5G中定时器

5G（NR）网络无线资源控制(RRC)中引入了下列计时器、计数器和常量，以便UE在RRC setuprequest, RRC reestablishment, RRC resume, RRC suspend等进程的可靠运行。
RRC计时器，指示计时器持续时间及在事件中何时开始和停止；如果计时器超时，UE将采取的行动。这些计时器由字母“T”表示，后跟3位数字，例如 T300。每个计时器起始值为零；UE应用的计时器值倒计数为零时，则计为超时；除非明确说明另有规定。 Timer: T300 Start Point:（起始点） Upon transmission of RRCSetupRequest Stop Point:（结束点） Upon reception of RRCSetup or RRCReject message Upon Cell re-selection Upon abortion of connection establishment by upper layers Action upon Timer Expiry:（超时后续动作） Timer: T301 Start Point:（起始点） Upon transmission of RRCReestabilshmentRequest Stop Point:（结束点） Upon reception of RRCReestablishment or RRCSetupmessage when the selected cell becomes unsuitable Action upon Timer Expiry:（超时后续动作） Go to RRC-IDLE Timer: T302 Start Point:（起始点） Upon reception of RRCReject while performing RRC connection establishment or resume, Upon reception of RRCRelease with waitTime Stop Point:（结束点） Upon entering RRC-CONNECTED or RRC-IDLE Upon cell re-selection Upon reception of RRCReject message Action upon Timer Expiry:（超时后续动作） Inform upper layers about barring alleviation Timer: T304 Start Point:（起始点） Upon detecting physical layer problems for the SpCell i.e. upon receiving N310 consecutive out-of sync indications from lower layers Stop Point:（结束点） Upon receiving N311 consecutive in-sync indications from lower layers for the SpCell, Upon receiving RRCReconfiguration with reconfiguration With Sync for that cell group, and upon initiating the connection re-establishment procedure. Upon SCG release, if the T310 is kept in SCG Action upon Timer Expiry:（超时后续动作） If the T310 is kept in MCG: If security is not activated: go to RRC_IDLE else: initiate the connection re-establishment procedure If the T310 is kept in SCG, Inform E-UTRAN/NR about the SCG radio link failure by initiating the SCG failure information procedure as specified in 5.7.3 of specification 38.331 Timer: T311 Start Point:（起始点） Upon initiating the RRC connection reestablishment procedure Stop Point:（结束点） Upon selection of a suitable NR cell or a cell using another RAT Action upon Timer Expiry:（超时后续动作） Enter RRC_IDLE Timer: T319 Start Point:（起始点） Upon transmission of RRCResumeRequest Stop Point:（结束点） Upon reception of RRCResume, RRCSetup, RRCRelease, RRCRelease with suspendConfig or RRCReject message, cell re-selection Upon abortion of connection establishment by upper layers Action upon Timer Expiry:（超时后续动作） Perform the actions as specified in 5.3.13.5 of 3GPP specification 38.331 Timer: T320 Start Point:（起始点） Upon reception of t320 upon cell (re)selection to NR from another RAT with validity time configured for dedicated priorities (in which case the remaining validity time is applied) Stop Point:（结束点） Upon entering RRC-CONNECTED, Upon reception of RRC Release, when PLMN selection is performed on request by NAS Upon cell (re)selection to another RAT (in which case the timer is carried on to the other RAT) Action upon Timer Expiry:（超时后续动作）Discard the cell re-selection priority information provided by dedicated signalling Timer: T321 Start Point:（起始点） Upon receiving measConfig including a reportConfig with the purpose set to report CGI Stop Point:（结束点） Upon acquiring the information needed to set all fields of cgiinfo Upon receiving measConfig that includes removal of the reportConfig with the purpose set to reportCGI upon detecting that a cell is not broadcasting SIB1 Action upon Timer Expiry:（超时后续动作） Initiate the measurement reporting procedure, stop performing the related measurements and remove the corresponding measId Timer: T325 Start Point:（起始点） Upon reception of RRCRelease message with deprioritisationTimer Action upon Timer Expiry:（超时后续动作） Stop deprioritisation of all frequencies or NR signalled by RRCRelease Timer: T380 Start Point:（起始点） Upon reception of RRCRelease including suspendConfig Stop Point:（结束点） Upon reception of RRCResume, RRCSetup or RRCRelease Action upon Timer Expiry:（超时后续动作） Perform the actions as specified in 5.3.13 of 3GPP 38.331 Timer: T390 Start Point:（起始点） When access attempt is barred at access barring check for an Access Category The UE shall maintain one instance of this timer per Access Category Stop Point:（结束点） As specified in 5.3.14.3 of 3GPP 38.331 Action upon Timer Expiry:（超时后续动作） Perform the actions as specified in 5.3.14.4 of 3GPP 38.331 Timer: T3xx Start Point:（起始点） Upon transmitting UEAssistanceInformation message with DelayBudgetReport Stop Point:（结束点） Upon initiating the connection re-establishment procedures Action upon Timer Expiry:（超时后续动作） No action. RRC常量和计数器：计数与否或针对特定事件尝试。计数器用字母“n”表示，后面跟着3个数字。例如 n310。 N310: Maximum number of consecutive “out-of-sync” indications for the PCell received from lower layers Reset Upon reception of “insync” indication from lower layers Upon receiving RRCReconfiguration with reconfigurationWithSync for that cell group Upon initiating the connection reestablishment procedure Incremented Upon reception of “out-of-sync” from lower layer while the timer T310 is stopped When reaching max value Start timer T310 N311: Maximum number of consecutive “in-sync” indications for the PCell received from lower layers Reset Upon reception of “outof-sync” indication from lower layers Upon receiving RRCReconfiguration with reconfigurationWithSync for that cell group Upon initiating the connection reestablishment procedure Incremented Upon reception of the “in-sync”from lower layer while the timer T310 is running When reaching max value Stop the timer T310原文来自：http://www.techplayon.com/5g-nr-rrc-timers-counters-and-constants/
t319是rrc的挂起，t320到异系统的重选！t321是anr中的cgi上报，t380释放挂起的rrc，t390是小区rrc禁止链接（bar）的时间