keepalived可用来解决haproxy挂掉后集群无法使用的问题
一.高可用集群
1.1 集群类型
·LB：Load Balance 负载均衡 （lvs和haproxy解决的）
LVS/HAProxy/nginx（http/upstream, stream/upstream）
·HA：High Availability 高可用集群
数据库、Redis
·SPoF: Single Point of Failure，解决单点故障
HPC：High Performance Computing 高性能集群 （解决单个主机运算能力达不到要求）
1.2 系统可用性
SLA：Service-Level Agreement 服务等级协议（提供服务的企业与客户之间就服务的品质、水准、性能
等方面所达成的双方共同认可的协议或契约）
A = MTBF / (MTBF+MTTR）（平均故障间隔/（平均故障间隔+修复前平均时间））
99.95%:(60*24*30)*(1-0.9995)=21.6分钟 #一般按一个月停机时间统计指标 ：99.9%, 99.99%, 99.999%,99.9999%
1.3 系统故障
硬件故障：设计缺陷、wear out（损耗）、非人为不可抗拒因素
软件故障：设计缺陷 bug
1.4 实现高可用
提升系统高用性的解决方案：降低MTTR- Mean Time To Repair(平均故障时间)
解决方案：建立冗余机制
·active/passive 主/备
·active/active 双主
·active --> HEARTBEAT（心跳） --> passive （主备）
·active <--> HEARTBEAT <--> active （双主）
1.5.VRRP：Virtual Router Redundancy Protocol （虚拟路由冗余协议）
虚拟路由冗余协议,解决静态网关单点风险
·物理层:路由器、三层交换机
·软件层:keepalived
虚拟路由冗余协议：为了让外部人员访问内部网络
如果主机（201.1.1.1）挂了会自动把ip（201.1.1.3）迁移到另一个主机（201.1.1.2）上面
1.5.1 VRRP 相关术语
·虚拟路由器：Virtual Router
·虚拟路由器标识：VRID(0-255)，唯一标识虚拟路由器
·VIP：Virtual IP
·VMAC：Virutal MAC (00-00-5e-00-01-VRID)
·物理路由器：
master：主设备
backup：备用设备
priority：优先级 （vip最后会到哪里取决于路由器的优先级）
1.5.2 VRRP 相关技术
通告：心跳，优先级等；周期性
工作方式：抢占式，非抢占式 （抢占模式：如果主机挂了ip已经给了别的主机，当该主机好了之后IP还会回来，非抢占式模式不回来）
安全认证：
·无认证
·简单字符认证：预共享密钥 （明文加密）
·MD5 （对称加密）
工作模式：
·主/备：单虚拟路由器
·主/主：主/备（虚拟路由器1），备/主（虚拟路由器2），（两个主机都有业务，互为主备）（两个主机同时挂的可能性很小）
二.Keepalived 部署
2.1 keepalived 简介
vrrp 协议的软件实现，原生设计目的为了高可用 ipvs服务
官网：http://keepalived.org/
功能：
·基于vrrp协议完成地址流动 （来回迁移）
·为vip地址所在的节点生成ipvs规则(在配置文件中预先定义)
·为ipvs集群的各RS做健康状态检测
·基于脚本调用接口完成脚本中定义的功能，进而影响集群事务，以此支持nginx、haproxy等服务
2.2 Keepalived 架构
官方文档：
https://keepalived.org/doc/
http://keepalived.org/documentation.html
·用户空间核心组件：
vrrp stack：VIP消息通告 （心跳）
checkers：监测real server
system call：实现 vrrp 协议状态转换时调用脚本的功能
SMTP：邮件组件 （主机挂了之后除了迁移vip之外，还需要给管理员发送邮件）
IPVS wrapper：生成IPVS规则
Netlink Reflector：网络接口
WatchDog：监控进程
·控制组件：提供keepalived.conf 的解析器，完成Keepalived配置
·IO复用器：针对网络目的而优化的自己的线程抽象
·内存管理组件：为某些通用的内存管理功能（例如分配，重新分配，发布等）提供访问权限
其中控制组件，IO复用器，内存管理组件不需要控制（自动控制的）
2.3 Keepalived 环境准备
#IP环境搭建
#ka1
[root@ka1 ~]# ip ad
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0c:29:73:de:b2 brd ff:ff:ff:ff:ff:ff
inet 172.25.254.10/24 brd 172.25.254.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6 fe80::20c:29ff:fe73:deb2/64 scope link tentative
valid_lft forever preferred_lft forever
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
valid_lft forever preferred_lft forever
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
#ka2
[root@ka2 ~]# ip ad
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0c:29:c2:71:75 brd ff:ff:ff:ff:ff:ff
inet 172.25.254.20/24 brd 172.25.254.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6 fe80::20c:29ff:fec2:7175/64 scope link tentative
valid_lft forever preferred_lft forever
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
valid_lft forever preferred_lft forever
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
#relserver1
[root@relserver1 ~]# ip ad
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0c:29:22:84:f2 brd ff:ff:ff:ff:ff:ff
inet 172.25.254.110/24 brd 172.25.254.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6 fe80::20c:29ff:fe22:84f2/64 scope link tentative
valid_lft forever preferred_lft forever
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
