HCIA综合实验

最新推荐文章于 2024-09-06 12:00:00 发布
最新推荐文章于 2024-09-06 12:00:00 发布
阅读量1.6k 收藏
点赞数
分类专栏： 作业 文章标签： 网络 服务器 运维
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/weixin_55769892/article/details/128499886
版权

实验要求：

1、AR6理解为ISP设备，所连接的两个网段为公网www.beixin.com来访问http服务器；R1-R5构建为一个私有的局域网；

2、AR6上只能进行ip地址配置，之后不得对该路由器进行其他任何配置

3、公网范围IP地址已经指定，剩余R1-R5整个私网使用192.168.1.0/24进行合理分配

4、PC1/3为划分到VLAN2，PC2/4/HTTP 服务器划分到VLAN3；PC1-4通过DHCP自动获取ip地址；

5、所有路由器路由表应尽量控制减少，预防出现环路，所有选路均为最佳路径；R4与R5之间正常使用1000M链路，

1000M链路故障时自动切换到100m链路，整个网络仅使用静态路由协议；

6、PC1—PC4均可ping通PC5，同时PC5可以通过域名www.beixin.com来访问http服务器；

7、全网仅R1可以telnet登录R2

lsw1

[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]port l a
[Huawei-Ethernet0/0/2]port defa    
[Huawei-Ethernet0/0/2]port default vlan 2
Error: The VLAN does not exist.
[Huawei-Ethernet0/0/2]vlan batch 1 2 3 4 5 6 7 
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]port default vlan 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]undo port vlan batch 1 2 3 4 5 6 7
             ^
Error:Ambiguous command found at '^' position.
[Huawei]vlan b 2 3
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]port l a
[Huawei-Ethernet0/0/2]port default vlan 2
[Huawei-Ethernet0/0/2]int e0/0/3
[Huawei-Ethernet0/0/3]port l a
[Huawei-Ethernet0/0/3]port de vlan 3
[Huawei-Ethernet0/0/3]int e0/0/4
[Huawei-Ethernet0/0/4]port l a
[Huawei-Ethernet0/0/4]port de vlan 3j
                                   ^
Error: Wrong parameter found at '^' position.
[Huawei-Ethernet0/0/4]port de vlan 3
[Huawei-Ethernet0/0/4]int e0/0/1
[Huawei-Ethernet0/0/1]port l trunk
[Huawei-Ethernet0/0/1]port trunk allow-pass vlan 2 to 3
[Huawei-Ethernet0/0/1] User interface con0 is available

Please Press ENTER.

<Huawei>reset saved-configuration 
Warning: The action will delete the saved configuration in the device.
The configuration will be erased to reconfigure. Continue? [Y/N]:n
<Huawei>
Dec 30 2022 17:18:00-08:00 Huawei %%01CFM/4/RST_CFG(l)[0]:The user chose N when 
deciding whether to reset the saved configuration.
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/2
[Huawei-GigabitEthernet0/0/2]po li a
[Huawei-GigabitEthernet0/0/2]p d v 2
Error: The VLAN does not exist.
[Huawei-GigabitEthernet0/0/2]vlan batch 1 2
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]vlan batch 1 2 3 4 5 6 
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]port default vlan 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]int g 0/0/3
              ^
Error: Wrong parameter found at '^' position.
[Huawei]int g0/0/3
            ^
Error: Wrong parameter found at '^' position.
[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]int g0/0/3
                      ^
Error: Unrecognized command found at '^' position.
[Huawei-Ethernet0/0/2]int e0/0/2
[Huawei-Ethernet0/0/2]po li a
[Huawei-Ethernet0/0/2]po li a
[Huawei-Ethernet0/0/2]int e0/0/3
[Huawei-Ethernet0/0/3]p l a
[Huawei-Ethernet0/0/3]p d v 3
[Huawei-Ethernet0/0/3]int  g 0/0/1
[Huawei-GigabitEthernet0/0/1]po li t
[Huawei-GigabitEthernet0/0/1]p t a v 2 3
[Huawei-GigabitEthernet0/0/1]q
[Huawei]save
        ^
Error: Unrecognized command found at '^' position.
[Huawei]y
        ^
Error: Unrecognized command found at '^' position.
[Huawei]q
<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]
Error: Please choose 'YES' or 'NO' first before pressing 'Enter'. [Y/N]:y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei> User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei>

lsw2:

The device is running!

