[Docs] [txt|pdf|xml|html] [Tracker] [Email] [Diff1] [Diff2] [Nits] [IPR]
Versions: 00 01 02 03 draft-alvestrand-rmcat-congestion
Network Working Group H. Lundin
Internet-Draft S. Holmer
Intended status: Informational H. Alvestrand, Ed.
Expires: October 27, 2012 Google
April 25, 2012
A Google Congestion Control Algorithm for Real-Time Communication on the
World Wide Web
draft-alvestrand-rtcweb-congestion-02
Abstract
This document describes two methods of congestion control when using
real-time communications on the World Wide Web (RTCWEB); one sender-
based and one receiver-based.
It is published to aid the discussion on mandatory-to-implement flow
control for RTCWEB applications; initial discussion is expected in
the RTCWEB WG's mailing list.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 27, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
Lundin, et al. Expires October 27, 2012 [Page 1]
Internet-Draft Congestion Control for RTCWEB April 2012
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Mathemathical notation conventions . . . . . . . . . . . . 3
2. System model . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Receiver side control . . . . . . . . . . . . . . . . . . . . 5
3.1. Arrival-time model . . . . . . . . . . . . . . . . . . . . 5
3.2. Arrival-time filter . . . . . . . . . . . . . . . . . . . 6
3.3. Over-use detector . . . . . . . . . . . . . . . . . . . . 8
3.4. Rate control . . . . . . . . . . . . . . . . . . . . . . . 8
4. Sender side control . . . . . . . . . . . . . . . . . . . . . 11
5. Interoperability Considerations . . . . . . . . . . . . . . . 12
6. Implementation Experience . . . . . . . . . . . . . . . . . . 13
7. Further Work . . . . . . . . . . . . . . . . . . . . . . . . . 13
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
9. Security Considerations . . . . . . . . . . . . . . . . . . . 14
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 15
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11.1. Normative References . . . . . . . . . . . . . . . . . . . 15
11.2. Informative References . . . . . . . . . . . . . . . . . . 15
Appendix A. Change log . . . . . . . . . . . . . . . . . . . . . 16
A.1. Version -00 to -01 . . . . . . . . . . . . . . . . . . . . 16
A.2. Version -01 to -02 . . . . . . . . . . . . . . . . . . . . 16
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16
Lundin, et al. Expires October 27, 2012 [Page 2]
Internet-Draft Congestion Control for RTCWEB April 2012
1. Introduction
Congestion control is a requirement for all applications that wish to
share the Internet [RFC2914].
The problem of doing congestion control for real-time media is made
difficult for a number of reasons:
o The media is usually encoded in forms that cannot be quickly
changed to accommodate varying bandwidth, and bandwidth
requirements can often be changed only in discrete, rather large
steps媒体通常以无法快速编码的形式编码更改以适应变化的带宽,并且带宽 需求通常只能在离散且相当大的情况下更改脚步
o The participants may have certain specific wishes on how to
respond - which may not be reducing the bandwidth required by the
flow on which congestion is discovered参与者可能对如何 响应-可能不会减少发现拥塞的流量
o The encodings are usually sensitive to packet loss, while the real
time requirement precludes the repair of packet loss by
retransmission编码通常对丢包敏感,而实际时间要求排除了通过 重传
This memo describes two congestion control algorithms that together
are seen to give reasonable performance and reasonable (not perfect)
bandwidth sharing with other conferences and with TCP-using
applications that share the same links.本备忘录描述了两种拥塞控制算法
被认为可以提供合理的性能和合理的(不完美)
与其他会议和使用TCP共享带宽
共享相同链接的应用程序。
The signalling used consists of standard RTP timestamps [RFC3550]
possibly augmented with RTP transmission time offsets [RFC5450],
standard RTCP feedback reports and Temporary Maximum Media Stream Bit
Rate Requests (TMMBR) as defined in [RFC5104] section 3.5.4, or by
using the REMB feedback report defined in [I-D.alvestrand-rmcat-remb]
1.1. Mathemathical notation conventions
The mathematics of this document have been transcribed from a more
formula-friendly format.
