linux flash分区扩容,linux 2.6.20.3自定义nand flash分区表问题

, channels ----

13: , channels ----

14: usb-ep1, channels 0---

15: usb-ep2, channels -1--

16: usb-ep3, channels --2-

17: usb-ep4, channels ---3

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 2048 bind 1024)

TCP reno registered

NetWinder Floating Point Emulator V0.97 (double precision)

JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler deadline registered

io scheduler cfq registered

s3c2410-lcd s3c2410-lcd: no platform data for lcd, cannot attach

s3c2410-lcd: probe of s3c2410-lcd failed with error -22

lp: driver loaded but no devices found

ppdev: user-space parallel port driver

S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410

s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410

s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

loop: loaded (max 8 devices)

dm9000 Ethernet Driver

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx

BAST NOR-Flash Driver, (c) 2004 Simtec Electronics

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2410-nand s3c2410-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns

NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)

NAND_ECC_NONE selected by board driver. This is not recommended !!

Scanning device for bad blocks

Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":

0x00000000-0x00004000 : "Boot Agent"

0x00000000-0x00200000 : "S3C2410 flash partition 1"

0x00400000-0x00800000 : "S3C2410 flash partition 2"

0x00800000-0x00a00000 : "S3C2410 flash partition 3"

0x00a00000-0x00e00000 : "S3C2410 flash partition 4"

0x00e00000-0x01800000 : "S3C2410 flash partition 5"

0x01800000-0x03000000 : "S3C2410 flash partition 6"

0x03000000-0x04000000 : "S3C2410 flash partition 7"usbmon: debugfs is not available

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

mice: PS/2 mouse device common for all mice

S3C24XX RTC, (c) 2004,2006 Simtec Electronics

s3c2410-i2c s3c2410-i2c: slave address 0x10

s3c2410-i2c s3c2410-i2c: bus frequency set to 99 KHz

s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter

TCP cubic registered

NET: Registered protocol family 1

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

No filesystem could mount root, tried: ext3 cramfs msdos vfat romfs

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)