ensp交换机中使用链路聚合实现不同网段通信

实现环境

三台核心交换机，两台pc

拓扑图

解释：在不同pc机中使用链路聚合实现在不同的网段中通信（全网通信），我是配置好之后写的日志

1：修改LSW1、LSW2和LSW3名称

<LSW1>sys
Enter system view, return user view with Ctrl+Z.
[LSW1]sys LSW1

<LSW2>sys
Enter system view, return user view with Ctrl+Z.
[LSW2]sys LSW2

<LSW3>sys
Enter system view, return user view with Ctrl+Z.
[LSW3]sys LSW3

1.2配置好pc1和pc2

2配置 LLDP协议使能，LLDP协议：查看互相设备链路及接口状态

LSW1

[LSW1]lldp enable
Info: Global LLDP is already enabled.

LSW2

[LSW2]lldp enable
Info: Global LLDP is already enabled.

LSW3

[LSW3]lldp enable
Info: Global LLDP is already enabled.

查看连接状态

[LSW1]display lldp neighbor brief 
Local Intf   Neighbor Dev             Neighbor Intf             Exptime
GE0/0/1      LSW2                     GE0/0/1                   108    
GE0/0/2      LSW2                     GE0/0/2                   108    
GE0/0/3      LSW2                     GE0/0/3                   108    
GE0/0/4      LSW3                     GE0/0/1                   110    
GE0/0/5      LSW3                     GE0/0/2                   110    
GE0/0/6      LSW3                     GE0/0/3                   110  

2.1配置链路聚合组，看接口 就知道连接的是那一台交换机

LSW1

#创建链路聚合组

[LSW1]interface Eth-Trunk 1

#使用llcp协议协商链路聚合接口及链路
[LSW1-Eth-Trunk1]mode lacp-static 

#在链路聚合是否添加其他成员
[LSW1-Eth-Trunk1]trunkport g 0/0/1 0/0/2 0/0/3

[LSW1]interface Eth-Trunk 2
[LSW1-Eth-Trunk1]mode lacp-static 
[LSW1-Eth-Trunk1]trunkport g 0/0/4 0/0/5 0/0/6

LSW2

[LSW2]display lldp neighbor brief 

[LSW2]interface Eth-Trunk 1
[LSW2-Eth-Trunk1]mode lacp-static 
[LSW2-Eth-Trunk1]trunkport g 0/0/1 0/0/2 0/0/3

[LSW2]interface Eth-Trunk 2
[LSW2-Eth-Trunk1]mode lacp-static 
[LSW2-Eth-Trunk1]trunkport g 0/0/4 0/0/5 0/0/6

LSW3

[LSW3]display lldp neighbor brief 

[LSW3]interface Eth-Trunk 1
[LSW3-Eth-Trunk1]mode lacp-static 
[LSW3-Eth-Trunk1]trunkport g 0/0/1 0/0/2 0/0/3

[LSW3]interface Eth-Trunk 2
[LSW3-Eth-Trunk1]mode lacp-static 
[LSW3-Eth-Trunk1]trunkport g 0/0/4 0/0/5 0/0/6

3配置好vlanif 10 to 30,vlanif 100,vlanif 200

链路聚合组是把三条线变成一条线，vlanif相当于access口

LSW1

#创建好vlan10和30

[LSW1]vlan batch 10 30

#进入到vlanif 10

[LSW1]interface vlanif 10 

#配置ip地址
[LSW1-Vlanif10]ip address 10.1.34.2 24

#进入链路聚合组1

[LSW1]interface Eth-Trunk 1  

#接口设置为trunk
[LSW1-Eth-Trunk1]port link-type trunk 

#放行所有vlan2 to 4094标签
[LSW1-Eth-Trunk1]port trunk allow-pass vlan all

#查看配置情况

[LSW1-Eth-Trunk1]dis this
#
interface Eth-Trunk1
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094
 mode lacp-static
#
return

#

#进入到vlanif 30

[LSW1]interface vlanif 30

#配置ip地址
[LSW1-Vlanif10]ip address 10.1.35.2 24

#进入链路聚合组2

[LSW1]interface Eth-Trunk 2 

#接口设置为trunk
[LSW1-Eth-Trunk2]port link-type trunk 

#放行所有vlan2 to 4094标签
[LSW1-Eth-Trunk1]port trunk allow-pass vlan all

LSW2

[LSW2]vlan batch 10 20 100

[LSW2]interface vlanif 10 
[LSW2-Vlanif10]ip address 10.1.34.1 24

[LSW2]interface Eth-Trunk 1  
[LSW2-Eth-Trunk1]port link-type trunk 
[LSW2-Eth-Trunk1]port trunk allow-pass vlan all