valid_lft forever preferred_lft forever
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
#relserver2
[root@relserver2 ~]# ip ad
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0c:29:27:bb:85 brd ff:ff:ff:ff:ff:ff
inet 172.25.254.120/24 brd 172.25.254.255 scope global noprefixroute eth0
valid_lft forever preferred_lft forever
inet6 fe80::20c:29ff:fe27:bb85/64 scope link tentative
valid_lft forever preferred_lft forever
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
valid_lft forever preferred_lft forever
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000
link/ether 52:54:00:f1:ee:92 brd ff:ff:ff:ff:ff:ff
#安装httpd
[root@relserver1 ~]# yum install httpd -y
[root@relserver1 ~]# echo 172.25.254.110 > /var/www/html/index.html
[root@relserver1 ~]# systemctl enable httpd
[root@relserver1 ~]# systemctl start httpd
[root@relserver1 ~]# systemctl stop firewalld
[root@relserver1 ~]# setenforce 0
setenforce: SELinux is disabled
[root@relserver2 ~]# yum install httpd -y
[root@relserver2 ~]# echo 172.25.254.120 > /var/www/html/index.html
[root@relserver2 ~]# systemctl enable httpd
[root@relserver2 ~]# systemctl start httpd
[root@relserver2 ~]# systemctl stop firewalld
[root@relserver2 ~]# setenforce 0
setenforce: SELinux is disabled#测试
[root@ka1 ~]# curl 172.25.254.110
172.25.254.110
[root@ka1 ~]# curl 172.25.254.120
172.25.254.120·各节点时间必须同步：ntp, chrony
·关闭防火墙及SELinux
·各节点之间可通过主机名互相通信：非必须
·建议使用/etc/hosts文件实现：非必须
·各节点之间的root用户可以基于密钥认证的ssh服务完成互相通信：非必须
2.4 Keepalived 相关文件
·软件包名：keepalived
·主程序文件：/usr/sbin/keepalived
·主配置文件：/etc/keepalived/keepalived.conf
·配置文件示例：/usr/share/doc/keepalived/
·Unit File：/lib/systemd/system/keepalived.service
·Unit File的环境配置文件：/etc/sysconfig/keepalived
RHEL7中可能会遇到一下bug
systemctl restart keepalived #新配置可能无法生效
systemctl stop keepalived;systemctl start keepalived #无法停止进程，需要 kill 停止2.5 Keepalived 安装
安装 keepalived
[root@ka1 ~]# yum install keepalived -y
[root@ka2 ~]# yum install keepalived -y#查看文件
[root@ka1 ~]# rpm -ql keepalived
/etc/keepalived
/etc/keepalived/keepalived.conf
/etc/sysconfig/keepalived
/usr/bin/genhash
/usr/lib/systemd/system/keepalived.service
/usr/libexec/keepalived
/usr/sbin/keepalived
/usr/share/doc/keepalived-1.3.5
/usr/share/doc/keepalived-1.3.5/AUTHOR
/usr/share/doc/keepalived-1.3.5/CONTRIBUTORS
/usr/share/doc/keepalived-1.3.5/COPYING
/usr/share/doc/keepalived-1.3.5/ChangeLog
/usr/share/doc/keepalived-1.3.5/NOTE_vrrp_vmac.txt
/usr/share/doc/keepalived-1.3.5/README
/usr/share/doc/keepalived-1.3.5/TODO
/usr/share/doc/keepalived-1.3.5/keepalived.conf.SYNOPSIS
/usr/share/doc/keepalived-1.3.5/samples
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.HTTP_GET.port
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.IPv6
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.SMTP_CHECK
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.SSL_GET
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.fwmark
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.inhibit
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.misc_check
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.misc_check_arg
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.quorum
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.sample
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.status_code
