svn配置

svn配置路径配置

注意，在配置过程中，一般需要先用admin(管理员用户先进行配置进入后创建多个文件夹分别对应如：php, android … 授权对应的路径)，这样才能在后续配置路径中可用。如果不是， 就会在checkout中出现如下错误:

URL 'svn://xxx.xx.xxx.xxx:xxxx/php/' doesn't exist

代码块[文件夹/conf/authz] (授权配置)

admin=test
android=test2   
php=test3

[/]
@admin=rw  //读写 管理员权限
[/php]     //php php用户群权限 注意:必须先用admin用户创建总文件夹下的php目录才能成功checkout
@php=rw
[/android]  //安卓用户群权限  注意:必须先用admin用户创建总文件夹下的android目录才能成功checkout
@android=rw

代码块[文件夹/conf/passwd] (用户名密码配置)

test=123456
test2=123456
test3=123456

代码块[文件夹/conf/svnserve] (svn服务配置)

### This file controls the configuration of the svnserve daemon, if you
### use it to allow access to this repository.  (If you only allow
### access through http: and/or file: URLs, then this file is
### irrelevant.)

### Visit http://subversion.tigris.org/ for more information.

[general]
### These options control access to the repository for unauthenticated
### and authenticated users.  Valid values are "write", "read",
### and "none".  The sample settings below are the defaults.
anon-access = none           //这里将###去掉表示启用代码, 注意如果想复制这一块请将所有'//'后的注释删除
auth-access = write          //这里将###去掉
### The password-db option controls the location of the password
### database file.  Unless you specify a path starting with a /,
### the file's location is relative to the directory containing
### this configuration file.
### If SASL is enabled (see below), this file will NOT be used.
### Uncomment the line below to use the default password file.
password-db = passwd          //这里将###去掉
### The authz-db option controls the location of the authorization
### rules for path-based access control.  Unless you specify a path
### starting with a /, the file's location is relative to the the
### directory containing this file.  If you don't specify an
### authz-db, no path-based access control is done.
### Uncomment the line below to use the default authorization file.
authz-db = authz                //这里将###去掉
### This option specifies the authentication realm of the repository.
### If two repositories have the same authentication realm, they should
### have the same password database, and vice versa.  The default realm
### is repository's uuid.
realm = My First Repository Test 

[sasl]
### This option specifies whether you want to use the Cyrus SASL
### library for authentication. Default is false.
### This section will be ignored if svnserve is not built with Cyrus
### SASL support; to check, run 'svnserve --version' and look for a line
### reading 'Cyrus SASL authentication is available.'
# use-sasl = true
### These options specify the desired strength of the security layer
### that you want SASL to provide. 0 means no encryption, 1 means
### integrity-checking only, values larger than 1 are correlated
### to the effective key length for encryption (e.g. 128 means 128-bit
### encryption). The values below are the defaults.
# min-encryption = 0
# max-encryption = 256

启用svn

$ svnserve -d -r [接文件夹路径] -listen-port [端口] 

svn输出 svncheckout

url: svn://xxx.xx.xxx.xxx:xxxx/php/  //即可获取php文件夹下的所有内容
url: svn://xxx.xx.xxx.xxx:xxxx/android/  //即可获取android文件夹下的所有内容