1、使用FETA40i-C V1.2(国产化版本)核心板+OKA40i-C V1.2底板 烧写镜像使用sun8iw11p1_linux_OKA40i_C_uart0-1024x600;2019年10月版本和2020年3月版本均试过
USB烧写,下载到69%后卡住,等待10秒后提示“烧写固件失败,请确保固件文件有效并且智能设备可以正常工作”;
SD卡烧写,使用TF卡用大卡套插入SD卡插槽,使用串口查看烧写打印信息,烧写一部分后报错停止;
整体log如下:
HELLO! BOOT0 is starting!
[ 0.35]HELLO! BOOT0 is starting!
[ 0.39]boot0 commit : b58d49ff80aa5ff8865ab68aa2463d4ee0fe1e7d
[ 0.46]boot0 version : 4.0
[ 0.50]set pll start
[ 0.54]set pll end
[ 0.89]rtc[0] value = 0x00000000
[ 0.92]rtc[1] value = 0x00000000
[ 0.95]rtc[2] value = 0x00000000
[ 0.98]rtc[3] value = 0x00000000
[ 0.102]rtc[4] value = 0x00000000
[ 0.105]rtc[5] value = 0x00000000
[ 0.109]DRAMC IS FOUR
[ 0.111]DRAM BOOT DRIVE INFO: V1.1
[ 0.115]Found A40
[ 0.117]Found A40
[ 0.119]Found A40
[ 0.121]Found A40
[ 0.123]Found A40
[ 0.129]PMU: [ 0.130]AXP221
[ 0.132]ddr voltage = 1250 mv
[ 0.139]PMU: [ 0.140]AXP221
[ 0.142]ddr voltage = 1250 mv
[ 0.153]PMU: [ 0.154]AXP221
[ 0.156]ddr voltage = 1500 mv
[ 0.166]DRAM CLK =576 MHZ
[ 0.169]DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[ 0.174]DRAM zq value: 0x003b3bfb
[ 0.180]DRAM SIZE =1024 M
[ 0.183]DRAM ** test OK.
[ 0.186]dram size =1024
[ 0.188]rtc standby flag is 0x00000000, super standby flag is 0x00000000
[ 0.196]card no is 0
[ 0.198]sdcard 0 line count 4
[ 0.201][mmc]: mmc driver ver 2016-07-01 15:30
[ 0.206][mmc]: sdc0 spd mode error, 2
[ 0.219][mmc]: Wrong media type 0x00000000
[ 0.223][mmc]: ***Try SD card 0***
[ 0.235][mmc]: HSSDR52/SDR25 4 bit
[ 0.238][mmc]: 50000000 Hz
[ 0.241][mmc]: 15364 MB
[ 0.243][mmc]: ***SD/MMC 0 init OK!!!***
[ 0.343]Succeed in loading uboot from sdmmc flash.
[ 0.348]Entry_name = u-boot
[ 0.364]Ready to disable icache.
[ 0.367]Jump to secend Boot.
U-Boot 2014.07 (Jan 19 2020 - 05:27:12) Allwinner Technology
uboot commit : ffae925c54abddcfc8f616c65bb6eb8a3076b947
i2c_init: by cpux
i2c_init ok
[ 0.382]pmbus: ready
[ 0.396]PMU: AXP221
[ 0.396]PMU: AXP22x found
[ 0.397]PMU: dcdc2 1160
[ 0.398]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz MBus=400Mhz
set power on vol to default
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1160, onoff=1
dcdc3_vol = 1200, onoff=1
dcdc4_vol = 1100, onoff=0
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dc1sw_vol = 3000, onoff=0
dc5ldo_vol = 1100, onoff=0
dldo1_vol = 3300, onoff=1
dldo2_vol = 3300, onoff=0
dldo3_vol = 3300, onoff=0
dldo4_vol = 2500, onoff=1
eldo1_vol = 2800, onoff=0
eldo2_vol = 1200, onoff=1
eldo3_vol = 2800, onoff=1
gpio0_vol = 3300, onoff=1
gpio1_vol = 3300, onoff=1
find power_sply to end
vbus exist
DRAM: 1 GiB
fdt addr: 0x76e8dcd8
Relocation Offset is: 35ee4000
In: serial
Out: serial
Err: serial
gic: normal mode
[ 0.527]start
drv_disp_init
init_clocks