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.track_interface
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.virtual_server_group
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.virtualhost
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.localcheck
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.lvs_syncd
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.routes
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.rules
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.scripts
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.static_ipaddress
/usr/share/doc/keepalived-1.3.5/samples/keepalived.conf.vrrp.sync
/usr/share/doc/keepalived-1.3.5/samples/sample.misccheck.smbcheck.sh
/usr/share/man/man1/genhash.1.gz
/usr/share/man/man5/keepalived.conf.5.gz
/usr/share/man/man8/keepalived.8.gz
/usr/share/snmp/mibs/KEEPALIVED-MIB.txt
/usr/share/snmp/mibs/VRRP-MIB.txt
/usr/share/snmp/mibs/VRRPv3-MIB.txt[root@KA1 ~]# dnf install keepalived -y
[root@KA1 ~]# systemctl start keepalived
[root@KA1 ~]# ps axf | grep keepalived
2385 pts/0 S+ 0:00 \_ grep --color=auto keepalived
2326 ? Ss 0:00 /usr/sbin/keepalived -D
2327 ? S 0:00 \_ /usr/sbin/keepalived -D2.6 KeepAlived 配置说明
2.6.1 配置文件组成部分
配置文件：/etc/keepalived/keepalived.conf
配置文件组成
·GLOBAL CONFIGURATION
·Global definitions： 定义邮件配置，route_id，vrrp配置，多播地址等
·VRRP CONFIGURATION
VRRP instance(s)： 定义每个vrrp虚拟路由器
·LVS CONFIGURATION
Virtual server group(s)
Virtual server(s)： LVS集群的VS和RS
2.6.2 配置语法说明
帮助
man keepalived.conf2.6.2.1 全局配置
[root@ka1 ~]# vim /etc/keepalived/keepalived.confglobal_defs {
notification_email {
acassen@firewall.loc
failover@firewall.loc
sysadmin@firewall.loc
2282475145@qq.com #发生故障切换时邮件发送的目标邮箱，可以按行区分写多个
}
notification_email_from haha@qq.org #发邮件的地址
smtp_server 172.0.0.1 #邮件服务器地址
smtp_connect_timeout 30 #邮件服务器连接timeout
router_id ka1 #每个keepalived主机唯一标识
#建议使用当前主机名，但多节点
vrrp_skip_check_adv_addr #对所有通告报文都检查，会比较消耗性能
#启用此配置后，如果收到的通告报文和上一个报文是同一 #个路由器，则跳过检查，默认值为全检查
vrrp_strict #严格遵循vrrp协议
#启用此项后以下状况将无法启动服务:
#1.无VIP地址
#2.配置了单播邻居
#3.在VRRP版本2中有IPv6地址
#建议不加此项配置
vrrp_garp_interval 0 #报文发送延迟，0表示不延迟
vrrp_gna_interval 0 #消息发送延迟
vrrp_mcast_group4 224.0.0.18 #指定组播IP地址范围：
}
2.6.2.2 配置虚拟路由器
vrrp_instance VI_1 {
state MASTER
interface eth0 #绑定为当前虚拟路由器使用的物理接口，如：eth0,可以和VIP不在一个网卡
virtual_router_id 51 #每个虚拟路由器惟一标识,范围：0-255，每个虚拟路由器此值必须唯一
#否则服务无法启动
#同属一个虚拟路由器的多个keepalived节点必须相同
#务必要确认在同一网络中此值必须唯一
priority 100 #当前物理节点在此虚拟路由器的优先级，范围：1-254
#值越大优先级越高,每个keepalived主机节点此值不同
advert_int 1 #vrrp通告的时间间隔，默认1s
authentication { #认证机制
auth_type AH|PASS #AH为IPSEC认证(不推荐),PASS为简单密码(建议使用)
auth_pass 1111 #预共享密钥，仅前8位有效
#同一个虚拟路由器的多个keepalived节点必须一样
}
virtual_ipaddress { #虚拟IP,生产环境可能指定上百个IP地址
<IPADDR>/<MASK> brd <IPADDR> dev <STRING> scope <SCOPE> label <LABEL>
172.25.254.100 #指定VIP，不指定网卡，默认为eth0,注意：不指定/prefix,默认32
172.25.254.101/24 dev eth1
172.25.254.102/24 dev eth2 label eth2:1
}
}vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 lable eth0:1
}
}
示例
#配置master端，ka1
[root@KA1 ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
vrrp_strict
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka1 ~]# systemctl enable --now keepalived.service
Created symlink from /etc/systemd/system/multi-user.target.wants/keepalived.service to /usr/lib/systemd/system/keepalived.service.
