S5PV210：支持NAND启动u-boot

1、修改：u-boot\board\samsung\smdkv210\smdkv210.c中的copy_bl2_to _ram函数，增加对SD/NAND启动的判断

void copy_bl2_to_ram(void)
{
/*
** ch:  通道
** sb:  起始块
** bs:  块大小
** dst: 目的地
** i: 	是否初始化
*/
#define CopySDMMCtoMem(ch, sb, bs, dst, i) \
	(((u8(*)(int, u32, unsigned short, u32*, u8))\
	(*((u32 *)0xD0037F98)))(ch, sb, bs, dst, i))
	
#define MP0_1CON  (*(volatile u32 *)0xE02002E0)
#define	MP0_3CON  (*(volatile u32 *)0xE0200320)
#define	MP0_6CON  (*(volatile u32 *)0xE0200380)	

#define NF8_ReadPage_Adv(a,b,c) (((int(*)(u32, u32, u8*))(*((u32 *)0xD0037F90)))(a,b,c))
	
	u32 bl2Size = 250 * 1024;	// 250K
	
	u32 OM = *(volatile u32 *)(0xE0000004);	// OM Register
	OM &= 0x1F;					// 取低5位
	
	if (OM == 0x2)				// NAND 2 KB, 5cycle 8-bit ECC
	{
		u32 cfg = 0;
		struct s5pv210_nand *nand_reg = (struct s5pv210_nand *)(struct s5pv210_nand *)samsung_get_base_nand();
		
		/* initialize hardware */
		/* HCLK_PSYS=133MHz(7.5ns) */
		cfg =	(0x1 << 23) |	/* Disable 1-bit and 4-bit ECC */
				/* 下面3个时间参数稍微比计算出的值大些（我这里依次加1），否则读写不稳定 */
				(0x3 << 12) |	/* 7.5ns * 2 > 12ns tALS tCLS */
				(0x2 << 8) | 	/* (1+1) * 7.5ns > 12ns (tWP) */
				(0x1 << 4) | 	/* (0+1) * 7.5 > 5ns (tCLH/tALH) */
				(0x0 << 3) | 	/* SLC NAND Flash */
				(0x0 << 2) |	/* 2KBytes/Page */
				(0x1 << 1);		/* 5 address cycle */
	
		writel(cfg, &nand_reg->nfconf);
		
		writel((0x1 << 1) | (0x1 << 0), &nand_reg->nfcont);
		/* Disable chip select and Enable NAND Flash Controller */
	
		/* Config GPIO */
		MP0_1CON &= ~(0xFFFF << 8);
		MP0_1CON |= (0x3333 << 8);
		MP0_3CON = 0x22222222;
		MP0_6CON = 0x22222222;		
		
		int i = 0;
		int pages = bl2Size / 2048;		// 多少页
		int offset = 0x4000 / 2048;			// u-boot.bin在NAND中的偏移地址(页地址)
		u8 *p = (u8 *)CONFIG_SYS_SDRAM_BASE;
		for (; i < pages; i++, p += 2048, offset += 1)
			NF8_ReadPage_Adv(offset / 64, offset % 64, p);
	}
	else if (OM == 0xC)		// SD/MMC
	{
		u32 V210_SDMMC_BASE = *(volatile u32 *)(0xD0037488);	// V210_SDMMC_BASE
		u8 ch = 0;
		
		/* 参考S5PV210手册7.9.1 SD/MMC REGISTER MAP */
		if (V210_SDMMC_BASE == 0xEB000000)		// 通道0
			ch = 0;
		else if (V210_SDMMC_BASE == 0xEB200000)	// 通道2
			ch = 2;
		CopySDMMCtoMem(ch, 32, bl2Size / 512, (u32 *)CONFIG_SYS_SDRAM_BASE, 0);
	}
}

重新编译，烧写到SD卡启动，在通过TFTP烧写到NAND

A、

SMDKV210 # tftpboot 20000000 smdkv210-spl.bin
smc911x: detected LAN9220 controller
smc911x: phy initialized
smc911x: MAC 1a:2a:3a:4a:5a:6a
Using smc911x-0 device
TFTP from server 192.168.1.101; our IP address is 192.168.1.108
Filename 'smdkv210-spl.bin'.
Load address: 0x20000000
Loading: T #
         0 Bytes/s
done
Bytes transferred = 1420 (58c hex)

B、

SMDKV210 # nand write 20000000 0 $filesize

NAND write: device 0 offset 0x0, size 0x58c
 1420 bytes written: OK

C、

SMDKV210 # tftpboot 20000000 u-boot.bin
smc911x: detected LAN9220 controller
smc911x: phy initialized
smc911x: MAC 1a:2a:3a:4a:5a:6a
Using smc911x-0 device
TFTP from server 192.168.1.101; our IP address is 192.168.1.108
Filename 'u-boot.bin'.
Load address: 0x20000000
Loading: T ################
         40 KiB/s
done
Bytes transferred = 231368 (387c8 hex)

D、

SMDKV210 # nand write 20000000 4000  $filesize

NAND write: device 0 offset 0x4000, size 0x387c8
 231368 bytes written: OK

最后执行：saveenv  把环境变量都保存到NAND中！（就能消除环境参数错误）