拓扑图
OSPF命令:
-
dis ospf pee b ##查看邻居关系
dis ip routing-table pro ospf -
ospf 1 route 1.1.1.1 ####OSPF指定个route-id、1是表示,只在本区域有效
route id 1.1.1.1 ###全局模式下配置 这个router-id所有协议生效 -
reset ospf 1 process ###1是进程号 重启ospf
-
ospf 配置方法
ospf 1 route 1.1.1.1 ###配置route-id
ospf 10 ##启动ospf 它的进程号是10
area 0 ###进入区域0 骨干区域
network 20.0.0.0 0.0.0.3 ###宣告网段 20.0.0.0 反掩码 0.0.0.3 (32位) -
引入路由
ospf 1
import-route rip 1 type 1 cost 5 ###默认引入type 2 度量值是不累加的 这种是不科学的,一般引入type 1,要累加 cost 5 是花销 -
引路由
rip 1
import-route ospf 1 -
末梢区域
stub ###末梢 2变都要加
完全末梢在abr上 加入
stub no-summary
nssa区域 ###ASBR主要是靠5类的LSA来通告链路状态信息,可以用7类LSA优化,通告外部路由信息
配置命令
R1上配置命令如下:
interface GigabitEthernet 0/0/0
ip address 16.0.0.1 24
interface GigabitEthernet 0/0/1
ip address 12.0.0.1 24
interface LoopBack 0
ip address 1.1.1.1 32
ospf 1 router-id 1.1.1.1 #ospf 1路由器id为1.1.1.1
area 1 #区域1
network 12.0.0.0 0.0.0.255
network 1.1.1.1 0.0.0.0
rip 1 #宣告rip
version 2 #rip的版本
undo summary #关闭汇总
network 16.0.0.0
import-route ospf 1 #注入 ospf 1
ospf 1 #区域1
import-route rip 1 type 1 cost 5 #注入 rip1 路由器LSA 花费5
ospf 1 router-id 1.1.1.1
area 1
nssa #宣告 定义为nssa协议
R2上配置命令如下:
interface GigabitEthernet 0/0/1
ip address 12.0.0.2 24
interface GigabitEthernet 0/0/2
ip address 23.0.0.2 24
interface LoopBack 0
ip address 2.2.2.2 32
ospf 1 router-id 2.2.2.2 #ospf 1路由器id为2.2.2.2
area 1 #区域1
network 2.2.2.2 0.0.0.0
network 12.0.0.0 0.0.0.255
network 23.0.0.0 0.0.0.255
ospf 1 router-id 2.2.2.2
area 1
nssa #宣告 定义为nssa协议
R3上配置命令如下:
interface GigabitEthernet 0/0/2
ip address 23.0.0.3 24
interface GigabitEthernet 0/0/3
ip address 34.0.0.3 24
interface LoopBack 0
ip address 3.3.3.3 32
ospf 1 router-id 3.3.3.3 #ospf 1路由器id为3.3.3.3
area 1 #区域1
network 23.0.0.0 0.0.0.255
area 0 #区域0
network 3.3.3.3 0.0.0.0
network 34.0.0.0 0.0.0.255
ospf 1 router-id 3.3.3.3
area 1
nssa #宣告 定义为nssa协议
R4上配置命令如下:
interface GigabitEthernet 0/0/3
ip address 34.0.0.4 24
interface GigabitEthernet 0/0/0
ip address 45.0.0.4 24
interface LoopBack 0
ip address 4.4.4.4 32
ospf 1 router-id 4.4.4.4 #ospf 1路由器id为4.4.4.4
area 0 #区域0
network 34.0.0.0 0.0.0.255
network 4.4.4.4 0.0.0.0
area 2 #区域2
network 45.0.0.0 0.0.0.255
ospf 1 router-id 4.4.4.4
area 2
stub no-summary #完全末梢区域
R5上配置命令如下:
interface GigabitEthernet 0/0/0
ip address 45.0.0.5 24
interface LoopBack 0
ip address 5.5.5.5 32
ospf 1 router-id 5.5.5.5 #ospf 1路由器id为5.5.5.5
area 2 #区域2
network 45.0.0.0 0.0.0.255
network 5.5.5.5 0.0.0.0
ospf 1 router-id 5.5.5.5 #ospf 1路由器id为5.5.5.5
area 2 #区域2
stub
R6上配置命令如下:
interface GigabitEthernet 0/0/0
ip address 16.0.0.6 24
interface LoopBack 0
ip address 6.6.6.6 32
rip 1 #宣告rip
version 2 #rip的版本
undo summary #关闭汇总
network 16.0.0.0
network 6.0.0.0
rip 1
import-route ospf 1 cost 4 #注入 路由器LSA 花费4