实验要求
一.配置路由器IP
R1
[R1]int LoopBack 0
[R1-LoopBack0]ip add 192.168.1.1 24
[R1-GigabitEthernet0/0/0]ip add 16.0.0.1 24
[R1-GigabitEthernet0/0/1]ip add 116.0.0.1 24
R2
[R2]int LoopBack 0
[R2-LoopBack0]ip add 192.168.2.1 24
[R2-GigabitEthernet0/0/0]ip add 26.0.0.1 24
R3
[R3]int LoopBack 0
[R3-LoopBack0]ip add 192.168.3.1 24
[R3-GigabitEthernet0/0/0]ip add 36.0.0.1 24
R4
[R4]int LoopBack 0
[R4-LoopBack0]ip add 192.168.4.1 24
[R4-GigabitEthernet0/0/0]ip add 46.0.0.1 24
R5
[R5]int LoopBack 0
[R5-LoopBack0]ip add 192.168.5.1 24
[R5-GigabitEthernet0/0/0]ip add 56.0.0.1 24
二. 配置环回地址
[ISP]int LoopBack 0
[ISP-LoopBack0]ip add 6.6.6.6 24
[ISP-GigabitEthernet0/0/1]ip add 116.0.0.2 24
[ISP-GigabitEthernet0/0/0]ip add 16.0.0.2 24
[ISP-GigabitEthernet2/0/0]ip add 26.0.0.2 24
[ISP-GigabitEthernet3/0/0]ip add 36.0.0.2 24
[ISP-GigabitEthernet4/0/0]ip add 46.0.0.2 24
[ISP-GigabitEthernet0/0/2]ip add 56.0.0.2 24
三.配置缺省路由
[R1]ip route-static 0.0.0.0 0 116.0.0.2
[R1]ip route-static 0.0.0.0 0 16.0.0.2
[R2]ip route-static 0.0.0.0 0 26.0.0.2
[R3]ip route-static 0.0.0.0 0 36.0.0.2
[R4]ip route-static 0.0.0.0 0 46.0.0.2
[R5]ip route-static 0.0.0.0 0 56.0.0.2
四.设R1、R4、R5为全连的MGRE
R1
[R1]int Tunnel 0/0/0
[R1-Tunnel0/0/0]ip address 192.168.6.1 24
[R1-Tunnel0/0/0]tunnel-protocol gre p2mp
[R1-Tunnel0/0/0]source 16.0.0.1
[R1-Tunnel0/0/0]nhrp network-id 100
[R1-Tunnel0/0/0]nhrp entry 192.168.6.2 46.0.0.1 register
[R1-Tunnel0/0/0]nhrp entry 192.168.6.3 56.0.0.1 register
R4
[R4]int Tunnel 0/0/0
[R4-Tunnel0/0/0]ip address 192.168.6.2 24
[R4-Tunnel0/0/0]tunnel-protocol gre p2mp
[R4-Tunnel0/0/0]source 46.0.0.1
[R4-Tunnel0/0/0]nhrp network-id 100
[R4-Tunnel0/0/0]nhrp entry 192.168.6.1 16.0.0.1 register
[R4-Tunnel0/0/0]nhrp entry 192.168.6.3 56.0.0.1 register
R5
[R5]int Tunnel 0/0/0
[R5-Tunnel0/0/0]ip address 192.168.6.3 24
[R5-Tunnel0/0/0]tunnel-protocol gre p2mp
[R5-Tunnel0/0/0]source 56.0.0.1
[R5-Tunnel0/0/0]nhrp network-id 100
[R5-Tunnel0/0/0]nhrp entry 192.168.6.1 16.0.0.1 register
[R5-Tunnel0/0/0]nhrp entry 192.168.6.2 46.0.0.1 registe
五.设R1、R2、R3为星型拓扑结构,D1为中心站点
R1
[R1]int Tunnel 0/0/1
[R1-Tunnel0/0/1]ip address 192.168.7.1 24
[R1-Tunnel0/0/1]tunnel-protocol gre p2mp
[R1-Tunnel0/0/1]source 116.0.0.1
[R1-Tunnel0/0/1]nhrp network-id 100
[R1-Tunnel0/0/1]nhrp entry multicast dynamic
R2
[R2]int Tunnel 0/0/1
[R2-Tunnel0/0/1]ip address 192.168.7.2 24
[R2-Tunnel0/0/1]tunnel-protocol gre p2mp
[R2-Tunnel0/0/1]nhrp network-id 100
[R2-Tunnel0/0/1]source GigabitEthernet 0/0/0
[R2-Tunnel0/0/1]nhrp entry 192.168.7.1 116.0.0.1 register
R3
[R3]int Tunnel 0/0/1
[R3-Tunnel0/0/1]ip address 192.168.7.3 24
[R3-Tunnel0/0/1]tunnel-protocol gre p2mp
[R3-Tunnel0/0/1]source GigabitEthernet 0/0/0
[R3-Tunnel0/0/1]nhrp network-id 100
[R3-Tunnel0/0/1]nhrp entry 192.168.7.1 116.0.0.1 register
六.使用ospf配置路由
R1
[R1]ospf 1 router-id 1.1.1.1
[R1-ospf-1]area 0
[R1-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255
R2
[R2]ospf 1 router-id 2.2.2.2
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255
R3
[R3]ospf 1 router-id 3.3.3.3
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 192.168.3.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255
R4
[R4]ospf 1 router-id 4.4.4.4
[R4-ospf-1]area 0
[R4-ospf-1-area-0.0.0.0]network 192.168.4.0 0.0.0.255
[R4-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255
R5
[R5]ospf 1 router-id 5.5.5.5
[R5-ospf-1]area 0
[R5-ospf-1-area-0.0.0.0]network 192.168.5.0 0.0.0.255
[R5-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255
七.更改网络类型
[R1]int t0/0/0
[R1-Tunnel0/0/0]ospf network-type broadcast
[R1-Tunnel0/0/0]int t0/0/1
[R1-Tunnel0/0/1]ospf network-type broadcast
[R2]int t0/0/1
[R2-Tunnel0/0/1]ospf network-type broadcast
[R3-ospf-1]int t0/0/1
[R3-Tunnel0/0/1]ospf network-type broadcast
[R4]int t0/0/0
[R4-Tunnel0/0/0]ospf network-type broadcast
[R5-ospf-1]int t0/0/0
[R5-Tunnel0/0/0]ospf network-type broadcast