imx6q linux dhcp,IMX6q 同时输出LVDS信号和HDMI信号,实现双屏同显功能

[    0.000000] Booting Linux on physical CPU 0x0

[    0.000000] Linux version 3.14.52-1.1.1_ga-svn0 (lijinliang@ubtby-13) (gcc version 4.9.2 (GCC) ) #668 SMP PREEMPT Sat Jan 26 16:26:19 CST 2019

[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d

[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine model: Freescale i.MX6 Quad SABRE Smart Device Board

[    0.000000] cma: CMA: reserved 320 MiB at 3c000000

[    0.000000] Memory policy: Data cache writealloc

[    0.000000] On node 0 totalpages: 262144

[    0.000000] free_area_init_node: node 0, pgdat 80cc8cc0, node_mem_map ab757000

[    0.000000]   DMA zone: 2048 pages used for memmap

[    0.000000]   DMA zone: 0 pages reserved

[    0.000000]   DMA zone: 262144 pages, LIFO batch:31

[    0.000000] PERCPU: Embedded 8 pages/cpu @ab732000 s8320 r8192 d16256 u32768

[    0.000000] pcpu-alloc: s8320 r8192 d16256 u32768 alloc=8*4096

[    0.000000] pcpu-alloc: [0] 0 [0] 1

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096

[    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk3p2 rootwait rw video=mxcfb0:dev=ldb,1920x1080@60,if=RGB24,bpp=32 video=mxcfb1:dev=hdmi,1920x1080M@60,if=RGB24,bpp=32 video=mxcfb2:off

[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Memory: 697540K/1048576K available (7738K kernel code, 432K rwdata, 2560K rodata, 2328K init, 438K bss, 351036K reserved, 0K highmem)

[    0.000000] Virtual kernel memory layout:

vector  : 0xffff0000 - 0xffff1000   (   4 kB)

fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

vmalloc : 0xc0800000 - 0xff000000   (1000 MB)

lowmem  : 0x80000000 - 0xc0000000   (1024 MB)

pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)

modules : 0x7f000000 - 0x7fe00000   (  14 MB)

.text : 0x80008000 - 0x80a16d14   (10300 kB)

.init : 0x80a17000 - 0x80c5d080   (2329 kB)

.data : 0x80c5e000 - 0x80cca1e0   ( 433 kB)

.bss : 0x80cca1ec - 0x80d37adc   ( 439 kB)

[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

[    0.000000] Preemptible hierarchical RCU implementation.

[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000000] L310 cache controller enabled

[    0.000000] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1024 kB

[    0.000000] Switching to timer-based delay loop

[    0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns

[    0.001055] Console: colour dummy device 80x30

[    0.001072] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)

[    0.001085] pid_max: default: 32768 minimum: 301

[    0.001246] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.001256] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

[    0.001931] CPU: Testing write buffer coherency: ok

[    0.002160] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[    0.002225] Setting up static identity map for 0x1075db30 - 0x1075db88

[    0.061263] CPU1: Booted secondary processor

[    0.061283] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[    0.061384] Brought up 2 CPUs

[    0.061395] SMP: Total of 2 processors activated (12.00 BogoMIPS).

[    0.061402] CPU: All CPU(s) started in SVC mode.

[    0.061923] devtmpfs: initialized

[    0.065700] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[    0.066001] pinctrl core: initialized pinctrl subsystem

[    0.066345] regulator-dummy: no parameters

[    0.082830] NET: Registered protocol family 16

[    0.091345] DMA: preallocated 256 KiB pool for atomic coherent allocations

[    0.091968] cpuidle: using governor ladder

[    0.091974] cpuidle: using governor menu

[    0.092238] CPU identified as i.MX6Q, silicon rev 1.5

[    0.092337] Use WDOG2 as reset source

[    0.101613] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered

[    0.101910] vdd1p1: 800 1375 mV at 1100 mV

[    0.102263] vdd3p0: 2625 3400 mV at 3000 mV

[    0.102618] vdd2p5: 2000 2750 mV at 2400 mV

[    0.102947] vddarm: 725 1450 mV at 1150 mV

[    0.110559] vddpu: 725 1450 mV

[    0.110919] vddsoc: 725 1450 mV at 1175 mV

[    0.113001] syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered

[    0.116200] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered

[    0.121187] 8250:Get irq number for GPIO 161, irq 321!

