静态综合实验-HCIP第一次作业

一：实验拓扑

二：实验需求

1 R6为isp,接口IP地址均为公有有地址；该设备只能配置IP地址, 之后不能再对其进行任何配置;

2 R1—R5为局域网,私有P地址192.168.1.6/24,请合理分配;
3 R1,R2,R4,各有两个环回地址; R5,R6各有一个环回地址;所有路由器上环回均代表连接用户的接口;
4 R3下的两台PC通过DHCP自动获取IP地址;
5选路最佳,路由表尽量小,避免环路;
6 R1—R5均可以访问R6的环回;
7 R6 telnet R5的公有IP地址时,实际登陆到R1上;
8 R4与R5正常通过1000M链路,故障时通过100M链路;

三：实验步骤

R1：

[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]ip ad 192.168.1.1 30 
[r1-GigabitEthernet0/0/0]int g 0/0/1
[r1-GigabitEthernet0/0/1]ip ad 192.168.1.5 30
[r1-GigabitEthernet0/0/1]int l0
[r1-LoopBack0]ip ad 192.168.1.33 28
[r1-LoopBack0]int l1
[r1-LoopBack1]ip ad 192.168.1.49 28
  
[r1]ip route-static 0.0.0.0 0 192.168.1.2
[r1]ip route-static 0.0.0.0 0 192.168.1.6
[r1]ip route-static 192.168.1.64 27 192.168.1.2
[r1]ip route-static 192.168.1.8 30 192.168.1.2
[r1]ip route-static 192.168.1.12 30 192.168.1.6
[r1]ip route-static 192.168.1.128 28 192.168.1.6
  
[r1]ip route-static 192.168.1.32 27 NULL 0
 

[r1]aaa    
[r1-aaa]local-user aaa privilege level 15 password cipher 12345
Info: Add a new user.
[r1-aaa]local-user aaa service-type telnet
[r1-aaa]q
[r1]user-interface vty 0 4
[r1-ui-vty0-4]au    
[r1-ui-vty0-4]authentication-mode aaa

R2:

[r2]int g 0/0/0
[r2-GigabitEthernet0/0/0]ip ad 192.168.1.2 30
[r2-GigabitEthernet0/0/0]int g 0/0/1
[r2-GigabitEthernet0/0/1]ip add 192.168.1.9 30 
[r2-GigabitEthernet0/0/1]int l0
[r2-LoopBack0]ip ad 192.168.1.65 28
[r2-LoopBack0]int l1
[r2-LoopBack1]ip ad 192.168.1.81 28
  
[r2]ip route-static 0.0.0.0 0 192.168.1.10
[r2]ip route-static 192.168.1.128 28 192.168.1.10
[r2]ip route-static 192.168.1.128 28 192.168.1.1
[r2]ip route-static 192.168.1.4 30 192.168.1.1
[r2]ip route-static 192.168.1.32 27 192.168.1.1
 
 
[r2]ip route-static 192.168.1.64 27 NULL 0

R3:

[r3]int g 0/0/0
[r3-GigabitEthernet0/0/0]ip ad 192.168.1.6 30
[r3-GigabitEthernet0/0/0]int g 0/0/1
[r3-GigabitEthernet0/0/1]ip add 192.168.1.13 30 
[r3-GigabitEthernet0/0/1]int l0
[r3-LoopBack0]ip ad 192.168.1.97 27

  
[r3]ip route-static 0.0.0.0 0 192.168.1.14
[r3]ip route-static 192.168.1.64 27 192.168.1.14
[r3]ip route-static 192.168.1.64 27 192.168.1.5
[r3]ip route-static 192.168.1.0 30 192.168.1.5
[r3]ip route-static 192.168.1.32 27 192.168.1.5
 