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]port l a
[Huawei-Ethernet0/0/2]port defa    
[Huawei-Ethernet0/0/2]port default vlan 2
Error: The VLAN does not exist.
[Huawei-Ethernet0/0/2]vlan batch 1 2 3 4 5 6 7 
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]port default vlan 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]undo port vlan batch 1 2 3 4 5 6 7
             ^
Error:Ambiguous command found at '^' position.
[Huawei]vlan b 2 3
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]port l a
[Huawei-Ethernet0/0/2]port default vlan 2
[Huawei-Ethernet0/0/2]int e0/0/3
[Huawei-Ethernet0/0/3]port l a
[Huawei-Ethernet0/0/3]port de vlan 3
[Huawei-Ethernet0/0/3]int e0/0/4
[Huawei-Ethernet0/0/4]port l a
[Huawei-Ethernet0/0/4]port de vlan 3j
                                   ^
Error: Wrong parameter found at '^' position.
[Huawei-Ethernet0/0/4]port de vlan 3
[Huawei-Ethernet0/0/4]int e0/0/1
[Huawei-Ethernet0/0/1]port l trunk
[Huawei-Ethernet0/0/1]port trunk allow-pass vlan 2 to 3
[Huawei-Ethernet0/0/1] User interface con0 is available

Please Press ENTER.

<Huawei>reset saved-configuration 
Warning: The action will delete the saved configuration in the device.
The configuration will be erased to reconfigure. Continue? [Y/N]:n
<Huawei>
Dec 30 2022 17:18:00-08:00 Huawei %%01CFM/4/RST_CFG(l)[0]:The user chose N when 
deciding whether to reset the saved configuration.
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/2
[Huawei-GigabitEthernet0/0/2]po li a
[Huawei-GigabitEthernet0/0/2]p d v 2
Error: The VLAN does not exist.
[Huawei-GigabitEthernet0/0/2]vlan batch 1 2
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]vlan batch 1 2 3 4 5 6 
Info: This operation may take a few seconds. Please wait for a moment...done.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]p d v 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]port default vlan 2
        ^
Error:Ambiguous command found at '^' position.
[Huawei]int g 0/0/3
              ^
Error: Wrong parameter found at '^' position.
[Huawei]int g0/0/3
            ^
Error: Wrong parameter found at '^' position.
[Huawei]int e0/0/2
[Huawei-Ethernet0/0/2]int g0/0/3
                      ^
Error: Unrecognized command found at '^' position.
[Huawei-Ethernet0/0/2]int e0/0/2
[Huawei-Ethernet0/0/2]po li a
[Huawei-Ethernet0/0/2]po li a
[Huawei-Ethernet0/0/2]int e0/0/3
[Huawei-Ethernet0/0/3]p l a
[Huawei-Ethernet0/0/3]p d v 3
[Huawei-Ethernet0/0/3]int  g 0/0/1
[Huawei-GigabitEthernet0/0/1]po li t
[Huawei-GigabitEthernet0/0/1]p t a v 2 3
[Huawei-GigabitEthernet0/0/1]q
[Huawei]save
        ^
Error: Unrecognized command found at '^' position.
[Huawei]y
        ^
Error: Unrecognized command found at '^' position.
[Huawei]q
<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]
Error: Please choose 'YES' or 'NO' first before pressing 'Enter'. [Y/N]:y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei> User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<Huawei>

R1

The device is running!

