                 state_next = wait0_1;
            end
         wait0_1:
            begin
               db = 1'b1;
               if (sw)
                  state_next = one;
               else
                 if (m_tick)
                    state_next = wait0_2;
            end
         wait0_2:
            begin
               db = 1'b1;
               if (sw)
                  state_next = one;
               else
                 if (m_tick)
                    state_next = wait0_3;
            end
         wait0_3:
            begin
               db = 1'b1;
               if (sw)
                  state_next = one;
               else
                 if (m_tick)
                    state_next = zero;
            end
         default: state_next = zero;
      endcase
   end

endmodule

路漫漫其修远兮，吾将上下而求索

转载自：http://www.cnblogs.com/qiweiwang/archive/2011/04/12/2013415.html

转载于:https://www.cnblogs.com/chengqi521/p/6684565.html