利用arduino采集温湿度，客户端程序显示实时曲线图

最新推荐文章于 2024-07-17 09:42:12 发布

xiaoereee

最新推荐文章于 2024-07-17 09:42:12 发布

阅读量6.9k

点赞数 3

本文链接：https://blog.csdn.net/xiaoereee/article/details/55510167

版权

该博客介绍了如何使用arduino单片机采集温湿度数据，并通过客户端程序展示实时曲线图，提供了单片机程序和客户端界面代码。

摘要由CSDN通过智能技术生成

// Example testing sketch for various DHT humidity/temperature sensors
// Written by ladyada, public domain

#include "DHT.h"

#define DHTPIN 2     // what digital pin we're connected to

// Uncomment whatever type you're using!
#define DHTTYPE DHT11   // DHT 11
//#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
//#define DHTTYPE DHT21   // DHT 21 (AM2301)

// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor

// Initialize DHT sensor.
// Note that older versions of this library took an optional third parameter to
// tweak the timings for faster processors.  This parameter is no longer needed
// as the current DHT reading algorithm adjusts itself to work on faster procs.
DHT dht(DHTPIN, DHTTYPE);

void setup() {
  Serial.begin(9600);
  Serial.println("DHTxx test!");

  dht.begin();
}

void loop() {
  // Wait a few seconds between measurements.
  delay(2000);

  // Reading temperature or humidity takes about 250 milliseconds!
  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
  float h = dht.readHumidity();
  // Read temperature as Celsius (the default)
  float t = dht.readTemperature();
  // Read temperature as Fahrenheit (isFahrenheit = true)
  float f = dht.readTemperature(true);

  // Check if any reads failed and exit early (to try again).
  if (isnan(h) || isnan(t) || isnan(f)) {
    Serial.println("Failed to read from DHT sensor!");
    return;
  }

  // Compute heat index in Fahrenheit (the default)
  float hif = dht.computeHeatIndex(f, h);
  // Compute heat index in Celsius (isFahreheit = false)
  float hic = dht.computeHeatIndex(t, h, false);

 // Serial.print("Humidity: ");
  Serial.print("ST");
  Serial.print(h);
 // Serial.print(" %\t");
 // Serial.print("Temperature: ");
    Serial.print(t);
//  Serial.print(" *C ");
    Serial.print(f);
//  Serial.print(" *F\t");
//  Serial.print("Heat index: ");
//  Serial.print(hic);
//  Serial.print(" *C ");
//  Serial.print(hif);
//  Serial.println(" *F");
}

以上是arduino单片机程序网上找别人的

以下是客户端界面和代码

using System;
using System.Collections.Generic;
using System.ComponentModel;
using System.Data;
using System.Drawing;
using System.Linq;
using System.Text;