GD32F407VET6配置系统时钟的方法

1.外部晶振使用8M
2.修改例程gd32f4xx.h

/* define value of high speed crystal oscillator (HXTAL) in Hz */
#if !defined  (HXTAL_VALUE)
#define HXTAL_VALUE    ((uint32_t)8000000)

将系统默认的25000000改为8000000

2.在system_gd32f4xx.c中修改为如下代码

#include "gd32f4xx.h"

/* system frequency define */
#define __IRC16M          (IRC8M_VALUE)            /* internal 16 MHz RC oscillator frequency */
#define __HXTAL           (HXTAL_VALUE)             /* high speed crystal oscillator frequency */
//#define __SYS_OSC_CLK     (__IRC16M)                /* main oscillator frequency */

#define __SYS_OSC_CLK     (__HXTAL)

/* select a system clock by uncommenting the following line */
//#define __SYSTEM_CLOCK_IRC16M                   (uint32_t)(__IRC16M)
//#define __SYSTEM_CLOCK_HXTAL                    (uint32_t)(__HXTAL)
//#define __SYSTEM_CLOCK_120M_PLL_IRC16M          (uint32_t)(120000000)
//#define __SYSTEM_CLOCK_120M_PLL_8M_HXTAL          (uint32_t)(120000000)
//#define __SYSTEM_CLOCK_120M_PLL_25M_HXTAL       (uint32_t)(120000000)
//#define __SYSTEM_CLOCK_168M_PLL_IRC16M          (uint32_t)(168000000)
#define __SYSTEM_CLOCK_168M_PLL_8M_HXTAL        (uint32_t)(168000000)
//#define __SYSTEM_CLOCK_168M_PLL_25M_HXTAL       (uint32_t)(168000000)
//#define __SYSTEM_CLOCK_200M_PLL_IRC16M          (uint32_t)(200000000)
//#define __SYSTEM_CLOCK_200M_PLL_8M_HXTAL        (uint32_t)(200000000)
//#define __SYSTEM_CLOCK_200M_PLL_25M_HXTAL         (uint32_t)(200000000)

测试代码:

int main(void)
{
    /* configure systick */
    systick_config();
    
    /* enable the LEDs GPIO clock */
    rcu_periph_clock_enable(RCU_GPIOC);

    /* configure LED1 GPIO port */ 
    gpio_mode_set(GPIOC, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN_9);//GPIOC_9
	gpio_mode_set(GPIOC, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN_8);//GPIOC_9
    gpio_output_options_set(GPIOC, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_9);
	gpio_output_options_set(GPIOC, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_8);
    /* reset LED1 GPIO pin */
    gpio_bit_reset(GPIOC, GPIO_PIN_9);
	 gpio_bit_set(GPIOC, GPIO_PIN_8);

    while(1){
        /* turn on LED1 */
        gpio_bit_set(GPIOC, GPIO_PIN_9);
			gpio_bit_reset(GPIOC, GPIO_PIN_8);
        delay_1ms(100);

        /* turn off LED1 */
        gpio_bit_reset(GPIOC, GPIO_PIN_9);
			 gpio_bit_set(GPIOC, GPIO_PIN_8);
        delay_1ms(100);
    }
}

以上GPIO8和GPIO9将产生100ms的方波.