[LSW2]interface vlanif 20
[LSW2-Vlanif10]ip address 10.1.45.1 24

[LSW2]interface Eth-Trunk 2 
[LSW2-Eth-Trunk2]port link-type trunk 
[LSW2-Eth-Trunk1]port trunk allow-pass vlan all

#进入连接到pc1的接口上

[LSW2]int g 0/0/7  

#配置access接口
[LSW2-GigabitEthernet0/0/7]port link-type access 

#配置该接口为vlan 100 标签
[LSW2-GigabitEthernet0/0/7]port default vlan 100 
#查看
[LSW2-GigabitEthernet0/0/7]dis this
#
interface GigabitEthernet0/0/7
 port link-type access
 port default vlan 100
#
return

#配置好vlanif 100

[LSW2]interface vlanif 100

#配置网关
[LSW2-Vlanif100]ip address 192.168.1.254 24

LSW3

[LSW3]vlan batch 20 30

[LSW3]interface vlanif 20 
[LSW3-Vlanif10]ip address 10.1.45.2 24

[LSW3]interface Eth-Trunk 1  
[LSW3-Eth-Trunk1]port link-type trunk 
[LSW3-Eth-Trunk1]port trunk allow-pass vlan all

[LSW3]interface vlanif 30
[LSW3-Vlanif10]ip address 10.1.35.1 24

[LSW3]interface Eth-Trunk 2 
[LSW3-Eth-Trunk2]port link-type trunk 
[LSW3-Eth-Trunk1]port trunk allow-pass vlan all

[LSW3]int g 0/0/7  
[LSW3-GigabitEthernet0/0/7]port link-type access 
[LSW3-GigabitEthernet0/0/7]port default vlan 200

[LSW3]interface vlanif 200
[LSW3-Vlanif200]ip address 192.168.2.254 24

4配置ospf，时交换机能够互通

LSW1

#进入loopback接口，loopback接口：用于实现设备测试网络的连通性

[LSW1]int LoopBack 0
#配置好route-id，掩码为32
[LSW1-LoopBack0]ip add ip address 1.1.1.1 32

#创建ospf进程1 route-id配置为1.1.1.1

[LSW1]ospf 1 router-id 1.1.1.1

#将设备添加到骨干区域中

[LSW1-ospf-1]area 0

#将loopback接口地址宣告区域中

[LSW1-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0

#将直连网段宣告到区域中

[LSW1-ospf-1-area-0.0.0.0]network  10.1.34.0 0.0.0.255

[LSW1-ospf-1-area-0.0.0.0]network  10.1.35.0 0.0.0.2555

#查看配置情况

[LSW1-ospf-1-area-0.0.0.0]dis this
#
 area 0.0.0.0
  network 10.1.34.0 0.0.0.255
  network 1.1.1.1 0.0.0.0
  network 10.1.35.0 0.0.0.255
#
return
 

LSW2

[LSW2]int LoopBack 0
[LSW2-LoopBack0]ip add ip address 2.2.2.2 32

[LSW2]ospf 1 router-id 2.2.2.2

[LSW2-ospf-1]area 0

[LSW2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0

[LSW2-ospf-1-area-0.0.0.0]network  10.1.34.0 0.0.0.255

[LSW2-ospf-1-area-0.0.0.0]network  10.1.45.0 0.0.0.2555

[LSW2-ospf-1-area-0.0.0.0]network  192.168.1.0 0.0.0.2555

[LSW2-ospf-1-area-0.0.0.0]dis this
May 23 2024 20:41:39-08:00 LSW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.2
5.191.3.1 configurations have been changed. The current change number is 42, the
 change loop count is 0, and the maximum number of records is 4095.
#
 area 0.0.0.0
  network 2.2.2.2 0.0.0.0
  network 10.1.34.0 0.0.0.255
  network 10.1.45.0 0.0.0.255
  network 192.168.1.0 0.0.0.255
#
return

LSW3

[LSW3]int LoopBack 0
[LSW3-LoopBack0]ip add ip address 3.3.3.3 32

[LSW3]ospf 1 router-id 3.3.3.3

[LSW3-ospf-1]area 0

[LSW3-ospf-1-area-0.0.0.0]network 3.3.3.3 0.0.0.0

[LSW3-ospf-1-area-0.0.0.0]network  10.1.35.0 0.0.0.255

[LSW3-ospf-1-area-0.0.0.0]network  10.1.45.0 0.0.0.2555

[LSW3-ospf-1-area-0.0.0.0]network  192.168.2.0 0.0.0.2555

[LSW3-ospf-1-area-0.0.0.0]dis this
#
 area 0.0.0.0
  network 3.3.3.3 0.0.0.0
  network 10.1.45.0 0.0.0.255
  network 10.1.35.0 0.0.0.255
  network 192.168.2.0 0.0.0.255
#
return

5全网都能通信

#学习数通的一些经验，与大家共勉