MGRE环境下OSPF配置

实验要求

1.R6为ISP只能配置IP地址，R1-R5的环回为私有网段。

2.R1/4/5为全连的MGRE结构，R1/2/3为星型的拓扑结构，R1为中心站点。

3.所有私有网段可以互相通讯，私有网段使用OSPF完成。

实验拓扑

分析

R1-R5设置私有网段环回，R6为ISP路由配置接口ip。

R1R4R5为全连MGRE结构，R1R2R3为星型的拓扑结构，R1为中心站点，R2R3为分支，R1R4R5为全连则互为邻居，所有私有网段可以互相通讯，OSPF配置私有网段

配置

1. R1

[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip address 1.1.0.1 30
[R1-GigabitEthernet0/0/0]int g0/0/1
[R1-GigabitEthernet0/0/1]ip address 1.2.0.1 30

#建立环回
[R1-GigabitEthernet0/0/1]int lo0
[R1-LoopBack0]ip address 192.168.1.1 24

#缺省

[R1]ip route-static 0.0.0.0 0 1.2.0.2 

[R1]ip route-static 0.0.0.0 0 1.1.0.2

#配置隧道

[R1]interface Tunnel 0/0/1
[R1-Tunnel0/0/1]ip address 192.168.7.1 24
[R1-Tunnel0/0/1]tunnel-protocol gre p2mp
[R1-Tunnel0/0/1]source 1.2.0.1
[R1-Tunnel0/0/1]nhrp network-id 101
[R1-Tunnel0/0/1]nhrp entry 192.168.7.2 4.0.0.1 register
[R1-Tunnel0/0/1]nhrp entry 192.168.7.3 5.0.0.1 register
#中心配置

[R1]interface Tunnel 0/0/0
[R1-Tunnel0/0/0]ip address 192.168.6.1 24
[R1-Tunnel0/0/0]tunnel-protocol gre p2mp
[R1-Tunnel0/0/0]nhrp network-id 100
[R1-Tunnel0/0/0]nhrp entry multicast dynamic 
[R1-Tunnel0/0/0]source 1.1.0.1
[R1-Tunnel0/0/0]ospf network-type broadcast 

#ospf

[R1]ospf router-id 1.1.1.1 
[R1-ospf-1]area 0
[R1-ospf-1-area-0.0.0.0]network 192.168.1.0  0.0.0.0
[R1-ospf-1-area-0.0.0.0]network 192.168.6.0  0.0.0.255
[R1-ospf-1-area-0.0.0.0]network 192.168.7.0  0.0.0.255

2. R2

[R2]int g0/0/0 
[R2-GigabitEthernet0/0/0]ip address 2.0.0.1 30
[R2-GigabitEthernet0/0/0]int lo0
[R2-LoopBack0]ip address 192.168.2.1 24

#缺省

[R2]ip route-static 0.0.0.0 0 2.0.0.2

#分支配置

[R2]interface Tunnel 0/0/0
[R2-Tunnel0/0/0]ip address 192.168.6.2 24
[R2-Tunnel0/0/0]tunnel-protocol gre p2mp
[R2-Tunnel0/0/0]source g0/0/0
[R2-Tunnel0/0/0]nhrp network-id 100
[R2-Tunnel0/0/0]nhrp entry 192.168.6.1 1.1.0.1 register

#ospf

[R2]ospf router-id 2.2.2.2
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

3. R3

[R3]int g0/0/0  
[R3-GigabitEthernet0/0/0]ip address 3.0.0.1 30
[R3-GigabitEthernet0/0/0]int lo0
[R3-LoopBack0]ip address 192.168.3.1 24

#缺省

[R3]ip route-static 0.0.0.0 0 3.0.0.2 

#分支配置

[R3]interface Tunnel 0/0/0
[R3-Tunnel0/0/0]ip address 192.168.6.3 24
[R3-Tunnel0/0/0]tunnel-protocol gre p2mp
[R3-Tunnel0/0/0]source g0/0/0
[R3-Tunnel0/0/0]nhrp network-id 100
[R3-Tunnel0/0/0]nhrp entry 192.168.6.1 1.1.0.1 register

#ospf

[R3]ospf router-id 3.3.3.3
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 192.168.3.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

4. R4 

[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip address 4.0.0.1 30
[R4-GigabitEthernet0/0/0]int lo0
[R4-LoopBack0]ip address 192.168.4.1 24

#缺省

[R4]ip route-static 0.0.0.0 0 4.0.0.2

#配置隧道

[R4]interface Tunnel 0/0/1
[R4-Tunnel0/0/1]ip address 192.168.7.2 24
[R4-Tunnel0/0/1]tunnel-protocol gre p2mp
[R4-Tunnel0/0/1]source 4.0.0.1
[R4-Tunnel0/0/1]nhrp network-id 101 
[R4-Tunnel0/0/1]nhrp entry 192.168.7.1 1.2.0.1 register 
[R4-Tunnel0/0/1]nhrp entry 192.168.7.3 5.0.0.1 register

#ospf

[R4]ospf router-id 4.4.4.4
[R4-ospf-1]area 0 
[R4-ospf-1-area-0.0.0.0]network 192.168.4.0 0.0.0.255
[R4-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255

5. R5

[R5]int g0/0/0  
[R5-GigabitEthernet0/0/0]ip address 5.0.0.1 30
[R5-GigabitEthernet0/0/0]int lo0
[R5-LoopBack0]ip address 192.168.5.1 24

缺省

[R5]ip route-static 0.0.0.0 0 5.0.0.2

#配置隧道

[R5]interface Tunnel 0/0/1
[R5-Tunnel0/0/1]ip address 192.168.7.3 24
[R5-Tunnel0/0/1]tunnel-protocol gre p2mp 
[R5-Tunnel0/0/1]nhrp network-id 101
[R5-Tunnel0/0/1]source 5.0.0.1
[R5-Tunnel0/0/1]nhrp entry 192.168.7.1 1.2.0.1 register   
[R5-Tunnel0/0/1]nhrp entry 192.168.7.2 4.0.0.1 register

#ospf

[R5]ospf router-id 5.5.5.5
[R5-ospf-1]area 0  
[R5-ospf-1-area-0.0.0.0]network 192.168.5.0 0.0.0.255
[R5-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255

 6. R6

[ISP]int g0/0/1 
[ISP-GigabitEthernet0/0/1]ip address 1.2.0.2 30
[ISP-GigabitEthernet0/0/1]int g0/0/0
[ISP-GigabitEthernet0/0/0]ip address 1.1.0.2 30
[ISP-GigabitEthernet0/0/0]int g2/0/0
[ISP-GigabitEthernet2/0/0]ip address 2.0.0.2 30
[ISP-GigabitEthernet2/0/0]int g3/0/0
[ISP-GigabitEthernet3/0/0]ip address 3.0.0.2 30
[ISP-GigabitEthernet3/0/0]int g4/0/0
[ISP-GigabitEthernet4/0/0]ip address 4.0.0.2 30
[ISP-GigabitEthernet4/0/0]int g0/0/2
[ISP-GigabitEthernet0/0/2]ip address 5.0.0.2 30

验证

IP配置

 NHRP邻居情况

 ospf配置