[    0.121197] 8250:Get irq number for GPIO 162, irq 322!

[    0.121205] 8250:Get irq number for GPIO 163, irq 323!

[    0.121211] 8250:Get irq number for GPIO 164, irq 324!

[    0.121548] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[    0.121557] hw-breakpoint: maximum watchpoint size is 4 bytes.

[    0.122269] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver

[    0.141514] bio: create slab at 0

[    0.143720] mxs-dma 110000.dma-apbh: initialized

[    0.144485] usb_otg_vbus: 5000 mV

[    0.144712] usb_h1_vbus: 5000 mV

[    0.144950] wm8962-supply: no parameters

[    0.145168] mipi_dsi_pwr_on: no parameters

[    0.145423] sensor-supply: 3300 mV

[    0.146159] vgaarb: loaded

[    0.146367] i2c-core: driver [max17135] using legacy suspend method

[    0.146373] i2c-core: driver [max17135] using legacy resume method

[    0.146998] SCSI subsystem initialized

[    0.147187] libata version 3.00 loaded.

[    0.147447] usbcore: registered new interface driver usbfs

[    0.147523] usbcore: registered new interface driver hub

[    0.147629] usbcore: registered new device driver usb

[    0.147772] usbphy_nop1.12 supply vcc not found, using dummy regulator

[    0.147870] usbphy_nop2.13 supply vcc not found, using dummy regulator

[    0.150056] i2c i2c-0: IMX I2C adapter registered

[    0.151665] i2c i2c-1: IMX I2C adapter registered

[    0.152580] i2c i2c-2: IMX I2C adapter registered

[    0.152716] Linux video capture interface: v2.00

[    0.152779] pps_core: LinuxPPS API ver. 1 registered

[    0.152785] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti

[    0.152806] PTP clock support registered

[    0.170679] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

[    0.190615] imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

[    0.191826] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed

[    0.191837] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a

[    0.191914] MIPI CSI2 driver module loaded

[    0.192148] Advanced Linux Sound Architecture Driver Initialized.

[    0.193211] Bluetooth: Core ver 2.18

[    0.193249] NET: Registered protocol family 31

[    0.193255] Bluetooth: HCI device and connection manager initialized

[    0.193271] Bluetooth: HCI socket layer initialized

[    0.193282] Bluetooth: L2CAP socket layer initialized

[    0.193313] Bluetooth: SCO socket layer initialized

[    0.193651] cfg80211: Calling CRDA to update world regulatory domain

[    0.194146] Switched to clocksource mxc_timer1

[    0.204109] NET: Registered protocol family 2

[    0.204901] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

[    0.204983] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

[    0.205116] TCP: Hash tables configured (established 8192 bind 8192)

[    0.205250] TCP: reno registered

[    0.205262] UDP hash table entries: 512 (order: 2, 16384 bytes)

[    0.205299] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

[    0.205547] NET: Registered protocol family 1

[    0.205881] RPC: Registered named UNIX socket transport module.

[    0.205888] RPC: Registered udp transport module.

[    0.205893] RPC: Registered tcp transport module.

[    0.205898] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.205909] PCI: CLS 0 bytes, default 64

[    0.206474] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

[    0.207320] imx_busfreq busfreq.16: DDR medium rate not supported.

[    0.207720] Bus freq driver module loaded

[    0.208491] futex hash table entries: 512 (order: 3, 32768 bytes)

[    0.215338] VFS: Disk quotas dquot_6.5.2

[    0.215591] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.217835] NFS: Registering the id_resolver key type

[    0.217868] Key type id_resolver registered

[    0.217875] Key type id_legacy registered

[    0.217910] jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.

[    0.218611] fuse init (API version 7.22)

[    0.219048] msgmni has been set to 2002

[    0.222073] io scheduler noop registered

[    0.222081] io scheduler deadline registered

[    0.222250] io scheduler cfq registered (default)

[    0.223371] imx-weim 28000000.imx-weim: can't request region for resource [mem 0x28000000-0x2bffffff]

[    0.223388] imx-weim: probe of 28000000.imx-weim failed with error -16

[    0.223650] imx-weim 2a000000.imx-weim: can't request region for resource [mem 0x2a000000-0x2dffffff]

[    0.223665] imx-weim: probe of 2a000000.imx-weim failed with error -16

[    0.223680] imx-weim 21b8000.weim: Driver registered.

