基于STM32的智能门禁系统(指纹、蓝牙、刷卡、OLED、电机)

目录

一、主要功能

二、硬件资源

三、程序编程

四、实现现象

---

一、主要功能

基于STM32单片机，六个按键，分别代表指纹、蓝牙、刷卡的正确进门与错误进门；
比如第一个按键按下，表示指纹正确，OLED显示指纹正确，开门，
第二个按键按下的话，则指纹错误，OLED显示指纹错误，请重试，
第二个按键连续按三次以上，则OLED显示开门失败，此时启动报警系统，
即蜂鸣器报警。同理，蓝牙与刷卡的操作同样如此。

二、硬件资源

基于KEIL5编写C++代码，PROTEUS8.15进行仿真，全部资源在页尾，提供安装包。

三、程序编程

#include "main.h"
#include "gpio.h"
#include "./HAL/key/key.h"
#include "./HAL/OLED/OLED_NEW.H"


void Key_function(void);								//按键函数
void Display_function(void); //显示函数
void Manage_function(void);							//处理函数

#define LED(a) (a?HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_RESET):HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET)) 

#define BEEP(a) (a?HAL_GPIO_WritePin(BEEP_GPIO_Port, BEEP_Pin, GPIO_PIN_RESET):HAL_GPIO_WritePin(BEEP_GPIO_Port, BEEP_Pin, GPIO_PIN_SET)) 


uint8_t key_num,flag_display;         //按键与显示变量
static int flag=0;



uint8_t flag_led,flag_beep;						//灯、报警标志位
uint16_t time_num;
static int flag1=0;

void SystemClock_Config(void);

/****
*******按键设置函数
*****/
void Key_function(void)
{
	key_num = Chiclet_Keyboard_Scan();	//按键扫描
	if(key_num != 0)										//有按键按下
	{
		switch(key_num)
		{
			case 1:flag=1;break;
			case 2:flag=3;break;
			case 3:flag=5;break;
			case 4:flag=2;flag1++;break;
			case 5:flag=4;flag1++;break;
			case 6:flag=6;flag1++;break;
		}
	
	}
}


/****
*******显示函数
*****/
void Display_function(void)
{
	switch(flag)
	{
		case 1:
			Oled_ShowCHinese(0,0,"指纹正确");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请开门");
		break;
			case 2:
			Oled_ShowCHinese(0,0,"指纹错误");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请重试");
		break;
			case 3:
			Oled_ShowCHinese(0,0,"蓝牙正确");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请开门");
		break;
			case 4:
			Oled_ShowCHinese(0,0,"蓝牙错误");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请重试");
		break;
			case 5:
			Oled_ShowCHinese(0,0,"刷卡正确");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请开门");
		break;
			case 6:
			Oled_ShowCHinese(0,0,"刷卡错误");
			Oled_ShowString(64,0,",");
		  Oled_ShowCHinese(80,0,"请重试");
		break;
	}


}


/****
*******处理函数
*****/
void Manage_function(void)
{
	if(flag1 == 3)
	{
		flag_beep=1;
		flag_led=1;
		Oled_ShowCHinese(0,2,"开门失败");
		Oled_ShowCHinese(0,4,"报警");
	}
	else
		{
		flag_beep=0;
		flag_led=0;
	}

  if(flag_beep==1)
    BEEP(1);
  else
    BEEP(0);
  if(flag_led==1)
    LED(1);
  else
    LED(0);
}




int main(void)
{
  HAL_Init();
  SystemClock_Config();
  MX_GPIO_Init();
  OLED_Init();									//OLED初始化
  OLED_Clear();									//OLED清屏
  while (1)
  {
    Key_function();							//按键函数
		Display_function();					//显示函数
		Manage_function();					//处理函数
  }

}


void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};


  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL4;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }


  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
  {
    Error_Handler();
  }
  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
  PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV2;
  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
  {
    Error_Handler();
  }
}

/* USER CODE BEGIN 4 */
/* USER CODE END 4 */

/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */
void Error_Handler(void)
{
  /* USER CODE BEGIN Error_Handler_Debug */
  /* User can add his own implementation to report the HAL error return state */
  __disable_irq();
  while (1)
  {
  }
  /* USER CODE END Error_Handler_Debug */
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

四、实现现象

具体动态效果看B站演示视频：

基于STM32的智能门禁系统(指纹、蓝牙、刷卡、OLED、电机)

全部资料（源程序、仿真文件、安装包、演示视频）：

链接：https://pan.baidu.com/s/1B3YvL6RwC3TdHNIVC0yLSw?pwd=xl3o 
提取码：xl3o