实验要求
1.除了R5的环回地址固定5.5.5.0/24,其他网段基于192.168.1.0/24进行合理划分;
2.R1-R4每个路由器存在两个环回接口,模拟pc,地址也在192.168.1.0/24网络内;
3.R1-R4不能直接编写到达5.5.5.0/24的静态路由,但依然可以访问;
4.全网可达,尽量减少每台路由器路由条目数量,避免环路;
5.R4与R5间,正常1000M链路通信,故障时自动改为100M;
拓扑图
实验思路:.
1、划分IP (划分IP的方式有多种,以下期分方式呼做为参考),并
给相应设备配置IP地址。,
分析:纵观整个网络拓扑(包括环回网段,考虑汇总),可将
192.168.1.0/24划分为5个大的网段。
(1) 192. 168.1.0/27---骨干链路。
分析:骨干链路有6条,继续将192.168.1.0/27 网段,划分成6个小网
段。30位的掩码。也可保证每条链路只有两个IP地址可配,节约IP
地址。。
192.168.1.0/30
192.168.1.4/30
192.168.1.8/30
192.168.1.12/30
192.168.1.16/30
192.168.1.20/30
(2) 192.168.1.32/27----R1 环回。
分析:考虑到环回地址,最后需要汇总,故为了汇总方便,可将
192. 168.132/27继续划分出两个连续的小网段,分别给两个环回口,同理R2/R3/R4的环回划分也是一样的思想。。
L0: ...192.168.1.32/28
L1......192.168.1.48/28
(3) 192.168.1.64/27----R2环回。
L0: 192.168.1.64/28
L1:.... 192.168.1.80/28
(4) 192.168.1.96/2----R3环回,
LO: ...192.168.1.96/28.
L1:....192.168.1.112/28
(5) 192.168.1.128/27----R4环回。
(3) 192.168.1.64/27----R2环回,
L0: ..192.168.1.64/28
L1...-192.168.1.80/28
(4) 192.168.1.96/27----R3环回,
L0:
...192.168.1.96/28
L1....192.168.1.112/28
(5) 192.168.1.128/27----R4环回。
L0: ... 192.168.1.128/28
L1..192.168.1.144/28.
2、编写除了到达5.5.5.0/24之外,到达其他网段的静态路由。
3、配置缺省路由,实现5.5.5.0/24互通,至此实现全网通,并测试
4、防环,做黑洞路由配置|
5、做备份,通过改变路由条目优先级实现.
6、测试,观察1000Mb/s链路故障时,数据能否走100Mb/s链路。。
实验步骤.
l、配置IP地址。
[R l]intg0/0/0.
[R1-GigabitEthernet0/0/0]ip*add-192.168.1.1-30
[R l-GigabitEthernet0/0/0]int g0/0/1.
[R l-GigabitEthernet0/0/l]ip*add192.168.1.5-30.
[R1]intl0.
[R1-LoopBack0]ipadd-192. 168.1.33-28.
[Rl-LoopBack0]int'll.
[R2 ]int:g0/0/0.
[R2-GigabitEthernet0/0/0]ip*add192.168.1.2-30
[R2-GigabitEthernet0/0/0]int:g0/0/1.
[R2-GigabitEthernet0/0/1 ]ip*add-192.168 1,9 30
[R2]int10.
[R2-LoopBack0]ip*add- 192. 168.1.65-28.
[R2-LoopBack0]int:ll.
[R2-LoopBack1 ]ipradd 192.168.1.8128
。。。。。。
(r1)ip route-s
ip route-s
ip route-static 192.168.1.8 30 192.168.1.2
ip route-static 192.168.1.64 27 192.168.1.2
ip route-s
ip route-static 192.168.1.128 27 192.168.1.2
ip route-static 192.168.1.128 27 192.168.1.6
ip route-s
ip route-static 192.168.1.16 30 192.168.1.2
ip route-static 192.168.1.16 30 192.168.1.6
ip route-static 192.168.1.20 30 192.168.1.2
ip route-static 192.168.1.20 30 192.168.1.6
ip route-s
ip route-static 192.168.1.12 30 192.168.1.6
ip route-static 192.168.1.96 27 192.168.1.6
(r2)
ip route-s
ip route-static 192.168.1.128 27 192.168.1.10
ip route-static 192.168.1.16 30 192.168.1.10
ip route-static 192.168.1.20 30 192.168.1.10
ip route-static
192.168.1.12 30 192.168.1.10
iproute-static 192. 168.1.9627 192. 168.1.10
ip route-static 192.168.1.96 27 192.168.1.1
ip route-s
ip route-static 192.168.1.4 30 192.168.1.1
ip route-static 192.168.1.32 27 192.168.1.1
打累了(r3-r5.....)
查看配置与验证通信:
以r1为例测试
放过我吧,累了,来个鸭蛋垫垫