IPX网络配置与测试-CSDN博客

试验拓扑来源：BAIDU

简单的IPX配置：

Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#ipx routing
R1(config)#int e1/0
R1(config-if)#ipx network 12
R1(config-if)#no shu

Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#ipx routing
R2(config)#int e1/0
R2(config-if)#ipx network 12
R2(config-if)#no shu

使用show ipx int e1/0查看信息：

R1(config)#do show ipx int e1/0
Ethernet1/0 is up, line protocol is up
IPX address is 12.ca00.09ec.001c, NOVELL-ETHER [up]
Delay of this IPX network, in ticks is 1
IPXWAN processing not enabled on this interface.
IPX SAP update interval is 60 seconds
IPX type 20 propagation packet forwarding is disabled
Incoming access list is not set
Outgoing access list is not set
IPX helper access list is not set
SAP GGS output filter list is not set
SAP GNS processing enabled, delay 0 ms, output filter list is not set
SAP Input filter list is not set
SAP Output filter list is not set
SAP Router filter list is not set
Input filter list is not set
Output filter list is not set
Router filter list is not set
Netbios Input host access list is not set
Netbios Input bytes access list is not set
Netbios Output host access list is not set
Netbios Output bytes access list is not set
Updates each 60 seconds aging multiples RIP: 3 SAP: 3
SAP interpacket delay is 55 ms, maximum size is 480 bytes
RIP interpacket delay is 55 ms, maximum size is 432 bytes
RIP response delay is not set
IPX accounting is disabled
IPX fast switching is configured (enabled)
RIP packets received 1, RIP packets sent 1, 0 Throttled
RIP specific requests received 0, RIP specific replies sent 0
RIP general requests received 1, 0 ignored, RIP general replies sent 0
SAP packets received 1, SAP packets sent 1, 0 Throttled
SAP GNS packets received 0, SAP GNS replies sent 0
SAP GGS packets received 1, 0 ignored, SAP GGS replies sent 0
Router(config)#do ping 12.ca00.09ec.001c
Translating "12.ca00.09ec.001c"...domain server (255.255.255.255)

R2#show ipx int e1/0
Ethernet1/0 is up, line protocol is up
IPX address is 12.ca00.0e50.001c, NOVELL-ETHER [up]
Delay of this IPX network, in ticks is 1
IPXWAN processing not enabled on this interface.
IPX SAP update interval is 60 seconds
IPX type 20 propagation packet forwarding is disabled
Incoming access list is not set
Outgoing access list is not set
IPX helper access list is not set
SAP GGS output filter list is not set
SAP GNS processing enabled, delay 0 ms, output filter list is not set
SAP Input filter list is not set
SAP Output filter list is not set
SAP Router filter list is not set
Input filter list is not set
Output filter list is not set
Router filter list is not set
Netbios Input host access list is not set
Netbios Input bytes access list is not set
Netbios Output host access list is not set
Netbios Output bytes access list is not set
Updates each 60 seconds aging multiples RIP: 3 SAP: 3
SAP interpacket delay is 55 ms, maximum size is 480 bytes
RIP interpacket delay is 55 ms, maximum size is 432 bytes
RIP response delay is not set
IPX accounting is disabled
IPX fast switching is configured (enabled)
RIP packets received 0, RIP packets sent 1, 0 Throttled
RIP specific requests received 0, RIP specific replies sent 0
RIP general requests received 0, 0 ignored, RIP general replies sent 0
SAP packets received 0, SAP packets sent 1, 0 Throttled
SAP GNS packets received 0, SAP GNS replies sent 0
SAP GGS packets received 0, 0 ignored, SAP GGS replies sent 0

验证：

R1#ping 12.ca00.09ec.001c
Translating "12.ca00.09ec.001c"...domain server (255.255.255.255)

Type escape sequence to abort.
Sending 5, 100-byte IPX Novell Echoes to 12.ca00.09ec.001c, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

OK，很简单的实验，完。