The following notational conventions are used:
X_bar The variable X, where X is a vector - conventionally marked by
a bar on top of the variable name.
X_hat An estimate of the true value of variable X - conventionally
marked by a circumflex accent on top of the variable name.
Lundin, et al. Expires October 27, 2012 [Page 3]
Internet-Draft Congestion Control for RTCWEB April 2012
X(i) The "i"th value of X - conventionally marked by a subscript i.
[x y z] A row vector consisting of elements x, y and z.
X_bar^T The transpose of vector X_bar.
E{X} The expected value of the stochastic variable X
2. System model
The following elements are in the system:
o RTP packet - an RTP packet containing media data.
o Frame - a set of RTP packets transmitted from the sender at the
same time instant. This could be a video frame, an audio frame,
or a mix of audio and video packets. A frame can be defined by
the RTP packet send time (RTP timestamp + transmission time
offset), or by the RTP timestamp if the transmission time offset
field is not present.
o Incoming media streams - a stream of frames consisting of RTP
packets.
o Media codec - has a bandwidth control, and encodes the incoming
media stream into an RTP stream.
o RTP sender - sends the RTP stream over the network to the RTP
receiver. Generates the RTP timestamp.
o RTP receiver - receives the RTP stream, notes the time of arrival.
Regenerates the media stream for the recipient.
o RTCP sender at RTP sender - sends sender reports.
o RTCP sender at RTP receiver - sends receiver reports and TMMBR/
REMB messages.
o RTCP receiver at RTP sender - receives receiver reports and TMMBR/
REMB messages, reports these to sender side control.
o RTCP receiver at RTP receiver.
o Sender side control - takes loss rate info, round trip time info,
and TMMBR/REMB messages and computes a sending bitrate.
Lundin, et al. Expires October 27, 2012 [Page 4]
Internet-Draft Congestion Control for RTCWEB April 2012
o Receiver side control - takes the packet arrival info at the RTP
receiver and decides when to send TMMBR/REMB messages.
Together, sender side control and receiver side control implement the
congestion control algorithm.
3. Receiver side control
The receive-side algorithm can be further decomposed into three
parts: an arrival-time filter, an over-use detector, and a remote
rate-control.
3.1. Arrival-time model
This section describes an adaptive filter that continuously updates
estimates of network parameters based on the timing of the received
frames.
At the receiving side we are observing groups of incoming packets,
where each group of packets corresponding to the same frame having
timestamp T(i).
Each frame is assigned a receive time t(i), which corresponds to the
time at which the whole frame has been received (ignoring any packet
losses). A frame is delayed relative to its predecessor if t(i)-t(i-
1)>T(i)-T(i-1), i.e., if the arrival time difference is larger than
the timestamp difference.
We define the (relative) inter-arrival time, d(i) as
d(i) = t(i)-t(i-1)-(T(i)-T(i-1))
Since the time ts to send a frame of size L over a path with a
capacity of C is roughly
ts = L/C
we can model the inter-arrival time as
L(i)-L(i-1)
d(i) = -------------- + w(i) = dL(i)/C+w(i)
C
Here, w(i) is a sample from a stochastic process W, which is a
Lundin, et al. Expires October 27, 2012 [Page 5]
Internet-Draft Congestion Control for RTCWEB April 2012
function of the capacity C, the current cross traffic X(i), and the
current send bit rate R(i). We model W as a white Gaussian process.
If we are over-using the channel we expect w(i) to increase, and if a
queue on the network path is being emptied, w(i) will decrease;
otherwise the mean of w(i) will be zero.
其中,d(i)两帧数据的网络传输时间差,dL(i)两帧数据的大小差, c为网络传输能力, w(i)是我们关注的重点, 它主要由三个因素决定:发送速率, 网络路由能力, 以及网络传输能力。w(i)符合高斯分布, 有如下结论:当w(i)增加是,占用过多带宽(over-using);当w(i)减少时,占用较少带宽(under-using);为0时,用到恰好的带宽。所以,只要我们能计算出w(i),即能判断目前的网络使用情况,从而增加或减少发送的速率。
Breaking out the mean m(i) from w(i) to make the process zero mean,
we get
Equation 5
d(i) = dL(i)/C + m(i) + v(i)
This is our fundamental model, where we take into account that a
large frame needs more time to traverse the link than a small frame,
thus arriving with higher relative delay. The noise term represents
network jitter and other delay effects not captured by the model.