#配置slave端，ka2
[root@KA2 ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
notification_email {
acassen@firewall.loc
failover@firewall.loc
sysadmin@firewall.loc
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
vrrp_strict
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100 #相同id管理同一个虚拟路由
priority 80 #低优先级
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# systemctl enable --now keepalived.service
Created symlink from /etc/systemd/system/multi-user.target.wants/keepalived.service to /usr/lib/systemd/system/keepalived.service.
#查看是否成功
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 70754 bytes 7169742 (6.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 65410 bytes 5606595 (5.3 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#测试
[root@ka2 ~]# tcpdump -i eth0 -nn host 224.0.0.18
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
11:15:31.584875 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:32.585691 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:33.586961 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:34.587594 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
#关闭KA1后再看组播信息
[root@ka1 ~]# systemctl stop keepalived.service
[root@ka2 ~]# tcpdump -i eth0 -nn host 224.0.0.18
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
11:15:59.322785 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:00.323385 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:01.323864 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:02.324344 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
抓包测试
关闭KA1后再看组播信息
2.6.2.3让vip可以通信
通过上述的方法会出现问题：relserver无法访问172.25.254.100
解决方法：
方法1：（添加vrrp_iptable）
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
vrrp_strict
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
vrrp_iptables #添加
}
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
acassen@firewall.loc
failover@firewall.loc
sysadmin@firewall.loc
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
vrrp_strict
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
vrrp_iptables #添加
}
[root@ka2 ~]# systemctl restart keepalived.service
#查看效果：
#原本
[root@relserver1 ~]# ping 172.25.254.100
PING 172.25.254.100 (172.25.254.100) 56(84) bytes of data.
ping: sendmsg: 网络不可达
^C
--- 172.25.254.100 ping statistics ---
5 packets transmitted, 0 received, 100% packet loss, time 4014ms
#现在
[root@relserver1 ~]# ping 172.25.254.100
PING 172.25.254.100 (172.25.254.100) 56(84) bytes of data.
64 bytes from 172.25.254.100: icmp_seq=2 ttl=64 time=5.63 ms
64 bytes from 172.25.254.100: icmp_seq=3 ttl=64 time=0.255 ms
64 bytes from 172.25.254.100: icmp_seq=4 ttl=64 time=0.296 ms
^C
--- 172.25.254.100 ping statistics ---
4 packets transmitted, 3 received, 25% packet loss, time 3012ms
rtt min/avg/max/mdev = 0.255/2.061/5.634/2.526 ms
#方法2（注释掉vrrp_strict）
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #注释
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
#vrrp_iptables
}
[root@ka1 ~]# systemctl restart keepalived.service
[root@relserver1 ~]# ping 172.25.254.100
PING 172.25.254.100 (172.25.254.100) 56(84) bytes of data.
64 bytes from 172.25.254.100: icmp_seq=1 ttl=64 time=62.3 ms
64 bytes from 172.25.254.100: icmp_seq=2 ttl=64 time=0.375 ms
64 bytes from 172.25.254.100: icmp_seq=3 ttl=64 time=0.505 ms
^C
--- 172.25.254.100 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 0.375/21.083/62.371/29.195 ms
2.6.2.4 启用keepalived日志功能
示例：
#指定日志
[root@KA1 ~]# vim /etc/sysconfig/keepalived
KEEPALIVED_OPTIONS="-D -S 6"
#指定采集方法
[root@ka1 ~]#vim /etc/rsyslog.conf
local6.* /var/log/keepalived.log #前面写的6这个就要写6
#重启服务
[root@ka1 ~]# systemctl restart rsyslog.service
[root@ka1 ~]# systemctl restart keepalived.service
#查看日志
[root@ka1 ~]#tail -f /var/log/keepalived.log
Apr 14 09:25:51 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:51 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:51 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:51 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: (VI_1) Sending/queueing gratuitous
ARPs on eth0 for 10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
Apr 14 09:25:56 ka1 Keepalived_vrrp[1263]: Sending gratuitous ARP on eth0 for
10.0.0.10
2.6.2.5 实现独立子配置文件
当生产环境复杂时， /etc/keepalived/keepalived.conf 文件中内容过多，不易管理将不同集群的配置，比如：不同集群的VIP配置放在独立的子配置文件中利用include 指令可以实现包含子配置文件
格式：
include /path/file[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
#注释
#vrrp_instance VI_1 {
# state MASTER
# interface eth0
# virtual_router_id 100
# priority 100
# advert_int 1
# authentication {
# auth_type PASS
# auth_pass 1111
# }
# virtual_ipaddress {
# 172.25.254.100/24 dev eth0 label eth0:1
# }
#}
#添加
include "/etc/keepalived/conf.d/*.conf" #子配置文件位置
[root@ka1 ~]# mkdir -p /etc/keepalived/conf.d
[root@ka1 ~]# vim /etc/keepalived/conf.d/172.25.254.100.conf
stance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka1 ~]# systemctl restart keepalived.service
三.Keepalived 企业应用示例
3.1 实现master/slave的 Keepalived 单主架构
配置如下：
#配置master端，ka1
[root@KA1 ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #添加此选项无法访问vip
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka1 ~]# systemctl enable --now keepalived.service
Created symlink from /etc/systemd/system/multi-user.target.wants/keepalived.service to /usr/lib/systemd/system/keepalived.service.
