加载失败时的启动日志
System startup
Uncompress Ok!
U-Boot 2020.01 (Sep 01 2020 - 09:25:23 +0800)hi3516dv300
DRAM: MMC:
EMMC/MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:1
mix set temp-phase 3
scan elemnts: startp:3 endp:122
Tuning SampleClock. mix set phase:[03/07] ele:[14d/16]
MMC/SD Card:
MID: 0x15
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "8GTF4"
Chip Type: MMC
Version: 0.0
Speed: 100000000Hz
Bus Width: 4bit
himci: 0 (eMMC)
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: eth0
Error: eth0 address not set.
Hit any key to stop autoboot: 0
MMC read: dev # 0, block # 2048, count 18432 ... 18432 blocks read: OK
45.29 MB/s
## Starting application at 0x80000000 ...
******************Welcome******************
Processor : Cortex-A7 * 2
Run Mode : SMP
GIC Rev : GICv2
build time : Nov 6 2020 08:38:54
Kernel : Huawei LiteOS 2.0.0.35/debug
*******************************************
main core booting up...
releasing 1 secondary cores
cpu 0 entering scheduler
cpu 1 entering scheduler
random dev init ...
proc fs init ...
Mount procfs finished.
MMC dev init ...[ERR]No console dev used.
[ERR]No console dev used.
disk_init : register /dev/mmcblk0 ok!
mem dev init ...
spi nor flash init ...
spinor_get_dev_id(56): Spi(cs0) have no device.
Cs[0] have no device!!!
spinor_get_dev_id(56): Spi(cs1) have no device.
Cs[1] have no device!!!
hifmc100_attach(130): Error:spinor scan fail!
net init ...
tcpip_init start
tcpip_init end
Ethernet start.hisi_eth: User did not set phy mode, use default=rmii
hisi_eth: User did not set phy addr, auto scan...
No OTP data, festa PHY use default ATE parameters!
festa PHY wait autotrim done timeout!
Detected phy addr 1, phyid: 0x1cc816
spinor_get_dev_id(56): Spi(cs0) have no device.
Cs[0] have no device!!!
spinor_get_dev_id(56): Spi(cs1) have no device.
Cs[1] have no device!!!
hifmc100_attach(130): Error:spinor scan fail!
netif_is_link_up overtime!
************************************************************
usb init ...
******** usb_init in **********
usb v3.05 2019-11-20 10:40
xhci_init (xhci0): 64 bytes context size, 32-bit DMA
usb_bus_attach (usbus0): 5.0Gbps Super Speed USB v3.0
spinor_get_dev_id(56): Spi(cs0) have no device.
Cs[0] have no device!!!
spinor_get_dev_id(56): Spi(cs1) have no device.
Cs[1] have no device!!!
hifmc100_attach(130): Error:spinor scan fail!
******** usb_init ok**********
Date:Nov 6 2020.
Time:08:40:18.
ugen0.1: at usbus0
OsMountRootfs start ...
device_set_usb_desc (uhub0): on usbus0
disk_init : register /dev/mmcblk0 ok!
DiskAddPart : register /dev/mmcblk0p0 ok!
DiskAddPart : register /dev/mmcblk0p1 ok!
DiskAddPart : register /dev/mmcblk0p2 ok!
OsMountRootfs end ...
g_mmz_start=0x88000000, g_mmz_size=0x180
mmz param= anonymous,0,0x88000000,384M
<6>Hisilicon Media Memory Zone Manager
Load hifb.ko OK!
[VERSION]:Hi3881V100R001C00SPC020 2020-07-16 23:15:00
oam_main_init SUCCESSFULLY!
wal_customize_init SUCCESSFULLY!
oal_main_init SUCCESSFULLY
frw_main_init SUCCESSFULLY!
hi_wifi_plat_init SUCCESSFULLY
uhub_attach (uhub0): 1 port with 1 removable, self powered
[12022][E:184]sdio rescan failed.
[12022][E:2134]No SDIO card
[12022][E:1625]hcc_host_init:: sdio_probe failed!
[12026][E:2120]No SDIO card
[12029][E:583]hcc_host_init fail![1]
[12033][E:272]hi_wifi_host_init: hcc_hmac_init return error code: 1
[12039][E:151]wifi host initialize fail.
[ERR][HDF:E/HDF_LOG_TAG]HdfWifiChipInit:init chip hisi error ret=1
[ERR][HDF:E/HDF_LOG_TAG]HdfWifiDriverInit:init chip 0 error ret=-210, feature 65535 is unavailable!
[ERR][HDF:E/devhost_service_clnt]Install hdfwifi driver failed, ret = -204
sdk init end
cat log shell end
[Init] ****/****/****/****/OpenHarmony/****/****/3/OpenHarmony 1.0/debug
[Init] DoMount, failed