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g0/0/2.1
[Huawei-GigabitEthernet0/0/2.1]dotlq termination
                               ^
Error: Unrecognized command found at '^' position.
[Huawei-GigabitEthernet0/0/2.1]dotlq termination vid 2
                               ^
Error: Unrecognized command found at '^' position.
[Huawei-GigabitEthernet0/0/2.1]dot    
[Huawei-GigabitEthernet0/0/2.1]dot1q termin    
[Huawei-GigabitEthernet0/0/2.1]dot1q termination 2
                                                 ^
Error: Unrecognized command found at '^' position.
[Huawei-GigabitEthernet0/0/2.1]ip  add 192.168.129 27
                                       ^
Error: Wrong parameter found at '^' position.
[Huawei-GigabitEthernet0/0/2.1]ip add 192.168.1.129 27
[Huawei-GigabitEthernet0/0/2.1]arp broad    
[Huawei-GigabitEthernet0/0/2.1]arp broadcast enable
Error: This interface is not a termination interface.
[Huawei-GigabitEthernet0/0/2.1]q
[Huawei]
<Huawei>reset saved-configuration 
Warning: The action will delete the saved configuration in the device.
The configuration will be erased to reconfigure. Continue? [Y/N]:n
<Huawei>
Dec 30 2022 17:18:17-08:00 Huawei %%01CFM/4/RST_CFG(l)[0]:The user chose N when 
deciding whether to reset the saved configuration.
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/2.1
[Huawei-GigabitEthernet0/0/2.1]p ad 192.168.1.33 27
                               ^
Error:Ambiguous command found at '^' position.
[Huawei-GigabitEthernet0/0/2.1]ip ad 192.168.1.33 27
[Huawei-GigabitEthernet0/0/2.1]dot1q t v 2
[Huawei-GigabitEthernet0/0/2.1]arp bro en
[Huawei-GigabitEthernet0/0/2.1]int g 0/0/2.2
[Huawei-GigabitEthernet0/0/2.2]ip ad 192.168.1.65 27
[Huawei-GigabitEthernet0/0/2.2]dot1q t v 3
[Huawei-GigabitEthernet0/0/2.2]arp bro en
[Huawei-GigabitEthernet0/0/2.2]dhcp en
Info: The operation may take a few seconds. Please wait for a moment.done.
[Huawei]ip pool 1
Info:It's successful to create an IP address pool.
[Huawei-ip-pool-1]net 192.168.1.32 m 27
[Huawei-ip-pool-1]g 192.168.1.33
[Huawei-ip-pool-1]ip p 2
Info:It's successful to create an IP address pool.
[Huawei-ip-pool-2]net 192.168.1.64 m 27
[Huawei-ip-pool-2]g 192.168.1.65 
[Huawei-ip-pool-2]int g 0/0/2.1
[Huawei-GigabitEthernet0/0/2.1]dhcp select g
[Huawei-GigabitEthernet0/0/2.1]int g 0/0/2.2
[Huawei-GigabitEthernet0/0/2.2]dhcp  select g
[Huawei-GigabitEthernet0/0/2.2]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 192.168.1.1 30
[Huawei-GigabitEthernet0/0/0]int g 0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 192.168.1.5 30
[Huawei-GigabitEthernet0/0/1]q
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]ip rout 192.168.1.12 30 192.168.1.2
[Huawei]ip rout 192.168.1.8 30 192.168.1.6
[Huawei]ip rout 192.168.1.20 30 192.168.1.2
[Huawei]ip rout 192.168.1.20 30 192.168.1.6
[Huawei]ip rout 192.168.1.16 30 192.168.1.2
[Huawei]ip rout 192.168.1.16 30 192.168.1.6
[Huawei]ip rout 192.168.1.96 27 192.168.1.6
[Huawei]ip rout 192.168.1.128 27 192.168.1.6
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 17.
Save the configuration successfully.
<Huawei>
<Huawei>

R2

The device is running!

<Huawei>
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 192.168.1.2 30
[Huawei-GigabitEthernet0/0/0]int g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 192.168.1.13 30
[Huawei-GigabitEthernet0/0/1] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]ip rout 192.168.1.32 27 192.168.1.1
[Huawei]ip rout 192.168.1.64 27 192.168.1.1
[Huawei]ip rout 192.168.1.4 30 192.168.1.1
[Huawei]ip rout 192.168.1.96 27 192.168.1.1
[Huawei]ip rout 192.168.1.96 27 192.168.1.14
[Huawei]ip rout 192.168.1.128 27 192.168.1.1
[Huawei]ip rout 192.168.1.128 27 192.168.1.14
[Huawei]ip rout 192.168.1.8 30 192.168.1.14
[Huawei]ip rout 192.168.1.20 30 192.168.1.14
[Huawei]ip rout 192.168.1.16 30 192.168.1.14
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>
<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 17.
Save the configuration successfully.
<Huawei>
<Huawei>

R3

The device is running!