[    0.223868] imx-weim 28000000.imx-weim: can't request region for resource [mem 0x28000000-0x2bffffff]

[    0.223883] imx-weim: probe of 28000000.imx-weim failed with error -16

[    0.223926] imx-weim 2a000000.imx-weim: can't request region for resource [mem 0x2a000000-0x2dffffff]

[    0.223940] imx-weim: probe of 2a000000.imx-weim failed with error -16

[    0.225970] ldb ldb.15: ldb_probe start !! !!!!!!!!!!

[    0.225991] ldb ldb.15: !!!!!split mode!!!

[    0.226051] ldb ldb.15: ldb->bus_mux_num = 2

[    0.226157] ldb ldb.15: ldb->bus_mux_num = 2

[    0.226167] ldb ldb.15: split mode or dual mode, ignoring second output

[    0.226842] mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed

[    0.226945] MIPI DSI driver module loaded

[    0.227153] MIPI DSI driver module loaded

[    0.228184] mxc_sdc_fb fb.24: registered mxc display driver ldb

[    0.274239] imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)

[    0.359596] Console: switching to colour frame buffer device 240x67

[    0.359601] do_bind_con_driver  *************my print j = 0 k = 0  vc->vc_cols = 240 vc->vc_rows = 67

[    0.411469] mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1

[    0.411492] fbcvt: 1920x1080@60: CVT Name - 2.073M9

[    0.411572] mxc_sdc_fb fb.25: registered mxc display driver hdmi

[    0.456505] uvesafb: failed to execute /sbin/v86d

[    0.456512] uvesafb: make sure that the v86d helper is installed and executable

[    0.456520] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)

[    0.456526] uvesafb: vbe_init() failed with -22

[    0.456540] uvesafb: probe of uvesafb.0 failed with error -22

[    0.457559] imx-sdma 20ec000.sdma: no iram assigned, using external mem

[    0.458483] imx-sdma 20ec000.sdma: no event needs to be remapped

[    0.459139] imx-sdma 20ec000.sdma: loaded firmware 3.2

[    0.461940] imx-sdma 20ec000.sdma: initialized

[    0.463549] pfuze100-regulator 1-0008: Full layer: 2, Metal layer: 1

[    0.464137] pfuze100-regulator 1-0008: FAB: 0, FIN: 0

[    0.464175] pfuze100-regulator 1-0008: pfuze100 found.

[    0.480622] SW1AB: 300 1875 mV at 1375 mV

[    0.481953] SW1C: 300 1875 mV at 1375 mV

[    0.483709] SW2: 800 3300 mV at 3300 mV

[    0.484464] SW3A: 400 1975 mV at 1500 mV

[    0.485210] SW3B: 400 1975 mV at 1500 mV

[    0.485976] SW4: 800 3300 mV at 3150 mV

[    0.486737] SWBST: 5000 5150 mV at 5000 mV

[    0.487481] VSNVS: 1000 3000 mV at 3000 mV

[    0.487651] VREFDDR: 750 mV

[    0.488378] VGEN1: 800 1550 mV at 1500 mV

[    0.489112] VGEN2: 800 1550 mV at 1500 mV

[    0.489871] VGEN3: 1800 3300 mV at 2800 mV

[    0.490605] VGEN4: 1800 3300 mV at 1800 mV

[    0.491341] VGEN5: 1800 3300 mV at 3000 mV

[    0.492083] VGEN6: 1800 3300 mV at 3300 mV

[    0.492419] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

[    0.493730] serial8250_register_8250_port  uart->port.uartclk = 7372800

[    0.513986] serial8250.6: ttySEX0 at MMIO 0x8000080 (irq = 321, base_baud = 460800) is a 16550A

[    0.514408] serial8250_register_8250_port  uart->port.uartclk = 7372800

[    0.534625] serial8250.6: ttySEX1 at MMIO 0x8000000 (irq = 322, base_baud = 460800) is a 16550A

[    0.535013] serial8250_register_8250_port  uart->port.uartclk = 7372800

[    0.555236] serial8250.6: ttySEX2 at MMIO 0xc000080 (irq = 323, base_baud = 460800) is a 16550A

[    0.555636] serial8250_register_8250_port  uart->port.uartclk = 7372800

[    0.575852] serial8250.6: ttySEX3 at MMIO 0xc000000 (irq = 324, base_baud = 460800) is a 16550A

