本文稿原创,未经许可授权,不得转载!!!!
机器买回来还是很兴奋的。。。
查资料,看说明,学技术。。。。终于!从廋变成胖的了。。。。兴奋!
买了二个,一个胖一个廋,两全了,接入AC,配置,一开始不成功,之后成功了。。。。。兴奋!!
这会的信息有点爆棚,有点高了,不知所以了。。。。想各种骚操作试试 V7变回V5试试,直接变胖FAT,刷。。。兴奋!!!
刷得还是很爽,挺兴奋的!!!!!
先是SDRAM and RUN ,成功了。。。。重启。。。。。成功!!!爽!!!
【wa4320h-acn】DIR
..........................................................
什么也没有!!!????.............
预感不好。。。。。。。
没办法, reboot.....不行,。。。。。。没有文件(后来才知道是flash:没有了)
reset ctrl+B.............. tftp 刷 wa4300h.ipe 更新main APP 。。。。。无法写入!!! 天呐!!!!不爽。。。黑线!!!
再SDRAM and RUN 不允许(之前在命令CLI中干了傻事,password-recover enable。。。。。)
CTRL+F格式化。。。。。。(出现问题。。。见下图。。。。)查store 没有东西,没有容量。。。。。不见了!!!!!
无语了。。。。。
之前还可以进系统,可能有希望。。。。现在运行不了。。。。
咋整???!!!!!!!!!!!
救命啊!!!!!
各种爬文爬贴。。。。找固件。。。。看能不能刷IK(爱快。。。集客)资料太少,心急啊。。。。没心情细看。。。。。
各种乱试。。。。。。无果!!!!!
————————————————————————————————————————————————
下午累了,早晨中午没吃饭啊。。。。。。老婆孩子回家了,煮了面,出去购物!!!GO!GO!GO!!!(换个心情,休息一下吧。。。。太累了。。。。)送孩子上兴趣班。。。。。
回家,接着干。。。。。。
换思路。。。。。。。。。。。。。。。。。。。。搞定。。。。。。。。。哈哈。。。。(卖个关子,大家看后面吧。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
————————————————————————————————————————————————
因部分操作内容后面的缓存冲掉了,没有之前出问题的操作部分(以后骚操作一定要把步骤给保留好,不能没步骤就乱上,一急就全忘!!!!!)。。。。问题部分只有借用其他贴子的(含图)。。。。请见谅。。。。。
借鉴了一些 WA4320H fit转fat后,flash无法被正确识别 的思路
找了很久想找固件没找到,刷也刷 不进去。
先前的思路:
1、可能是刷错版本,找版本。。。。心情一度差,都要C币,或是其他注册。。。。。而且不一定能解决问题
2、找ROM固件,找了全网没找到,能力有限,精力有限。。。其他就一天左右的时间。。。
先前wa4320h-fit 刷了wa4300h_fat.bin的包成功了。。。
之后wa4320h-fit 升级bootware成功(AC下自动升级的)
现在——
结果出现了这个问题,一直卡在后面,没办法下去了,请问这个该怎么解决啊?试着长摁RST也不行。
明显格式化操作中间少了一步。
还有恢复的可能,将这个AP先灌入V7 AP 的IPE版本,恢复到V7 FIT重新操作。
然后按照
参考如下案例:
https://zhiliao.h3c.com/Theme/details/5036
https://zhiliao.h3c.com/Theme/details/6184
如果是无AC方案的 中间存在格式化操作 一定不能做错
-------------------------------------------------------------------
经过一个晚上的摸索,终于解决了该问题。该问题的产生主要是因为V5和V7文件系统混乱造成的。1.使用编程器写入原fit模式下的编程器bootware固件,4M,必须是comware V7,可以从其他机器备份下来,也可以用fit然后用空填满4m。必须使用编程器,因为用bootware写入无效,bootware已经很混乱了。写入芯片为板载的25芯片,4M的。必须焊下来进行备份或写入,因为编程器的电源会使ap的cpu启动导致无法读取。编程器选用ch341或者minpro100均可以,不要买xtw100,驱动会有安装签名问题,比较麻烦,虽然在win10中也可以使用。
2.写入后再次启动时候,用micro USB转usb线直接连电脑,用超级终端会发现bootware启动后,版本已经变成7.多的。此时ctrl+b中断启动,ctrl+f格式化会发现可以格式化了,而且flash的文件系统回来了,也能够识别了。
3.后期再将fit转fat时候可以参考这篇。https://zhiliao.h3c.com/Theme/details/24566
唯一需要注意的是fit转fat,在将V7降级到V5时候,更新bootware前需要格式化flash,在更新bootware后同样需要格式化flash
最后更新好固件的时候,进入web管理端时候,查看文件是否已经写入到flash中,如果没有写入,必须把文件上传并且改为w4300_fat.bin,并设置为主文件。
————————————————————————————————————————————————————————————————————————
_____________________________________________________________________________________________________
下面进入正题》》》》》》》
_____________________________________________________________________________________________________
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :wa4300_fat.bin
:wa4300h.ipe
Target File Name :wa4300_fat.bin
:wa4300h.ipe
Server IP Address :169.254.55.218 192.168.1.1
Local IP Address :169.254.55.216 192.168.1.2
Subnet Mask :255.255.0.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 2
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
———————————————————————————————————————————————————————
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 1
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 3
Loading.....................................................................
............................................................................
............................................................................
..........................................................Done.
14169088 bytes downloaded!
Something wrong with the file.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 4
Password recovery capability is disabled. To perform this operation, first
enable the password recovery capability using the password-recovery enable
command in CLI.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 4
===============================<File CONTROL>=============