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g0/0/2.1
[Huawei-GigabitEthernet0/0/2.1]ip ad 192.168.1.97 27
[Huawei-GigabitEthernet0/0/2.1]d t v 2
[Huawei-GigabitEthernet0/0/2.1]a b en
[Huawei-GigabitEthernet0/0/2.1]int g 0/0/2.2
[Huawei-GigabitEthernet0/0/2.2]ip ad 192.168.1.129 27
[Huawei-GigabitEthernet0/0/2.2]d t v 3
[Huawei-GigabitEthernet0/0/2.2]a b en
[Huawei-GigabitEthernet0/0/2.2]dhcp en
Info: The operation may take a few seconds. Please wait for a moment.done.
[Huawei]ip pool 1
Info:It's successful to create an IP address pool.
[Huawei-ip-pool-1]net 192.168.1.96 m 27
[Huawei-ip-pool-1]g 192.168.1.97
[Huawei-ip-pool-1]ip pool 2
Info:It's successful to create an IP address pool.
[Huawei-ip-pool-2]net 192.168.1.128 m 27
[Huawei-ip-pool-2]g 192.168.1.129
[Huawei-ip-pool-2]int g 0/0/2.1
[Huawei-GigabitEthernet0/0/2.1]dhcp se g 
[Huawei-GigabitEthernet0/0/2.1]int g 0/0/2.2
[Huawei-GigabitEthernet0/0/2.2]dhcp se g 
[Huawei-GigabitEthernet0/0/2.2]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 192.168.1.6 30
[Huawei-GigabitEthernet0/0/0]int g 0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 192.168.1.9 30
[Huawei-GigabitEthernet0/0/1]q
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei] un in e
Info: Information center is disabled.
[Huawei]
[Huawei]ip rout 192.168.1.32 27 192.168.1.5
[Huawei]ip rout 192.168.1.64 27 192.168.1.5
[Huawei]ip rout 192.168.1.0 30 192.168.1.5
[Huawei]ip rout 192.168.1.12 30 192.168.1.10
[Huawei]ip rout 192.168.1.20 30 192.168.1.10
[Huawei]ip rout 192.168.1.16 30 192.168.1.10
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]dis    
[Huawei]display ip    
[Huawei]display ip-subnet-vlan
                               ^
Error:Incomplete command found at '^' position.
[Huawei]dis ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 16       Routes : 16       

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
    192.168.1.0/30  Static  60   0          RD   192.168.1.5     GigabitEthernet
0/0/0
    192.168.1.4/30  Direct  0    0           D   192.168.1.6     GigabitEthernet
0/0/0
    192.168.1.6/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
    192.168.1.8/30  Direct  0    0           D   192.168.1.9     GigabitEthernet
0/0/1
    192.168.1.9/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
   192.168.1.12/30  Static  60   0          RD   192.168.1.10    GigabitEthernet
0/0/1
   192.168.1.16/30  Static  60   0          RD   192.168.1.10    GigabitEthernet
0/0/1
   192.168.1.20/30  Static  60   0          RD   192.168.1.10    GigabitEthernet
0/0/1
   192.168.1.32/27  Static  60   0          RD   192.168.1.5     GigabitEthernet
0/0/0
   192.168.1.64/27  Static  60   0          RD   192.168.1.5     GigabitEthernet
0/0/0
   192.168.1.96/27  Direct  0    0           D   192.168.1.97    GigabitEthernet
0/0/2.1
   192.168.1.97/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/2.1
  192.168.1.128/27  Direct  0    0           D   192.168.1.129   GigabitEthernet
0/0/2.2
  192.168.1.129/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/2.2

[Huawei]display this
#
sysname Huawei
#
undo info-center enable
#
dhcp enable
#
ip route-static 192.168.1.0 255.255.255.252 192.168.1.5
ip route-static 192.168.1.12 255.255.255.252 192.168.1.10
ip route-static 192.168.1.16 255.255.255.252 192.168.1.10
ip route-static 192.168.1.20 255.255.255.252 192.168.1.10
ip route-static 192.168.1.32 255.255.255.224 192.168.1.5
ip route-static 192.168.1.64 255.255.255.224 192.168.1.5
#
return
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 17.
Save the configuration successfully.
<Huawei>

R4

The device is running!

