VCA821可变增益放大器

目录

原理图

PCB

规格书

---

废话不多说，直接上图：

原理图

PCB

 经过测试，是能够正常使用的。

规格书

The VCA821 device is a DC-coupled, wideband, linear in dB, continuously variable, voltage-controlled gain amplifier. It provides a differential input to singleended conversion with a high-impedance gain control input used to vary the gain down 40 dB from the nominal maximum gain set by the gain resistor (RG) and feedback resistor (RF). The VCA821 device internal architecture consists of two input buffers and an output current feedback amplifier stage integrated with a multiplier core to provide a complete variable gain amplifier (VGA) system that does not require external buffering. The maximum gain is set externally with two resistors, providing flexibility in designs. The maximum gain is intended to be set between 6 dB and 32 dB. Operating from ±5-V supplies, the gain control voltage for the VCA821 device adjusts the gain linearly in dB as the control voltage varies from 0V to +2 V. For example, set at a maximum gain of 20 dB, the VCA821 device provides 20 dB, at VG = +2 V, to less than –20 dB at VG = 0 V. The VCA821 device offers excellent gain linearity. For a 20-dB maximum gain, and a gain-control input voltage varying between +1 V and +2 V, the gain does not deviate by more than ±0.3 dB (maximum at +25°C).

VCA821器件是一种直流耦合、宽带、线性dB，连续可变，电压控制增益放大器。它为具有高阻抗增益控制的单线转换提供差分输入输入用于改变增益从40 dB增益电阻设定的标称最大增益(RG)和反馈电阻(RF)。VCA821设备内部架构包括两个输入缓冲器一个输出电流反馈放大级集成了一个乘法器核心提供一个完整的可变增益放大器(VGA)不需要外部缓冲的系统。的最大增益设置在外部的两个电阻，提供设计的灵活性。最大增益为设定在6分贝到32分贝之间。从±5v电源工作，增益控制VCA821器件的电压调节增益当控制电压从0V到+ 2 V。例如，将最大增益设置为20db，在VG = + 2v时，VCA821器件提供20db在VG = 0 V时小于-20 dB。VCA821设备提供优秀的增益线性。最大20db增益和增益控制输入电压变化在+ 1v和+ 2v之间，增益不会偏离大于±0.3 dB(+25℃时最大)。

 

 Overview The VCA821 is a voltage controlled variable gain amplifier with differential inputs and a single ended output. The maximum gain is set by external resistors while the gain range is controlled by an external analog voltage. The maximum gain is designed for gains of 2 V/V up to 100 V/V and the analog control allows a gain range of over 40 dB. The VCA821 Input consists of two buffers which, together create a fully symmetrical, high impedance differential input with a typical common mode rejection of 80 dB. The gain set resistor is connected between the two input buffer output pins, so that the input impedance is independent of the gain settings. The bipolar inputs have a input voltage range of +1.6 V and –2.1 V on ±5 V supplies. The amplifier maximum gain is set by external resistors, but the internal gain control circuit is controlled by a continuously variable, analog voltage. The gain control is a multiplier stage which is linear in dB. The gain control input pin operates over a voltage range of 0 V to 2 V. The VCA821 contains a high speed, high current output buffer. The output stage can typically swing ±3.9 V and source/sink ±90 mA. The VCA821 can be operated over a voltage range of ±3.5 V to ±6 V. 9.2 Feature Description The VCA821 can be operated with both single ended or differential input signals. The inputs present consistently high impedance across all gain configurations. By using an analog control signal the amplifier gain is continuously variable for smooth, glitch free gain changes. With a large signal bandwidth of 320 MHz and a slew rate of 2500 V/us the VCA821 offers linear performance over a wide range of signal amplitudes and gain settings. The low impedance/high current output buffer can drive loads ranging from low impedance transmission lines to high-impedance, switched-capacitor analog to digital converters. By using closely matched internal components the VCA821 offers gain accuracy of ±0.3 dB. 9.3 Device Functional Modes The VCA821 functions as a differential input, single-ended output variable gain amplifier. This functional mode is enabled by applying power to the amplifier supply pins and is disabled by turning the power off. The gain is continuously variable through the analog gain control input. While the gain range is fixed the maximum gain is set by two external components, Rf and Rg as shown in the Figure 73. The maximum gain is equal to 2x (Rf / Rg). This gain is achieved with a 2-V voltage on the gain adjust pin VG. As the voltage decreases on the VG pin, the gain decreases in a linear in dB fashion with over 40 dB of gain range from 2-V to 0-V control voltage. As with most other differential input amplifiers, inputs can be applied to either one or both of the amplifier inputs. The amplifier gain is controlled through the gain control pin.

概述
VCA821是一个压控可变增益放大器，具有差分输入和单端输出。这个
最大增益由外部电阻器设置，而增益范围由外部模拟电压控制。这个
最大增益设计为2 V/V至100 V/V的增益，模拟控制允许超过
40分贝。VCA821输入由两个缓冲器组成，它们共同形成完全对称的高阻抗
差分输入，典型共模抑制为80dB。增益设置电阻器连接在
两个输入缓冲器输出引脚，使得输入阻抗与增益设置无关。双极输入
在±5 V电源上，输入电压范围为+1.6 V和-2.1 V。放大器最大增益由外部设置
电阻器，但内部增益控制电路由连续可变的模拟电压控制。收益
控制是一个以dB为单位呈线性的乘法级。增益控制输入引脚在0 V的电压范围内工作
VCA821包含一个高速、大电流输出缓冲器。输出级通常可以摆动±3.9
V和源/汇±90 mA。VCA821可以在±3.5 V至±6 V的电压范围内工作。
9.2功能描述
VCA821可以用单端或差分输入信号操作。输入一致
跨所有增益配置的高阻抗。通过使用模拟控制信号，放大器增益为
连续可变，实现平滑、无毛刺的增益变化。具有320 MHz的大信号带宽和转换
VCA821的速率为2500V/us，在广泛的信号幅度和增益范围内提供线性性能
设置。低阻抗/高电流输出缓冲器可以驱动低阻抗传输的负载
线路连接到高阻抗开关电容器模数转换器。通过使用紧密匹配的内部
VCA821的增益精度为±0.3 dB。
9.3设备功能模式
VCA821用作差分输入、单端输出可变增益放大器。此功能模式为
通过向放大器电源引脚供电启用，并通过关闭电源禁用。
增益通过模拟增益控制输入连续可变。虽然增益范围是固定的
最大增益由两个外部组件Rf和Rg设置，如图73所示。最大增益为
等于2x（Rf/Rg）。该增益是通过增益调节引脚VG上的2-V电压实现的
VG引脚上的增益减小，增益以dB为单位呈线性减小，增益范围从2-V到
0-V控制电压。
与大多数其他差分输入放大器一样，输入可以施加到放大器输入中的一个或两个。
放大器增益通过增益控制引脚控制。