When graphing the values for d(i) versus dL(i) on a scatterplot, we
find that most samples cluster around the center, and the outliers
are clustered along a line with average slope 1/C and zero offset.
其中,dL(i)两帧数据的大小差, c为网络传输能力,m(i)为网络抖动(可能大于0:比之前的网络延迟增大;也可以小于0:比之前的网络延迟减小),v(i)为测量误差
For instance, when using a regular video codec, most frames are
roughly the same size after encoding (the central "cloud"); the
exceptions are I-frames (or key frames) which are typically much
larger than the average causing positive outliers (the I-frame
itself) and negative outliers (the frame after an I-frame) on the dL
axis. Audio frames on the other hand often consist of single packets
of equal size, and an audio-only media stream would have its frames
scattered at dL = 0.
例如,当使用常规视频编解码器时,大多数帧在编码后大小大致相同(中央“云”); I帧(或关键帧)除外,它们通常比平均值大得多,从而在dL轴上导致正离群值(I帧本身)和负离群值(I帧之后的帧)。 另一方面,音频帧通常由大小相等的单个数据包组成,纯音频媒体流的帧分散在dL = 0。
3.2. Arrival-time filter
The parameters d(i) and dL(i) are readily available for each frame i
> 1, and we want to estimate C(i) and m(i) and use those estimates to
detect whether or not we are over-using the bandwidth currently
available. These parameters are easily estimated by any adaptive
filter - we are using the Kalman filter.
Let
theta_bar(i) = [1/C(i) m(i)]^T
and call it the state of time i. We model the state evolution from
time i to time i+1 as
Lundin, et al. Expires October 27, 2012 [Page 6]
Internet-Draft Congestion Control for RTCWEB April 2012
theta_bar(i+1) = theta_bar(i) + u_bar(i)
where u_bar(i) is the zero mean white Gaussian process noise with
covariance
Equation 7
Q(i) = E{u_bar(i) u_bar(i)^T}
Given equation 5 we get
Equation 8
d(i) = h_bar(i)^T theta_bar(i) + v(i)
h_bar(i) = [dL(i) 1]^T
where v(i) is zero mean white Gaussian measurement noise with
variance var_v = sigma(v,i)^2
The Kalman filter recursively updates our estimate
theta_hat(i) = [1/C_hat(i) m_hat(i)]^T
as
z(i) = d(i) - h_bar(i)^T * theta_hat(i-1)
theta_hat(i) = theta_hat(i-1) + z(i) * k_bar(i)
E(i-1) * h_bar(i)
k_bar(i) = --------------------------------------------
var_v_hat + h_bar(i)^T * E(i-1) * h_bar(i)
E(i) = (I - K_bar(i) * h_bar(i)^T) * E(i-1) + Q(i)
I is the 2-by-2 identity matrix.
The variance var_v = sigma(v,i)^2 is estimated using an exponential
averaging filter, modified for variable sampling rate
var_v_hat = beta*sigma(v,i-1)^2 + (1-beta)*z(i)^2
beta = (1-alpha)^(30/(1000 * f_max))
Lundin, et al. Expires October 27, 2012 [Page 7]
Internet-Draft Congestion Control for RTCWEB April 2012
where f_max = max {1/(T(j) - T(j-1))} for j in i-K+1...i is the
highest rate at which frames have been captured by the camera the
last K frames and alpha is a filter coefficient typically chosen as a
number in the interval [0.1, 0.001]. Since our assumption that v(i)
should be zero mean WGN is less accurate in some cases, we have
introduced an additional outlier filter around the updates of
var_v_hat. If z(i) > 3 var_v_hat the filter is updated with 3
sqrt(var_v_hat) rather than z(i). For instance v(i) will not be
white in situations where packets are sent at a higher rate than the
channel capacity, in which case they will be queued behind each
other. In a similar way, Q(i) is chosen as a diagonal matrix with
main diagonal elements given by
diag(Q(i)) = 30/(1000 * f_max)[10^-10 10^-2]^T
It is necessary to scale these filter parameters with the frame rate
to make the detector respond as quickly at low frame rates as at high
frame rates.
