VLAN配置实验

拓扑图如下

首先配置交换机SW1，代码如下

[SW1]vlan 2
[SW1-vlan2]q
[SW1]vlan 3
[SW1-vlan3]int g 0/0/3
[SW1-GigabitEthernet0/0/3]port link-type access
[SW1-GigabitEthernet0/0/3]port default vlan 2

[SW1-GigabitEthernet0/0/3]int g 0/0/4
[SW1-GigabitEthernet0/0/4]port link-type access
[SW1-GigabitEthernet0/0/4]port default vlan 3

[SW1-GigabitEthernet0/0/4]int g 0/0/2
[SW1-GigabitEthernet0/0/2]port link-type trunk 
[SW1-GigabitEthernet0/0/2]port trunk allow-pass vlan all

[SW1-GigabitEthernet0/0/2]int g 0/0/1
[SW1-GigabitEthernet0/0/1]port link-type trunk
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all

交换机SW11每个端口的配置结果如下

配置交换机SW2，代码如下

[SW2]vlan 2
[SW2-vlan2]q
[SW2]vlan 3
[SW2-vlan3]q
[SW2]int g 0/0/2
[SW2-GigabitEthernet0/0/2]port link-type access
[SW2-GigabitEthernet0/0/2]port default vlan 2

[SW2-GigabitEthernet0/0/2]int g 0/0/1
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all

[SW2-GigabitEthernet0/0/1]int g 0/0/3
[SW2-GigabitEthernet0/0/3]port link-type access
[SW2-GigabitEthernet0/0/3]port default vlan 3

交换机SW2每个端口的配置结果如下

配置路由器，代码如下

[R1]int g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]dot1q  termination vid  2
[R1-GigabitEthernet0/0/0.1]arp broadcast  enable 
[R1-GigabitEthernet0/0/0.1]ip add 192.168.1.1 25


[R1-GigabitEthernet0/0/0.1]int g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]dot1q termination vid 3
[R1-GigabitEthernet0/0/0.2]arp broadcast enable
[R1-GigabitEthernet0/0/0.2]ip add 192.168.1.129 25

[R1]dhcp enable 
[R1]ip pool 1
Info: It's successful to create an IP address pool.
[R1-ip-pool-1]network 192.168.1.0 mask 25	
[R1-ip-pool-1]gateway-list  192.168.1.1	
[R1-ip-pool-1]dns-list 8.8.8.8 114.114.114.114

[R1-ip-pool-1]ip pool 2
Info: It's successful to create an IP address pool.
[R1-ip-pool-2]network 192.168.1.128 mask 25
[R1-ip-pool-2]gateway-list 192.168.1.129
[R1-ip-pool-2]dns-list 8.8.8.8 114.114.114.114
[R1-ip-pool-2]q

[R1]int g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]dhcp select global
[R1-GigabitEthernet0/0/0.1]int g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]dhcp select global

路由器R1地址池配置情况如下

路由器R1虚拟端口配置情况如下

最后为所有PC端启动DHCP服务，使用PC1pingPC4,实验结果如下