[    0.576130] Serial: IMX driver

[    0.576459] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58, base_baud = 5000000) is a IMX

[    1.459859] console [ttymxc0] enabled

[    1.462855] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX

[    1.470605] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60, base_baud = 5000000) is a IMX

[    1.478352] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 61, base_baud = 5000000) is a IMX

[    1.486088] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 62, base_baud = 5000000) is a IMX

[    1.493719] serial: Freescale lpuart driver

[    1.497905] [drm] Initialized drm 1.1.0 20060810

[    1.501664] [drm] Initialized vivante 1.0.0 20120216 on minor 0

[    1.513704] brd: module loaded

[    1.519367] loop: module loaded

[    1.526920] spi_imx 2010000.ecspi: probed

[    1.531553] spi_imx 2018000.ecspi: probed

[    1.534774] spiPrinter register_chrdev  status = 247

[    1.539048] CAN device driver interface

[    1.543333] 2188000.ethernet supply phy not found, using dummy regulator

[    1.564546] pps pps0: new PPS source ptp0

[    1.568692] fec 2188000.ethernet (unregistered net_device): Invalid MAC address: 00:00:00:00:00:00

[    1.576392] fec 2188000.ethernet (unregistered net_device): Using random MAC address: 22:ef:27:71:c5:f0

[    1.588175] libphy: fec_enet_mii_bus: probed

[    1.591701] fec 2188000.ethernet eth0: registered PHC device 0

[    1.597037] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    1.602270] ehci-pci: EHCI PCI platform driver

[    1.605532] ehci-mxc: Freescale On-Chip EHCI Host driver

[    1.609716] usbcore: registered new interface driver usblp

[    1.613976] usbcore: registered new interface driver usb-storage

[    1.618780] usbcore: registered new interface driver usb_ehset_test

[    1.624810] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator

[    1.639325] ci_hdrc ci_hdrc.1: doesn't support gadget

[    1.643097] ci_hdrc ci_hdrc.1: EHCI Host Controller

[    1.646725] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1

[    1.664179] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00

[    1.669059] hub 1-0:1.0: USB hub found

[    1.671550] hub 1-0:1.0: 1 port detected

[    1.675083] mousedev: PS/2 mouse device common for all mice

[    1.679798] i2c-core: driver [isl29023] using legacy suspend method

[    1.684792] i2c-core: driver [isl29023] using legacy resume method

[    1.689830] #####################    isl1208_probe start ################

[    1.994186] usb 1-1: new full-speed USB device number 2 using ci_hdrc

[    2.148577] hub 1-1:1.0: USB hub found

[    2.151425] hub 1-1:1.0: 4 ports detected

[    2.204201] i2c /dev entries driver

[    2.206971] IR NEC protocol handler initialized

[    2.210207] IR RC5(x) protocol handler initialized

[    2.213701] IR RC6 protocol handler initialized

[    2.216951] IR JVC protocol handler initialized

[    2.220185] IR Sony protocol handler initialized

[    2.223505] IR RC5 (streamzap) protocol handler initialized

[    2.227792] IR SANYO protocol handler initialized

[    2.231200] IR MCE Keyboard/mouse protocol handler initialized

[    2.236769] mxc_v4l2_output v4l2_out.28: V4L2 device registered as video16

[    2.242483] mxc_v4l2_output v4l2_out.28: V4L2 device registered as video17

[    2.248218] mxc_v4l2_output v4l2_out.28: V4L2 device registered as video18

[    2.253947] mxc_v4l2_output v4l2_out.28: V4L2 device registered as video19

[    2.260056] i2c-core: driver [mag3110] using legacy suspend method

[    2.265012] i2c-core: driver [mag3110] using legacy resume method

[    2.774160] mma8451 0-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a!

[    2.779822] mma8451: probe of 0-001c failed with error -22

[    2.784435] imx2-wdt 20c0000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)

[    2.791495] Bluetooth: HCI UART driver ver 2.2

[    2.794686] Bluetooth: HCI H4 protocol initialized

[    2.798182] Bluetooth: HCI BCSP protocol initialized

[    2.801849] Bluetooth: HCIATH3K protocol initialized

[    2.805612] usbcore: registered new interface driver bcm203x

[    2.810049] usbcore: registered new interface driver btusb

[    2.814322] usbcore: registered new interface driver ath3k

[    2.818858] sdhci: Secure Digital Host Controller Interface driver

[    2.823743] sdhci: Copyright(c) Pierre Ossman

[    2.826822] sdhci-pltfm: SDHCI platform and OF driver helper

[    2.831880] imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_SD3_DAT4 already requested by 21e8000.serial; cannot claim for 2198000.usdhc