<Huawei>
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 192.168.1.14 30
[Huawei-GigabitEthernet0/0/0]int g 0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 192.168.1.10 30
[Huawei-GigabitEthernet0/0/1]int g 0/0/3
[Huawei-GigabitEthernet0/0/3]ip ad 192.168.1.21 30
[Huawei-GigabitEthernet0/0/3]int g0/0/2
[Huawei-GigabitEthernet0/0/2]ip ad 192.168.1.17 30
[Huawei-GigabitEthernet0/0/2]q
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]ip rout 192.168.1.0 30 192.168.1.13
[Huawei]ip rout 192.168.1.4 30 192.168.1.9
[Huawei]ip rout 192.168.1.32 27 192.168.1.9
[Huawei]ip rout 192.168.1.32 27 192.168.1.13
[Huawei]ip rout 192.168.1.64 27 192.168.1.9
[Huawei]ip rout 192.168.1.64 27 192.168.1.13
[Huawei]ip rout 192.168.1.96 27 192.168.1.9
[Huawei]ip rout 192.168.1.128 27 192.168.1.9
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]
Error: Please choose 'YES' or 'NO' first before pressing 'Enter'. [Y/N]:y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 17.
Save the configuration successfully.
<Huawei>
<Huawei>

R5

Please press enter to start cmd line!

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 192.168.1.22 30
[Huawei-GigabitEthernet0/0/0]int g 0/0/2
[Huawei-GigabitEthernet0/0/2]ip ad 192.168.1.18 30
[Huawei-GigabitEthernet0/0/2]int g 0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 12.1.1.1 24
[Huawei-GigabitEthernet0/0/1] User interface con0 is available

Please Press ENTER.

<Huawei>sy 
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]ip rout 192.168.1.32 27 192.168.1.21
[Huawei]ip rout 192.168.1.32 27 192.168.1.17
[Huawei]ip rout 192.168.1.64 27 192.168.1.21
[Huawei]ip rout 192.168.1.64 27 192.168.1.17
[Huawei]ip rout 192.168.1.96 27 192.168.1.21
[Huawei]ip rout 192.168.1.96 27 192.168.1.17
[Huawei]ip rout 192.168.1.128 27 192.168.1.21
[Huawei]ip rout 192.168.1.128 27 192.168.1.17
[Huawei]ip rout 192.168.1.4 30 192.168.1.17
[Huawei]ip rout 192.168.1.4 30 192.168.1.21
[Huawei]ip rout 192.168.1.0 30 192.168.1.17
[Huawei]ip rout 192.168.1.0 30 192.168.1.21
[Huawei]ip rout 192.168.1.12 30 192.168.1.17
[Huawei]ip rout 192.168.1.12 30 192.168.1.21
[Huawei]ip rout 192.168.1.8 30 192.168.1.17
[Huawei]ip rout 192.168.1.8 30 192.168.1.21
[Huawei] User interface con0 is available

Please Press ENTER.

<Huawei>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
Now saving the current configuration to the slot 17.
Save the configuration successfully.
<Huawei>
<Huawei>
<Huawei>

R6

The device is running!

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]un in e
Info: Information center is disabled.
[Huawei]int g 0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad 12.1.1.2 24
[Huawei-GigabitEthernet0/0/0]int g 0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad 1.1.1.254 24
[Huawei-GigabitEthernet0/0/1] User interface con0 is available

Please Press ENTER.