3.3. Over-use detector
The offset estimate m(i) is compared with a threshold gamma_1. An
estimate above the threshold is considered as an indication of over-
use. Such an indication is not enough for the detector to signal
over-use to the rate control subsystem. Not until over-use has been
detected for at least gamma_2 milliseconds and at least gamma_3
frames, a definitive确定的 over-use will be signaled. However, if the
offset estimate m(i) was decreased in the last update, over-use will
not be signaled even if all the above conditions are met. Similarly,
the opposite state, under-use, is detected when m(i) < -gamma_1. If
neither over-use nor under-use is detected, the detector will be in
the normal state.
3.4. Rate control
The rate control at the receiving side is designed to increase the
receive-side estimate of the available bandwidth A_hat as long as the
detected state is normal. Doing that assures that we, sooner or
later, will reach the available bandwidth of the channel and detect
an over-use.
As soon as over-use has been detected the receive-side estimate of
the available bandwidth is decreased. In this way we get a recursive
and adaptive estimate of the available bandwidth.一旦检测到过度使用,接收方估算可用带宽减少。 这样我们得到一个递归以及可用带宽的自适应估计。
In this document we make the assumption that the rate control
subsystem is executed periodically and that this period is constant.在本文档中,我们假设速率控制子系统定期执行,并且该时间段是恒定的。
Lundin, et al. Expires October 27, 2012 [Page 8]
Internet-Draft Congestion Control for RTCWEB April 2012
The rate control subsystem has 3 states: Increase, Decrease and Hold.
"Increase" is the state when no congestion拥塞 is detected; "Decrease" is
the state where congestion is detected, and "Hold" is a state that
waits until built-up queues have drained before going to "increase"
state.
The state transitions (with blank fields meaning "remain in state")
are:
State ----> | Hold |Increase |Decrease
Signal-----------------------------------------
v | | |
Over-use | Decrease |Decrease |
-----------------------------------------------
Normal | Increase | |Hold
-----------------------------------------------
Under-use | |Hold |Hold
-----------------------------------------------
The subsystem starts in the increase state, where it will stay until
over-use or under-use has been detected by the detector subsystem.
On every update the receive-side estimate of the available bandwidth
is increased with a factor which is a function of the global system
response time and the estimated measurement noise variance var_v_hat.
The global system response time is the time from an increase that
causes over-use until that over-use can be detected by the over-use
detector. The variance var_v_hat affects how responsive the Kalman
filter is, and is thus used as an indicator of the delay inflicted by
the Kalman filter.子系统以增加状态启动,它将一直保持到检测器子系统检测到过度使用或使用不足为止。 在每次更新时,可用带宽的接收侧估计值都会增加一个因数,该因数是全局系统响应时间和估计的测量噪声方差var_v_hat的函数。 全局系统响应时间是指从引起过度使用的增加到过度使用检测器可以检测到过度使用的时间。 方差var_v_hat影响卡尔曼滤波器的响应度,因此用作卡尔曼滤波器造成的延迟的指标。
A_hat(i) = eta*A_hat(i-1)
1.001+B
eta(RTT, var_v_hat) = ------------------------------------------
1+e^(b(d*RTT - (c1 * var_v_hat + c2)))
Here, B, b, d, c1 and c2 are design parameters.
