Ucos-II+ucGUI390+ARM2410+LCD＋触摸屏基本整合成功(更新于2007-3-15)

 

 

ucos-II+ucGUI390+ARM9s3c2410+LCD ＋触摸屏基本整合成功

(最近更新于2007-3-15)

 

环境： ads2.2 ＋ ARM9 ＋ s3c2410

 

注意：由于编译器（ ads1.2 或 2.2 ）对全局变量初始化为 0 的不完全支持，有时必须手动初始化为 0 ，切记！！！

 

一、     ucos-II 移植到 ARM9s3c2410

可从官网下载移植代码，基本无需改动。

在os_cpu_a.s中的函数UCOS_IRQHandler中的bl OSIntEnter和bl C_IRQHandler之间插入如下代码（ 见邵贝贝，第 2 版，第 104 页的说明： L3.18(4) ）：

        ldr r0, =OSIntNesting

        ldrb r0,[r0]

        cmp r0,#1

        bne XX

        ldr r0,=OSTCBCur

        ldr r1,[r0]

        str sp,[r1]                 ; store sp in preempted tasks's TCB       

             

XX 

 

二、     ucGui390 移植到 ARM9s3c2410 ：

1. Lcd 驱动：

1） 画点函数：

对dm2410实验板上的lcd，左上为原点（0，0），函数如下：

void LCD2410_SetPixel(int xp, int yp, U16 color, int dindex)

{

       *(pLCDBuffer565 + SCREEN_WIDTH*yp + xp) = color; 

}

为了达到更快的显示速度，别忘了开启Cache ！！！

2）LCD控制器的初始化，对2410函数如下：

int LCD2410_Init(void)

{

       if(!isLcdInit)

       {

              InitLcdPort();

              InitLcdRegs();             

              isLcdInit = 1;

              return 0;

       }

       return 1;

}

 

void InitLcdPort(void)

{

 

    // LCD port initialize.

    s2410IOP->GPCUP = 0xFFFFFFFF;

    s2410IOP->GPCCON = 0xAAAAAAAA;

    s2410IOP->GPDUP = 0xFFFFFFFF;

    s2410IOP->GPDCON = 0xAAAAAAAA;

    s2410IOP->GPGCON &= ~(3 << 8);                 /* Set LCD_PWREN as output                          */

    s2410IOP->GPGCON |= (1 << 8);

    s2410IOP->GPGDAT |= (1 << 4);                 //* Backlight ON   

}

void InitLcdRegs(void)

{

       s2410LCD->LCDCON1   =   (CLKVAL_TFT << 8) |   //* VCLK = HCLK / ((CLKVAL + 1) * 2) -> About 7 Mhz 

                            (EACH_FRAME << 7) |   //* 0 : Each Frame                                  

                            (3           << 5) |   // TFT LCD Pannel                                  

                            (12          << 1) |   //Y: // 16bpp Mode                                     

                            (0           << 0) ;   // Disable LCD Output                            

    s2410LCD->LCDCON2   =   (VBPD        << 24) |   //* VBPD          : ((32-1)&0xff) = 0x1f                            

                            (LINEVAL_TFT << 14) |   //* LINEVAL_TFT : 480 - 1                          

                            (VFPD        << 6) |   //* VFPD          : ((11-1)&0xff) = 0xa                           

                            (VSPW        << 0) ;   //* VSPW          : ((2-1) &0x3f) = 0x1                          

    s2410LCD->LCDCON3   =   (HBPD        << 19) |   //* HBPD          : ((88-1)&0x7f)                             

                            (HOZVAL_TFT << 8) |   //* HOZVAL_TFT    : 800 - 1                         

                            (HFPD        << 0) ;   //* HFPD          : ((40-1)&0xff)                             

    s2410LCD->LCDCON4    =   (MVAL        << 8) |   //* MVAL          : 13                             

                            (HSPW        << 0) ;   //* HSPW          : ((128-1)&0xff)                             

    s2410LCD->LCDCON5   =   (0           << 12) |   // BPP24BL       : LSB valid                       

                            (1           << 11) |   // FRM565 MODE   : 5:5:5:1 Format                    

                            (0           << 10) |   // INVVCLK       : VCLK Falling Edge               

                            (1           << 9) |   // INVVLINE      : Inverted Polarity               

                            (1           << 8) |   // INVVFRAME     : Inverted Polarity               

                            (0           << 7) |   // INVVD         : Normal                          

                            (0           << 6) |   // INVVDEN       : Normal                           

                            (0           << 5) |   // INVPWREN      : Normal                         

                            (0           << 4) |   // INVENDLINE    : Normal                          

                            (1           << 3) |   // PWREN         : Disable PWREN                   

                            (0           << 2) |   // ENLEND        : Disable LEND signal             

                            (0           << 1) |   // BSWP          : Swap Disable                    

                            (1           << 0) ;   // HWSWP         : Swap Enable