通过X-modem方式刷CISCO交换机IOS

首先需要有IOS文件,如果没有备份原文件的话,可以找个同一版本的IOS来替代。

第一种方法:X-Modem

以前我曾经尝试过一种方法,就是当Flash被删除后,启动无法进入系统,可以用X-Modem来恢复它。当时我不小心删除了一台Cisco2950交换机的Flash IOS,导致系统无法启动,在查过不少资料后得到一个结论:唯一的方法通过X-Modem来恢复。我的恢复方法如下:

1、用控制线连接交换机console口与计算机串口1,用带有xmodem功能的终端软件连接(win2000 and xp的超级终端就带这功能)。

2、设置连接方式为串口1(如果连接的是其他串口就选择其他串口),速率9600,无校验,无流控,停止位1。或者点击默认设置也可以。

3、连接以后计算机回车出现交换机无ios的界面,一般的提示符是:switch:

4、拔掉交换机后的电源线重新启动交换机

5、在超级终端输入:
switch:flash_init
会出现如下提示:
Initializing Flash...

6:输入拷贝指令:

switch:copy xmodem: flash:image_filename.bin

出现如下提示:

Begin the Xmodem or Xmodem-1K transfer now...

7、系统提示不断出现C这个字母就可以开始传文件了

8、点击超级终端菜单:传送---发送文件,在协议选项中选择Xmodem或者Xmodem-1K协议,然后选择ios的影像文件(*.bin),开始传送。

9、因为不能改速率,所以传送得很慢,我的大概传送了80分钟左右,请耐心等待。

10、传送完毕后提示:
File "xmodem:" successfully copied to ....
switch:

11、在提示符下输入

switch:boot

启用新的ios系统

12、重新加电完成恢复工作。


这个是我恢复的方法,现在看来非常的不科学,效率低。后来看了别人同样用X-Modem恢复IOS,但是效率要高的方法:

先打开超级终端,进入rommon 模式(Ctrl+Break组合键),键入confreg, 如下:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rommon 1 > confreg 回车

Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600

do you wish to change the configuration? y/n [n]: y (选择 yes)
enable "diagnostic mode"? y/n [n]: n (选择 no)
enable "use net in IP bcast address"? y/n [n]: n (选择 no)
disable "load rom after netboot fails"? y/n [n]: n (选择 no)
enable "use all zero broadcast"? y/n [n]: n (选择 no)
enable "break/abort has effect"? y/n [n]: n (选择 no)
enable "ignore system config info"? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [0]: 7 (选择 7,用最大的115200速率的xmodem传输)
change the boot characteristics? y/n [n]: n (选择 no)

Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by the boot system commands
or default to: cisco2-C2600

do you wish to change the configuration? y/n [n]: n (选择 no)

You must reset or power cycle for new config to take effect

rommon 2 > reset 回车

注意:在此时键入 reset键之前,开始定义串口速度(我的电脑---端口属性----串口速度调为115200),然后再修改超级终端里设置速率为115200,记住,一定这么做!否则出现乱码! 然后关闭这个超级终端,重新建立一个超级终端连接,(期间系统重新启动)启动后,出现

rommon 1> 提示符
然后,输入
rommon 1> xmodem -r

Do not start the sending program yet...

Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y (选择 yes)
Ready to receive file ...

此时,在超级终端的菜单上的“传送”---“发送文件”----选择IOS镜像文件所在地以及选择使用“xmodem”协议,点击“发送”即可

然后等待10-20分钟左右就把3-6M的IOS灌进去了!

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(修改回计算机串口与超级终端、路由器confreg下的xmodem等9600的传输速率)

(videre注:实际用的时候,我发现这个命令总是改不成功,后来发现在line con 0下面有了一个speed 115200,所以即使改register成功,启动以后router又执行speed 115200,还是不行,所以如果有这个问题,记得把这个语句no掉)

Router>en 进入新IOS的特权模式

Router#reload 重启系统

Proceed with reload? [confirm] 回车

00:01:04: %SYS-5-RELOAD: Reload requested
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
PC = 0xfff0a530, Vector = 0x500, SP = 0x680127b0
C2600 platform with 24576 Kbytes of main memory

PC = 0xfff0a530, Vector = 0x500, SP = 0x80004684

monitor: command "boot" aborted due to user interrupt

rommon 1 > confreg ( 输入“confreg”命令)

Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by the boot system commands
or default to: cisco2-C2600

do you wish to change the configuration? y/n [n]: y (选择 yes)
enable "diagnostic mode"? y/n [n]: n (选择 no)
enable "use net in IP bcast address"? y/n [n]: n (选择 no)
disable "load rom after netboot fails"? y/n [n]: n (选择 no)
enable "use all zero broadcast"? y/n [n]: n (选择 no)
enable "break/abort has effect"? y/n [n]: n (选择 no)
enable "ignore system config info"? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [7]: 0 (选择 0,改回用标准速率速率9600的xmodem传输)
change the boot characteristics? y/n [n]: n (选择 no)

Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600

do you wish to change the configuration? y/n [n]: n

You must reset or power cycle for new config to take effect
rommon 2 >

此时手工改回计算机串口与超级终端2者传输速率为9600

然后敲入
rommon 2 >reset
( 最好关电源)

他的方法有两个地方和我的不一样,首先是他在启动后进入了rommon模式,其次是他修改了串口的速率,这样就比我快的多了。
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值