[    2.842431] imx6q-pinctrl 20e0000.iomuxc: pin-173 (2198000.usdhc) status -22

[    2.848202] imx6q-pinctrl 20e0000.iomuxc: could not request pin 173 (MX6Q_PAD_SD3_DAT4) from group usdhc3grp  on device 20e0000.iomuxc

[    2.859005] sdhci-esdhc-imx 2198000.usdhc: Error applying setting, reverse things back

[    2.867786] mmc2: no vqmmc regulator found

[    2.870595] mmc2: no vmmc regulator found

[    2.874581] imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_SD3_DAT4 already requested by 21e8000.serial; cannot claim for 2198000.usdhc

[    2.885114] imx6q-pinctrl 20e0000.iomuxc: pin-173 (2198000.usdhc) status -22

[    2.890870] imx6q-pinctrl 20e0000.iomuxc: could not request pin 173 (MX6Q_PAD_SD3_DAT4) from group usdhc3grp  on device 20e0000.iomuxc

[    2.901658] sdhci-esdhc-imx 2198000.usdhc: Error applying setting, reverse things back

[    2.925181] imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_SD3_DAT4 already requested by 21e8000.serial; cannot claim for 2198000.usdhc

[    2.935713] imx6q-pinctrl 20e0000.iomuxc: pin-173 (2198000.usdhc) status -22

[    2.941469] imx6q-pinctrl 20e0000.iomuxc: could not request pin 173 (MX6Q_PAD_SD3_DAT4) from group usdhc3grp  on device 20e0000.iomuxc

[    2.952258] sdhci-esdhc-imx 2198000.usdhc: Error applying setting, reverse things back

[    2.974176] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA

[    2.981138] imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_SD3_DAT4 already requested by 21e8000.serial; cannot claim for 2198000.usdhc

[    2.991669] imx6q-pinctrl 20e0000.iomuxc: pin-173 (2198000.usdhc) status -22

[    2.997425] imx6q-pinctrl 20e0000.iomuxc: could not request pin 173 (MX6Q_PAD_SD3_DAT4) from group usdhc3grp  on device 20e0000.iomuxc

[    3.008213] sdhci-esdhc-imx 2198000.usdhc: Error applying setting, reverse things back

[    3.015848] mmc3: no vqmmc regulator found

[    3.018658] mmc3: no vmmc regulator found

[    3.064196] mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA

[    3.070848] Warning: No contiguous memory is reserverd for gpu.!

[    3.078899] Warning: Will use default value(134217728) for the reserved memory!

[    3.085216] Galcore version 5.0.11.41671

[    3.094208] PU: Power-on latency exceeded, new value 4027000 ns

[    3.159789] mmc3: BKOPS_EN bit is not set

[    3.177014] mmc3: new high speed DDR MMC card at address 0001

[    3.182615] mmcblk3: mmc3:0001 Q2J55L 7.12 GiB

[    3.186617] mmcblk3boot0: mmc3:0001 Q2J55L partition 1 2.00 MiB

[    3.191876] mmcblk3boot1: mmc3:0001 Q2J55L partition 2 2.00 MiB

[    3.197193] mmcblk3rpmb: mmc3:0001 Q2J55L partition 3 4.00 MiB

[    3.203945]  mmcblk3: p1 p2

[    3.210022]  mmcblk3boot1: unknown partition table

[    3.217450]  mmcblk3boot0: unknown partition table

[    3.609746] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed

[    3.616822] mxc_vpu 2040000.vpu: VPU initialized

[    3.861778] caam 2100000.caam: Instantiated RNG4 SH0

[    4.103337] caam 2100000.caam: Instantiated RNG4 SH1

[    4.107026] caam 2100000.caam: device ID = 0x0a160100 (Era 4)

[    4.111479] caam 2100000.caam: job rings = 2, qi = 0

[    4.177353] caam algorithms registered in /proc/crypto

[    4.184896] caam_jr 2101000.jr0: registering rng-caam

[    4.189407] platform caam_sm: blkkey_ex: 4 keystore units available

[    4.195243] snvs-secvio 20cc000.caam-snvs: can't get snvs clock

[    4.199893] snvs-secvio 20cc000.caam-snvs: violation handlers armed - non-secure state