 [r3]ip route-static 192.168.1.64 27 NULL 0

[r3]dhcp enable
[r3]ip pool aa
Info: It's successful to create an IP address pool.
[r3-ip-pool-aa]network 192.168.1.128 mask 28
[r3-ip-pool-aa]gateway-list 192.168.1.129
[r3-ip-pool-aa]dns-list 8.8.8.8

R4

[r4]int g 0/0/0
[r4-GigabitEthernet0/0/0]ip ad 192.168.1.14 30 
[r4-GigabitEthernet0/0/0]int g 0/0/1
[r4-GigabitEthernet0/0/1]ip ad 192.168.1.10 30
[r4-GigabitEthernet0/0/1]
[r4-GigabitEthernet0/0/1]int g 0/0/2
[r4-GigabitEthernet0/0/2]ip ad 192.168.1.21 30
[r4-GigabitEthernet0/0/2] 
[r4-GigabitEthernet0/0/2]int g 4/0/0
[r4-GigabitEthernet4/0/0]ip ad 192.168.1.21 30
[r4-GigabitEthernet4/0/0]
[r4-GigabitEthernet4/0/0]int l0
[r4-LoopBack0]ip ad 192.168.1.129 28
[r4-LoopBack0]int l1
[r4-LoopBack1]ip ad 192.168.1.145 28
 
 
[r4]ip route-static 0.0.0.0 0 192.168.1.9
[r4]ip route-static 0.0.0.0 0 192.168.1.22 preference 70
[r4]ip route-static 192.168.1.32 27 192.168.1.9

[r4]ip route-static 192.168.1.32 27 192.168.1.13

[r4]ip route-static 192.168.1.0 30 192.168.1.9
[r4]ip route-static 192.168.1.64 27 192.168.1.9
[r4]ip route-static 192.168.1.96 27 192.168.1.13
[r4]ip route-static 192.168.1.4 30 192.168.1.13

[r4]ip route-static 192.168.1.128 27 NULL 0

[r4]ip route-static 192.168.1.160 27 192.168.1.18

[r4]ip route-static 192.168.1.0 24 NULL 0

[r4]ip route-static 0.0.0.0 0 GigabitEthernet 2/0/0 192.168.1.18

R5:

[r5]int g 0/0/0
[r5-GigabitEthernet0/0/0]ip ad 192.168.1.18 30
[r5-GigabitEthernet0/0/0]int g 0/0/1
[r5-GigabitEthernet0/0/1]ip ad 12.0.0.1 24
[r5-GigabitEthernet0/0/1]int g 0/0/2
[r5-GigabitEthernet0/0/2]ip ad 192.168.1.22 30
[r5-GigabitEthernet0/0/2]
[r5-GigabitEthernet0/0/2]int l0
[r5-LoopBack0]ip ad 192.168.1.161 27
 
[r5]ip route-static 0.0.0.0 0 12.0.0.2
[r5]ip route-static 192.168.1.0 24 192.168.1.17
[r5]ip route-static 192.168.1.0 24 192.168.1.21 pre    
[r5]ip route-static 192.168.1.0 24 192.168.1.21 preference 70
 
[r5]acl 2000   
[r5-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[r5-acl-basic-2000]q
[r5]int g 0/0/1    
[r5-GigabitEthernet0/0/1]nat outbound 2000
[r5-GigabitEthernet0/0/1]q
 
 
[r5]int g 0/0/1   
[r5-GigabitEthernet0/0/1]nat s    
[r5-GigabitEthernet0/0/1]nat server p    
[r5-GigabitEthernet0/0/1]nat server protocol tcp g    
[r5-GigabitEthernet0/0/1]nat server protocol tcp global c    
[r5-GigabitEthernet0/0/1]nat server protocol tcp global current-interface 23 in    
 
[r5-GigabitEthernet0/0/1]nat server protocol tcp global current-interface 23 ins
ide 192.168.1.1 23
Warning:The port 23 is well-known port. If you continue it may cause function fa
ilure.
Are you sure to continue?[Y/N]:y
[r5-GigabitEthernet0/0/1]