Since the system depends on over-using the channel to verify the
current available bandwidth estimate, we must make sure that our
estimate doesn't diverge from the rate at which the sender is
actually sending. Thus, if the sender is unable to produce a bit
stream with the bit rate the receiver is asking for, the available
bandwidth estimate must stay within a given bound. Therefore we
introduce a threshold
Lundin, et al. Expires October 27, 2012 [Page 9]
Internet-Draft Congestion Control for RTCWEB April 2012
A_hat(i) < 1.5 * R_hat(i)
where R_hat(i) is the incoming bit rate measured over a T seconds
window:
R_hat(i) = 1/T * sum(L(j)) for j from 1 to N(i)
N(i) is the number of frames received the past T seconds and L(j) is
the payload size of frame j.
When an over-use is detected the system transitions to the decrease
state, where the receive-side available bandwidth estimate is
decreased to a factor times the currently incoming bit rate.
A_hat(i) = alpha*R_hat(i)
alpha is typically chosen to be in the interval [0.8, 0.95].
When the detector signals under-use to the rate control subsystem, we
know that queues in the network path are being emptied, indicating
that our available bandwidth estimate is lower than the actual
available bandwidth. Upon that signal the rate control subsystem
will enter the hold state, where the receive-side available bandwidth
estimate will be held constant while waiting for the queues to
stabilize at a lower level - a way of keeping the delay as low as
possible. This decrease of delay is wanted, and expected,
immediately after the estimate has been reduced due to over-use, but
can also happen if the cross traffic over some links is reduced. In
either case we want to measure the highest incoming rate during the
under-use interval:
R_max = max{R_hat(i)} for i in 1..K
where K is the number of frames of under-use before returning to the
normal state. R_max is a measure of the actual bandwidth available
and is a good guess of what bit rate the sender should be able to
transmit at. Therefore the receive-side available bandwidth estimate
will be set to R_max when we transition from the hold state to the
increase state.
One design decision is when to send rate control messages. The time
from a change in congestion to the sending of the feedback message is
a limitation on how fast the sender can react. Sending too many
messages giving no new information is a waste of bandwidth - but in
the case of severe congestion, feedback messages can be lost,
resulting in a failure to react in a timely manner.
Lundin, et al. Expires October 27, 2012 [Page 10]
Internet-Draft Congestion Control for RTCWEB April 2012
The conclusion is that feedback messages should be sent on a
"heartbeat" schedule, allowing the sender side control to react to
missing feedback messages by reducing its send rate, but they should
also be sent whenever the estimated bandwidth value has changed
significantly, without waiting for the heartbeat time, up to some
limiting upper bound on the send rate.
The minimum interval is named t_min_fb_interval.
The maximum interval is named t_max_fb_interval.
The permissible values of these intervals will be bounded by the RTP
session's RTCP bandwidth and its rtcp_frr setting.
[TODO: Get some example values for these timers]
4. Sender side control
An additional congestion controller resides at the sending side. It
bases its decisions on the round-trip time, packet loss and available
bandwidth estimates transmitted from the receiving side.
The available bandwidth estimates produced by the receiving side are
only reliable when the size of the queues along the channel are large
enough. If the queues are very short, over-use will only be visible
through packet losses, which aren't used by the receiving side
algorithm.
This algorithm is run every time a receive report arrives at the
sender, which will happen no more often than t_min_fb_interval, and
no less often than t_max_fb_interval. If no receive report is
received within 2x t_max_fb_interval (indicating at least 2 lost
feedback reports), the algorithm will take action as if all packets
in the interval have been lost, resulting in a halving of the send
rate.
o If 2-10% of the packets have been lost since the previous report
from the receiver, the sender available bandwidth estimate As(i)
(As denotes 'sender available bandwidth') will be kept unchanged.
o If more than 10% of the packets have been lost a new estimate is
calculated as As(i)=As(i-1)(1-0.5p), where p is the loss ratio.
o As long as less than 2% of the packets have been lost As(i) will
be increased as As(i)=1.05(As(i-1)+1000)
The new send-side estimate is limited by the TCP Friendly Rate
Lundin, et al. Expires October 27, 2012 [Page 11]
Internet-Draft Congestion Control for RTCWEB April 2012
Control formula [RFC3448] and the receive-side estimate of the
available bandwidth A(i):
8 s
As(i) >= ----------------------------------------------------------
R*sqrt(2*b*p/3) + (t_RTO*(3*sqrt(3*b*p/8) * p * (1+32*p^2)))
As(i) <= A(i)
where b is the number of packets acknowledged by a single TCP
acknowledgement (set to 1 per TFRC recommendations), t_RTO is the TCP
retransmission timeout value in seconds (set to 4*R) and s is the
average packet size in bytes. R is the round-trip time in seconds.