<Huawei>
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei] un in e
Info: Information center is disabled.
[Huawei]ip rout 192.168.1.32 27 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.64 27 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.96 27 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.128 27 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.4 30 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.0 30 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.12 30 192.168.1.17 pre 70
[Huawei]
[Huawei]ip rout 192.168.1.8 30 192.168.1.17 pre 70
[Huawei] User interface con0 is available

Please Press ENTER.
 

dhcp自动获取IP信息

www.beixin.com来访问http服务器

备敢为人先
关注
专栏目录
H3C学习笔记《三》（错误提示信息）
weixin_34122604的博客
08-19 3861
1、错误提示信息 [Router]di ^ % Ambiguous command found at '^' position. 在^处发现了模棱两可的命令。 [Router]dispaly ^ % Unrecognized command found at '^' position. 在^处未发现命令 [Rout...
理论+实验 hybrid虚拟局域网实验-hybrid-路由综合实验
Lfwthotpt的博客
11-08 1898
华为设备配置vlan 将接口加入accesskou 将接口加入trunk口 vlan的基本概念 hybrid工作原理 <Huawei> <Huawei>sys <Huawei>system-view '进入系统视图' Enter system view, return user view with Ctrl+Z. [Huawei]u...
华为设备配置篇——VRRP配置（虚拟路由冗余）
最新发布
ZL_1618的博客
09-06 1862
VRRP可以监视上行端口的状态，当设备感知上行端口或者链路发生故障时，可以主动的降低VRRP的优先级，从而保证上行链路正常的backup设备能够通过选举切换成Master状态，指导报文转发。接入交换机为SW1，核心交换机为SW2和SW3，SW2与SW3做一个VRRP路由冗余。除此之外PC1能够正常的访问到Inetrnet，拓扑如下：1.PC1配置地址：192.168.10.1 网关：192.168.10.2542.配置接入交换机SW1。
华为设备 命令行的错误提示
weixin_48776593的博客
01-30 4450
(error:误差,)（found:找到,）（position:定位,（command:控制,）（wrong:不合适,（parameter:范围,
2021-1-14HCIP第二天
m0_53102443的博客
01-14 291
交换部分： 企业网三层架构： 接入层-提供端口密度，用于用户的就近接入汇聚层（分布层）— 流量的聚合 – VLAN STP SVI HSRP VRRP CHENNL… 核心层 高速转发—路由-NAT冗余—备份 设备冗余 线路冗余 网关冗余 UPS电源冗余VLAN ：虚拟局域网 逻辑的将一个广播域切分为多个；配置思路：交换机上创建vlan编号0-4095 4096个 其中1-4094可用 12位二进制构成 默认存在VLAN1,且默认的所有接口属于vlan1 [Huawei]vlan
关于华为ensp一些报错处理分享及基础命令
热门推荐
所爱的博客
08-31 6万+
1.Error: Unrecognized command found at '^' position. 这里会发现在输入sys按TAb键时不会自动补全，那我们这是就应该反应过来，肯定是哪里有问题了，比如输入system-view时报错，你注意看是<>还是[]了吗，[]时输入system-view是错误的，也不会自动补全，解决方法是ctrl+z，其实他下面也有提示 后来我发现是视图的原因 eNSP有种视图模式 : 用户视图 | 系统视图 | 接口视图 ...
eNsp的路由器启动失败——检查过程
datefate的博客
03-29 3336
首先，按照eNSP的文档排查过一遍后无法解决。 关闭win10的Hyper-V无法解决。 卸载所有组件重装，没有解决。 打开VM VirtualBox ，尝试打开虚拟电脑。如果打不开，报： Virtual Box 虚拟机无法启动：VERR_SUPDRV_NO_RAW_MODE_HYPER_V_ROOT 那么问题就是VM的了，卸载掉Vbox win键+R打开运行，输入regedit，回...
hcia综合实验（仅供参考）
07-18
设计链路聚合，ospf，stp生成树，不同vlan间的通信，适合华为认证初学者参考。
华为模拟器eNSP-HCIA综合实验2
