skew width_SKEW WIDTH是什么意思

1. SKEW WIDTH是什么意思

1. The method controls the move of head flying over the disk by firmware and analyzes the width change of projection of the read head, write head and erase band. The experiment shows skew angel can change off-track capability of magnetic head and change the radial error propagation of radial error of self servo-writing.

分离式磁头对硬盘驱动器伺服信息自刻写的影响同样不容忽视，为此提出了一种测定磁头偏移磁道能力大小的方法：通过控制磁头飞行过程，并在飞行过程中动态获取读头信号幅度和比特误差率，从而获取磁头磁道偏移能力。

2. The influence to stress of skew arch bridge was studied by changing the abutment torsional stiffness and width-span ratio.

通过改变桥台抗扭刚度和宽跨比，研究对斜交拱桥受力的影响。

3. Taking EMG function as a mode! of skewed chromatographic peak, a set of sequential equations which can be used to ca'culare the model parameters from skew index (D) and so called " half-width rule " of a column system were developed.

本文以EMG分布函数作为色谱峰的数学模型，提出由柱系统的半峰宽规律与峰态偏斜度D计算EMG参数的连环公式，用于快速谱图拟合和重叠峰分解。

4. By comparing and analyzing the measured water level, three-dimensional velocity distribution and turbulent character around the bridge location, the calculation method for the backwater of skew bridges is improved and the reduction factor of block water width is presented.

通过对桥位附近的实测水位与水流三维流速分布及紊动特性的比较分析，改进了计算斜交桥壅水的方法，并给出阻水宽度折算系数。

5. TORSIONAL RIGIDITY OF UNDER-REINFORCED CONCRETE SLABS On the Influence of Abutment Torsional Stiffness and Width-span Ratio to the Stress of Skew Arch Bridge

钢筋混凝土适筋板式构件的抗扭刚度桥台抗扭刚度及宽跨比对斜交拱桥受力的影响

6. Based on the fact that the skew roll groove width is same in rolling steel sashes of 3205 series, a metal transfer formula was deduced between leg and web during plastic deformation.

本文以轧制3205型窗框钢孔型设计中各斜轧孔型宽度相等为例，从金属不均匀变形出发，根据体积不变定律推导出计算变形过程中腰部与各腿部之间金属体积的转移公式。

7. Lead Spacing, Offset, Tweeze, Spread, Lead Extension, Skew, Gap, Width and Sweep, Missing, Broken, Twisted or Un-plated Leads.

引线间隔，偏移量，Tweeze，伸展，引线延长，歪斜，裂口，宽度，扫描，缺少的，断掉的，扭曲，未电镀引线

8. Based on the study of construction of a curved skew bridge, it is found out that the skew angle of bridge, rate of super-elevation, curve radius of road and bridge width etc are the causes of deviation of bridge axis.

通过对某斜弯桥的施工研究，找出桥梁斜交角度、超高率、道路曲线半径及桥梁宽度等是桥轴线发生偏位的原因，并推导出偏差的计算公式。