华为ENsp 单臂路由

最新推荐文章于 2024-06-14 14:08:20 发布

编程老菜鸡

最新推荐文章于 2024-06-14 14:08:20 发布

阅读量296

点赞数 1

本文链接：https://blog.csdn.net/weixin_44868492/article/details/116201087

版权

关键词由CSDN通过智能技术生成

单臂路由配置

网络拓扑：
在这里插入图片描述
PC1：
ip:192.168.67.11 /24
gateway:192.168.67.1
PC2:
ip:192.168.66.11 /24
gateway:192.168.66.1

SW-1交换机配置：

[Huawei]sysname SW-1
[SW-1]vlan batch 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW-1]interface Ethernet0/0/1
[SW-1-Ethernet0/0/1]port link-type access
[SW-1-Ethernet0/0/1]port default vlan 10
[SW-1-Ethernet0/0/1]interface Ethernet0/0/2
[SW-1-Ethernet0/0/2]port link-type access
[SW-1-Ethernet0/0/2]port default vlan 20
[SW-1-Ethernet0/0/2]port default vlan 10
[SW-1-Ethernet0/0/2]interface Ethernet0/0/5
[SW-1-Ethernet0/0/5]port link-type access
[SW-1-Ethernet0/0/5]port default vlan 20
[SW-1-Ethernet0/0/5]interface Ethernet0/0/6
[SW-1-Ethernet0/0/6]port link-type access
[SW-1-Ethernet0/0/6]port default vlan 20
[SW-1-Ethernet0/0/6]quit
[SW-1]interface GigabitEthernet0/0/1
[SW-1-GigabitEthernet0/0/1]port link-type trunk
[SW-1-GigabitEthernet0/0/1]port trunk allow-pass vlan 10 20
[SW-1-GigabitEthernet0/0/1]quit
[SW-1]

R-1路由器配置
1）.将路由器和交换机直连的GE0/0/1接口划分为两个逻辑接口
interface GigabitEthernet0/0/1.1
interface GigabitEthernet0/0/1.2
然后分别为这两个逻辑接口配置PC1和PC2的网关地址

[R-1]interface GigabitEthernet0/0/1.1
[R-1-GigabitEthernet0/0/1.1]ip address 192.168.67.1 24
[R-1-GigabitEthernet0/0/1.1]dot	
[R-1-GigabitEthernet0/0/1.1]dot1q termi	
[R-1-GigabitEthernet0/0/1.1]dot1q termination vid 10
[R-1-GigabitEthernet0/0/1.1]arp broadcas	
[R-1-GigabitEthernet0/0/1.1]arp broadcast enable
[R-1-GigabitEthernet0/0/1.1]quit
[R-1]interface GigabitEthernet0/0/1.2
[R-1-GigabitEthernet0/0/1.2]ip address 192.168.66.1 24
[R-1-GigabitEthernet0/0/1.2]dot1	
[R-1-GigabitEthernet0/0/1.2]dot1q termination vid 20
[R-1-GigabitEthernet0/0/1.2]arp broadcast enable
[R-1-GigabitEthernet0/0/1.2]