01-04
【华为模拟器eNSP-HCIA综合实验2】是一个基于华为网络设备的教育实践项目，旨在帮助学习者深入理解并掌握HCIA（华为认证ICT助理）级别的网络基础知识。在这个实验中，你将通过华为eNSP（Enterprise Network ...
华为模拟器eNSP练习题-HCIA综合实验
01-04
【华为模拟器eNSP练习题-HCIA综合实验】是一个针对华为认证HCIA（Huawei Certified ICT Associate）级别的实践训练，旨在帮助学习者熟悉网络基础及华为设备的配置与管理。eNSP（Enterprise Network Simulation ...
HCIA 综合实验
qq_52253798的博客
04-09 605
一、 实验题目及其要求 1、由实验的题目要求进行IP地址的规划； 同时进行相应的拓扑搭建。 2、划分VLAN R1为例相应配置如下： <Huawei>system-view [Huawei]interface GigabitEthernet 0/0/1.1 [Huawei-GigabitEthernet0/0/1.1]ip address 192.168.1.65 27 [Huawei-GigabitEthernet0/0/1.1]q [Huawei]interface...
HCIA综合实验（五）
01-09
实验目的及要求：HCIA全部知识点，全网可通 具体是实现会一一介绍 本人已经将全部做完的实验拓扑保存：链接：https://pan.baidu.com/s/1l8JlXiJlWJIhNNNswxY9tQ 提取码：y1j5 配置思想： 首先从最低层开始进行配置 ...
华为S5720S重置密码
Adrian的博客
04-14 2万+
s5720s重置密码
单臂路由配置
qq_44933518的博客
04-22 7432
1.实现不同vlan的通信的方法之一：单臂路由，通过二层交换机配合路由器来实现路由转发。这个实验利用单臂路由，使得处于vlan 2的PC1 能和处于vlan 3的PC2能通信 实验前须知： dot1q是IEEE 802.1q协议的缩写，dot是点的意思 dot1q termination vid 2的意思是：该子接口在收到带有vlan tag（此处是vlan 2）的报文时，将剥离tag进行三层转...
qt dependant doesn not exist错误的解决方法
Done Lin的专栏
08-10 1万+
qt dependant doesn not exist.在编写QT程序的时候，我不需要资源，于是通过QtCreator工程左边栏目，右键删除，之后编译出现： error qt dependant doesn not exist要解决这个问题，要删除资源，然后再清除项目，最后工程栏里面右键执行qmake。 之后重新构建整个项目即可；
U3D 串口通信IOException: The port `COM11' does not exist.问题
印心石屋
03-24 3726
Unity打开串口方式不一样，因为在.NET2.0打开串口时，如果串口超过10，则必须在前面加上“\\?\”，比如我需要打开COM301，在Unity中你实际传给串口的参数必须是“”\\?\” + “COM301””
The connection does not exist.
sinat_15347975的博客
08-22 2769
问题:当服务放置一段时间后，再次调用会提示:The connection does not exist.; nested exception is java.sql.SQLException: The connection does not exist.一直不知如何解决，直到看到了这篇博文才有了解决问题的思路。 解决方案:之前我在tomcat7/conf/context.xml下是这样配置jndi
交换机接口的三种模式，生成树协议，实验题
Ryougi_Shiki_uio的博客
04-08 2148
目录交换机接口的三种模式1.access接口模式（接入链路，接入模式）2.trunk接口模式（中继模式，放通多个vlan）3.hybrid接口模式（混杂模式，混合模式）STP生成树协议1.stp生成树协议的介绍2.stp算法的步骤实验题1.实验一实验二 交换机接口的三种模式 1.access接口模式（接入链路，接入模式） 接收数据：当接收到一个无标记帧的时候，打上自己的PVid并接受（就是自己的vlan标签）。当接收到一个有标记帧的时候，对比自己的pvid，如果相同就接收，不同就丢弃。 发送数据：发送的时候
光棍节一天让我郁闷的一件事 Vlan划分
meng13673934514的专栏
11-11 794
SW1：192.168.0.2     CLI session with the switch is open.     To end the CLI session, enter [Exit]. Switch>%LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down%LINEPROTO-5-UPDOWN: Lin
hcia综合实验案例
07-28
关于HCIA综合实验案例，我可以为您提供一些相关信息。HCIA（华为认证网络工程师）是华为推出的一项网络工程师认证培训项目，旨在培养和评估网络工程师的专业技能。 HCIA综合实验案例是HCIA认证考试中的一部分，通过...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值