(The multiplication by 8 comes because TFRC is computing bandwidth in
bytes, while this document computes bandwidth in bits.)
In words: The sender-side estimate will never be larger than the
receiver-side estimate, and will never be lower than the estimate
from the TFRC formula.
We motivate the packet loss thresholds by noting that if the
transmission channel has a small amount of packet loss due to over-
use, that amount will soon increase if the sender does not adjust his
bit rate. Therefore we will soon enough reach above the 10 %
threshold and adjust As(i). However if the packet loss rate does not
increase, the losses are probably not related to self-induced channel
over-use and therefore we should not react on them.
5. Interoperability Considerations
There are three scenarios of interest, and one included for reference
o Both parties implement the algorithms described here
o Sender implements the algorithm described in section Section 4,
recipient does not implement Section 3
o Recipient implements the algorithm in section Section 3, sender
does not implement Section 4.
In the case where both parties implement the algorithms, we expect to
see most of the congestion control response to slowly varying
conditions happen by TMMBR/REMB messages from recipient to sender.
At most times, the sender will send less than the congestion-inducing
bandwidth limit C, and when he sends more, congestion will be
detected before packets are lost.
Lundin, et al. Expires October 27, 2012 [Page 12]
Internet-Draft Congestion Control for RTCWEB April 2012
If sudden changes happen, packets will be lost, and the sender side
control will trigger, limiting traffic until the congestion becomes
low enough that the system switches back to the receiver-controlled
state.
In the case where sender only implements, we expect to see somewhat
higher loss rates and delays, but the system will still be overall
TCP friendly and self-adjusting; the governing term in the
calculation will be the TFRC formula.
In the case where recipient implements this algorithm and sender does
not, congestion will be avoided for slow changes as long as the
sender understands and obeys TMMBR/REMB; there will be no backoff for
packet-loss-inducing changes in capacity. Given that some kind of
congestion control is mandatory for the sender according to the TMMBR
spec, this case has to be reevaluated against the specific congestion
control implemented by the sender.
6. Implementation Experience
This algorithm has been implemented in the open-source WebRTC
project.
7. Further Work
This draft is offered as input to the congestion control discussion.
Work that can be done on this basis includes:
o Consideration of timing info: It may be sensible to use the
proposed TFRC RTP header extensions [I-D.gharai-avtcore-rtp-tfrc]
to carry per-packet timing information, which would both give more
data points and a timestamp applied closer to the network
interface. This draft includes consideration of using the
transmission time offset defined in [RFC5450]
o Considerations of cross-channel calculation: If all packets in
multiple streams follow the same path over the network, congestion
or queueing information should be considered across all packets
between two parties, not just per media stream. A feedback
message (REMB) that may be suitable for such a purpose is given in
o Considerations of cross-channel balancing: The decision to slow
down sending in a situation with multiple media streams should be
taken across all media streams, not per stream.
Lundin, et al. Expires October 27, 2012 [Page 13]
Internet-Draft Congestion Control for RTCWEB April 2012
o Considerations of additional input: How and where packet loss
detected at the recipient can be added to the algorithm.
o Considerations of locus of control: Whether the sender or the
recipient is in the best position to figure out which media
streams it makes sense to slow down, and therefore whether one
should use TMMBR to slow down one channel, signal an overall
bandwidth change and let the sender make the decision, or signal
the (possibly processed) delay info and let the sender run the
algorithm.
o Considerations of over-bandwidth estimation: Whether we can use
the estimate of how much we're over bandwidth in section 3 to
influence how much we reduce the bandwidth, rather than using a
fixed factor.
o Startup considerations. It's unreasonable to assume that just
starting at full rate is always the best strategy.
o Dealing with sender traffic shaping, which delays sending of
packets. Using send-time timestamps rather than RTP timestamps
may be useful here, but as long as the sender's traffic shaping
does not spread out packets more than the bottleneck link, it
should not matter.
o Stability considerations. It is not clear how to show that the
algorithm cannot provide an oscillating state, either alone or
when competing with other algorithms / flows.
