实验报告
一、拓扑信息
二、实验要求
1、R5为ISP,只能进行IP地址配置;其所有地址均配为公有IP地址
2、R1和R5间使用PPP的PAP认证,R5为主认证方2;
R2于R5之间使用PPP的chap认证,R5为主认证方;
R3于R5之间使用HDLC封装。
3、R1/R2/R3构建一个MGRE环境,R1为中心站点;R1、R4间为点到点的GRE。
4、整个私有网络基于RIP全网可达
5、所有Pc设置私有IP为源IP,可以访问R5环回。
三、实验思路
1、为所有路由器设备进行IP配置
2、R1和R5进行PPP的PAP认证; R2于R5之间使用PPP的chap认证; R3于R5之间使用HDLC封装。
3、构建MGRE环境;构建GRE
4、RIP全网可达
5、PC访问R5
四、实验过程
1、为所有路由器设备进行IP配置
R1:
[R1]int g 0/0/0
[R1-GigabitEthernet0/0/0]ip address 192.168.1.1 24
[R1]interface Serial 4/0/0
[R1-Serial4/0/0]ip address 15.0.0.1 24
[R1]int t 0/0/0
[R1-Tunnel0/0/0]ip add 192.168.5.1 24
[R1]int t 0/0/1
[R1-Tunnel0/0/1]ip add 192.168.6.1 24
缺省路由:
[r1]ip route-static 0.0.0.0 0 15.0.0.2
R2:
[R2]int g 0/0/0
[R2-GigabitEthernet0/0/0]ip address 192.168.2.1 24
[R2]int s 4/0/0
[R2-Serial4/0/0]ip add 25.0.0.1 24
[R2]int t 0/0/0
[R2-Tunnel0/0/0]ip add 192.168.5.2 24
缺省路由:
[r2]ip route-static 0.0.0.0 0 25.0.0.2
R3:
[R3]int g 0/0/0
[R3-GigabitEthernet0/0/0]ip address 192.168.3.1 24
[R3]int s 4/0/0
[R3-Serial4/0/0]ip add 35.0.0.1 24
[R3]int t 0/0/0
[R3-Tunnel0/0/0]ip add 192.168.5.3 24
缺省路由:
[r3]ip route-static 0.0.0.0 0 35.0.0.2
R4:
[R4]int g 0/0/1
[R4-GigabitEthernet0/0/1]ip address 192.168.4.1 24
[R4]int g 0/0/0
[R4-GigabitEthernet0/0/0]ip add 45.0.0.1 24
[R4]int t 0/0/0
[R4-Tunnel0/0/0]ip add 192.168.6.2 24
缺省路由:
[r4]ip route-static 0.0.0.0 0 45.0.0.2
2、
-
R1和R5进行PPP的PAP认证
认证方配置: [R5]aaa [R5-aaa]local-user huawei password cipher 123456 [R5-aaa]local-user huawei service-type ppp [R5-aaa]int s3/0/0 [R5-Serial3/0/0]ppp authentication-mode pap 被认证方配置: [R1]int s4/0/0 [R1-Serial4/0/0]ppp pap local-user huawei password cipher 123456
-
R2于R5之间使用PPP的chap认证
认证方配置: [R5-aaa]local-user admin password cipher 123456 [R5-Serial3/0/0]int s3/0/1 [R5-Serial3/0/1]ppp authentication-mode chap 被认证方配置: [R2]int s4/0/0 [R2-Serial4/0/0]ppp chap user admin [R2-Serial4/0/0]ppp chap password cipher 123456
-
R3于R5之间使用HDLC封装
直接修改串口接口的数据链路层协议为非标准的HDLC [R5-Serial4/0/0]link-protocol hdlc [R3-Serial4/0/0]link-protocol hdlc
3、构建MGRE环境;构建GRE
-
构建MGRE环境
中心配置
R1: [R1]int t 0/0/1 [R1-Tunnel0/0/0]tunnel-protocol gre p2mp ---修改接口的封装协议为MGRE [R1-Tunnel0/0/0]source 15.0.0.1 ---规定封装源15.0.0.1 [R1-Tunnel0/0/0]nhrp network-id 100 ---创建NHRP域
分支配置
R2: [R2]int t 0/0/0 [R2-Tunnel0/0/0]tunnel-protocol gre p2mp ---修改接口的封装协议为MGRE [R2-Tunnel0/0/0]source s4/0/0 ---规定封装源s4/0/0接口的IP地址 [R2-Tunnel0/0/0]nhrp network-id 100 ---加入中心创建的NHRP域 [R2-Tunnel0/0/0]nhrp entry 192.168.5.1 15.0.0.1 register ----找中心上报映射信息(第一个IP为隧道地址,第二个为物理地址)
R3配置与R2一样: [R3]int t 0/0/0 [R3-Tunnel0/0/0]ip add 192.168.5.3 24 [R3-Tunnel0/0/0]tunnel-protocol gre p2mp [R3-Tunnel0/0/0]source s4/0/0 [R3-Tunnel0/0/0]nhrp network-id 100 [R3-Tunnel0/0/0]nhrp entry 192.168.5.1 15.0.0.1 register
查看它们之间的映射关系
-
构建GRE
R1: [R1-Tunnel0/0/1]tunnel-protocol gre [R1-Tunnel0/0/1]source 15.0.0.1 ---定义封装中的源地址信息 [R1-Tunnel0/0/1]destination 45.0.0.1 ---定义封装中的目的地址信息
R4: [R4-Tunnel0/0/0]tunnel-protocol gre [R4-Tunnel0/0/0]source 45.0.0.1 [R4-Tunnel0/0/0]destination 15.0.0.1
4、RIP全网可达
R1配置:
[R1-Tunnel0/0/0]nhrp entry multicast dynamic ---在中心开启伪广播功能
[R1]rip 1
[R1-rip-1]version 2
[R1-rip-1]network 192.168.1.0 ---主类宣告
[R1-rip-1]network 192.168.5.0
[R1-rip-1]network 192.168.6.0
R2配置:
[R2]rip 1
[R2-rip-1]version 2
[R2-rip-1]network 192.168.2.0
[R2-rip-1]network 192.168.5.0
R3配置:
[R3-rip-1]rip 1
[R3-rip-1]version 2
[R3-rip-1]network 192.168.3.0
[R3-rip-1]network 192.168.5.0
R4配置:
[R4]rip 1
[R4-rip-1]version 2
[R4-rip-1]network 192.168.4.0
[R4-rip-1]network 192.168.6.0
检查路由表
5、PC访问R5
PC的配置
配置Easy IP
[R1-rip-1]acl 2000
[R1-acl-basic-2000]rule 10 permit source 192.168.1.0 0.0.255.255
[R1-acl-basic-2000]q
[R1]int s4/0/0
[R1-Serial4/0/0]nat outbound 2000
[R2]acl 2000
[R2-acl-basic-2000]rule 10 permit source 192.168.2.0 0.0.0.255
[R2-acl-basic-2000]int s4/0/0
[R2-Serial4/0/0]nat outb 2000
[R3]acl 2000
[R3-acl-basic-2000]rule 10 permit source 192.168.3.0 0.0.0.255
[R3-acl-basic-2000]int s4/0/0
[R3-Serial4/0/0]nat out 2000
[R4]acl 2000
[R4-acl-basic-2000]rule 10 permit source 192.168.4.0 0.0.0.255
[R4-acl-basic-2000]int g0/0/0
[R4-GigabitEthernet0/0/0]nat out 2000
检查路由表
PCpingR5