[    4.206886] usbcore: registered new interface driver usbhid

[    4.211164] usbhid: USB HID core driver

[    4.215642] 0-0018 supply IOVDD not found, using dummy regulator

[    4.220402] 0-0018 supply DVDD not found, using dummy regulator

[    4.225085] 0-0018 supply AVDD not found, using dummy regulator

[    4.229745] 0-0018 supply DRVDD not found, using dummy regulator

[    4.235297] fsl-asrc 2034000.asrc: driver registered

[    4.244459] tlv320aic3x-codec 0-0018: codec clk_frequency = 24000000

[    4.250374] tlv320aic3x-codec 0-0018: ASoC: no source widget found for Mic Bias 2V

[    4.256685] tlv320aic3x-codec 0-0018: ASoC: Failed to add route Mic Bias 2V -> direct -> MIC3L

[    4.264007] tlv320aic3x-codec 0-0018: ASoC: no source widget found for Mic Bias 2V

[    4.270299] tlv320aic3x-codec 0-0018: ASoC: Failed to add route Mic Bias 2V -> direct -> MIC3R

[    4.277634] tlv320aic3x-codec 0-0018: ASoC: no sink widget found for Mic Bias 2V

[    4.283735] tlv320aic3x-codec 0-0018: ASoC: Failed to add route Mic Jack -> direct -> Mic Bias 2V

[    4.293690] imx-tlv320 sound.22: tlv320aic3x-hifi 202c000.ssi mapping ok

[    4.307009] imx-audio-hdmi sound-hdmi.23: hdmi-hifi hdmi_audio.3 mapping ok

[    4.314800] NET: Registered protocol family 26

[    4.318083] TCP: cubic registered

[    4.320631] NET: Registered protocol family 10

[    4.324753] sit: IPv6 over IPv4 tunneling driver

[    4.328738] NET: Registered protocol family 17

[    4.331902] can: controller area network core (rev 20120528 abi 9)

[    4.336885] NET: Registered protocol family 29

[    4.340036] can: raw protocol (rev 20120528)

[    4.343010] can: broadcast manager protocol (rev 20120528 t)

[    4.347396] can: netlink gateway (rev 20130117) max_hops=1

[    4.351864] Bluetooth: RFCOMM TTY layer initialized

[    4.355481] Bluetooth: RFCOMM socket layer initialized

[    4.359340] Bluetooth: RFCOMM ver 1.11

[    4.361800] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

[    4.365830] Bluetooth: BNEP filters: protocol multicast

[    4.369768] Bluetooth: BNEP socket layer initialized

[    4.373437] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

[    4.378078] Bluetooth: HIDP socket layer initialized

[    4.381785] 8021q: 802.1Q VLAN Support v1.8

[    4.384729] Key type dns_resolver registered

[    4.722741] imx6q-pcie 1ffc000.pcie: phy link never came up

[    4.727040] imx6q-pcie 1ffc000.pcie: Failed to bring link up!

[    4.731506] imx6q-pcie 1ffc000.pcie: failed to initialize host

[    4.736097] imx6q-pcie: probe of 1ffc000.pcie failed with error -22

[    4.741935] VGEN3: disabling

[    4.744000] VGEN2: disabling

[    4.746074] VGEN1: disabling

[    4.748122] SWBST: disabling

[    4.749707] SW4: disabling

[    4.751122] wm8962-supply: disabling

[    4.753400] usb_otg_vbus: disabling

[    4.755613] regulator-dummy: disabling

[    4.758657] Atmel-308U:[6758]mxt_init.

[    4.761215] Atmel-308U:[6409]step 1: parse dts.

[    4.764582] atmel_mxt_ts 2-004a: Unable to read gpio mask

[    4.768700] atmel_mxt_ts 2-004a: Unable to read vendor id

[    4.772806] atmel_mxt_ts 2-004a: Unable to read panel id

[    4.776864] atmel_mxt_ts 2-004a: Unable to read vendor id

[    4.780971] atmel_mxt_ts 2-004a: Unable to read panel id

[    4.785021] atmel_mxt_ts 2-004a: ATMEL DEVICE TREE:

[    4.788604] atmel_mxt_ts 2-004a: reset gpio= 9

[    4.791753] atmel_mxt_ts 2-004a: irq gpio= 8

[    4.794740] atmel_mxt_ts 2-004a: fw name = mXT336U10AA.fw

[    4.798844] atmel_mxt_ts 2-004a: config size = 2

[    4.802166] atmel_mxt_ts 2-004a: gpio mask = 0x0

[    4.805500] atmel_mxt_ts 2-004a: default config = 0

[    4.809083] atmel_mxt_ts 2-004a: default panel id = 0

[    4.812839] atmel_mxt_ts 2-004a: use ptc key = 0

[    4.816172] atmel_mxt_ts 2-004a: cut off power = 0

[    4.819668] atmel_mxt_ts 2-004a: config[0]: family_id = 0xa6

[    4.824033] atmel_mxt_ts 2-004a: config[0]: variant_id = 0x6

[    4.828408] atmel_mxt_ts 2-004a: config[0]: version = 0x10

[    4.832599] atmel_mxt_ts 2-004a: config[0]: build = 0xaa

[    4.836627] atmel_mxt_ts 2-004a: config[0]: mxt_cfg_name = mxt_336u_biel_hw1_config.fw

[    4.843250] atmel_mxt_ts 2-004a: config[0]: vendor_id = 0x0

[    4.847548] atmel_mxt_ts 2-004a: config[0]: panel_id = 0x0

[    4.851739] atmel_mxt_ts 2-004a: config[0]: rev_id = 0x2

[    4.855768] atmel_mxt_ts 2-004a: config[0]: wakeup self adcx = 0x10

[    4.860741] atmel_mxt_ts 2-004a: config[1]: family_id = 0xa6

[    4.865117] atmel_mxt_ts 2-004a: config[1]: variant_id = 0x6

[    4.869481] atmel_mxt_ts 2-004a: config[1]: version = 0x10

[    4.873671] atmel_mxt_ts 2-004a: config[1]: build = 0xaa

[    4.877700] atmel_mxt_ts 2-004a: config[1]: mxt_cfg_name = mxt_336u_biel_hw2_config.fw

[    4.884333] atmel_mxt_ts 2-004a: config[1]: vendor_id = 0x0

[    4.888611] atmel_mxt_ts 2-004a: config[1]: panel_id = 0x0

[    4.892801] atmel_mxt_ts 2-004a: config[1]: rev_id = 0x2

[    4.896828] atmel_mxt_ts 2-004a: config[1]: wakeup self adcx = 0x10

[    4.901800] atmel_mxt_ts 2-004a: END OF ATMEL DEVICE TREE

[    4.905913] Atmel-308U:[6440]step 2: Power on .

[    4.909234] Atmel-308U:[6463]step 3 : reset IC.

[    5.142485] atmel_mxt_ts 2-004a: mxt_wait_for_chg() timeout!

[    5.146861] Atmel-308U:[6516]step 4 : test IC I2C.

[    5.150520] atmel_mxt_ts 2-004a: mxt_read_reg: i2c transfer failed (-5)

[    5.155857] atmel_mxt_ts 2-004a: Bootloader i2c addr: 0x26

[    5.160203] atmel_mxt_ts 2-004a: mxt_probe_bootloader: i2c recv failed

[    5.165453] atmel_mxt_ts 2-004a: reset gpio = 0

[    5.168690] atmel_mxt_ts 2-004a: chg gpio = 1

[    5.171762] atmel_mxt_ts: probe of 2-004a failed with error -5

[    5.176352] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[    5.192733] ALSA device list:

[    5.194459]   #0: imx-tlv320

[    5.196045]   #1: imx-hdmi-soc

[    6.027180] kjournald starting.  Commit interval 5 seconds

[    6.028216] EXT3-fs (mmcblk3p2): using internal journal

[    6.029179] EXT3-fs (mmcblk3p2): recovery complete

[    6.029184] EXT3-fs (mmcblk3p2): mounted filesystem with ordered data mode

[    6.029220] VFS: Mounted root (ext3 filesystem) on device 179:2.

[    6.030624] devtmpfs: mounted

[    6.035642] Freeing unused kernel memory: 2328K (80a17000 - 80c5d000)

[    6.453517] udevd[190]: starting version 182

[    7.417954] random: dropbear urandom read with 118 bits of entropy available

[    7.894189] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)

[    7.944360] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[   12.082797] random: nonblocking pool is initialized

root@imx6qsabresd:/#

root@imx6qsabresd:/#