These are matters for further work; since some of them involve
extensions that have not yet been standardized, this could take some
time.
8. IANA Considerations
This document makes no request of IANA.
Note to RFC Editor: this section may be removed on publication as an
RFC.
9. Security Considerations
An attacker with the ability to insert or remove messages on the
connection will, of course, have the ability to mess up rate control,
causing people to send either too fast or too slow, and causing
congestion.
Lundin, et al. Expires October 27, 2012 [Page 14]
Internet-Draft Congestion Control for RTCWEB April 2012
In this case, the control information is carried inside RTP, and can
be protected against modification or message insertion using SRTP,
just as for the media. Given that timestamps are carried in the RTP
header, which is not encrypted, this is not protected against
disclosure, but it seems hard to mount an attack based on timing
information only.
10. Acknowledgements
Thanks to Randell Jesup, Magnus Westerlund, Varun Singh, Tim Panton,
Soo-Hyun Choo, Jim Gettys, Ingemar Johansson, Michael Welzl and
others for providing valuable feedback on earlier versions of this
draft.
11. References
11.1. Normative References
Alvestrand, H., "RTCP message for Receiver Estimated
Maximum Bitrate", draft-alvestrand-rmcat-remb-00 (work in
progress), January 2012.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3448] Handley, M., Floyd, S., Padhye, J., and J. Widmer, "TCP
Friendly Rate Control (TFRC): Protocol Specification",
RFC 3448, January 2003.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, July 2003.
[RFC5104] Wenger, S., Chandra, U., Westerlund, M., and B. Burman,
"Codec Control Messages in the RTP Audio-Visual Profile
with Feedback (AVPF)", RFC 5104, February 2008.
[RFC5450] Singer, D. and H. Desineni, "Transmission Time Offsets in
RTP Streams", RFC 5450, March 2009.
11.2. Informative References
Gharai, L. and C. Perkins, "RTP with TCP Friendly Rate
Control", draft-gharai-avtcore-rtp-tfrc-01 (work in
Lundin, et al. Expires October 27, 2012 [Page 15]
Internet-Draft Congestion Control for RTCWEB April 2012
progress), September 2011.
[RFC2914] Floyd, S., "Congestion Control Principles", BCP 41,
RFC 2914, September 2000.
Appendix A. Change log
A.1. Version -00 to -01
o Added change log
o Added appendix outlining new extensions
o Added a section on when to send feedback to the end of section 3.3
"Rate control", and defined min/max FB intervals.
o Added size of over-bandwidth estimate usage to "further work"
section.
o Added startup considerations to "further work" section.
o Added sender-delay considerations to "further work" section.
o Filled in acknowledgements section from mailing list discussion.
A.2. Version -01 to -02
o Defined the term "frame", incorporating the transmission time
offset into its definition, and removed references to "video
frame".
o Referred to "m(i)" from the text to make the derivation clearer.
o Made it clearer that we modify our estimates of available
bandwidth, and not the true available bandwidth.
o Removed the appendixes outlining new extensions, added pointers to
REMB draft and RFC 5450.
Lundin, et al. Expires October 27, 2012 [Page 16]
Internet-Draft Congestion Control for RTCWEB April 2012
Authors' Addresses
Henrik Lundin
Kungsbron 2
Stockholm 11122
Sweden
Stefan Holmer
Kungsbron 2
Stockholm 11122
Sweden
Email: holmer@google.com
Harald Alvestrand (editor)
Kungsbron 2
Stockholm 11122
Sweden
Email: harald@alvestrand.no
Lundin, et al. Expires October 27, 2012 [Page 17]
Html markup produced by rfcmarkup 1.129d, available from https://tools.ietf.org/tools/rfcmarkup/