#配置slave端，ka2
[root@KA2 ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
notification_email {
acassen@firewall.loc
failover@firewall.loc
sysadmin@firewall.loc
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #添加此选项无法访问vip
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100 #相同id管理同一个虚拟路由
priority 80 #低优先级
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# systemctl enable --now keepalived.service
Created symlink from /etc/systemd/system/multi-user.target.wants/keepalived.service to /usr/lib/systemd/system/keepalived.service.
#查看是否成功
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 70754 bytes 7169742 (6.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 65410 bytes 5606595 (5.3 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#测试
[root@ka2 ~]# tcpdump -i eth0 -nn host 224.0.0.18
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
11:15:31.584875 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:32.585691 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:33.586961 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
11:15:34.587594 IP 172.25.254.10 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
#关闭KA1后再看组播信息
[root@ka1 ~]# systemctl stop keepalived.service
[root@ka2 ~]# tcpdump -i eth0 -nn host 224.0.0.18
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
11:15:59.322785 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:00.323385 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:01.323864 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
11:16:02.324344 IP 172.25.254.20 > 224.0.0.18: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
抓包测试
关闭KA1后再看组播信息
3.2 抢占模式和非抢占模式
3.2.1 非抢占模式 nopreempt
默认为抢占模式preempt，即当高优先级的主机恢复在线后，会抢占低先级的主机的master角色，
这样会使vip在KA主机中来回漂移，造成网络抖动，
建议设置为非抢占模式 nopreempt ，即高优先级主机恢复后，并不会抢占低优先级主机的master角色
非抢占模块下,如果原主机down机, VIP迁移至的新主机, 后续也发生down时,仍会将VIP迁移回原主机
注意：要关闭 VIP抢占，必须将各 keepalived 服务器state配置为BACKUP
设置抢占模式具体步骤：
·注释vrrp_strict（#vrrp_strict）
·各个keeppalived为BACKUP（state BACKUP ）
·添加nopreempt（nopreempt）
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state BACKUP #MASTER改为BACKUP
interface eth0
virtual_router_id 100
priority 100
advert_int 1
nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100
priority 80
advert_int 1
nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# systemctl restart keepalived.service
[root@ka1 ~]# systemctl restart keepalived.service
#测试，ka2拿到了vip
[root@ka2 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.20 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fec2:7175 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
RX packets 291571 bytes 29211263 (27.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 87070 bytes 6946331 (6.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 44 bytes 3500 (3.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 44 bytes 3500 (3.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#测试，ka2拿到vip之后即使ka1的优先级高也无法获得vip
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 292262 bytes 29495280 (28.1 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 73948 bytes 6338605 (6.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#关闭服务
[root@ka2 ~]# systemctl stop keepalived.service
#测试，ka1成功获得vip
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 294689 bytes 29752373 (28.3 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 74153 bytes 6355341 (6.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions
3.2.2 抢占延迟模式 preempt_delay
抢占延迟模式，即优先级高的主机恢复后，不会立即抢回VIP，而是延迟一段时间（默认300s）再抢回VIP
preempt_delay # #指定抢占延迟时间为#s，默认延迟300s注意：需要各keepalived服务器state为BACKUP,并且不要启用 vrrp_strict
设置延迟模式具体步骤（5s为例）：
·注释vrrp_strict（#vrrp_strict）
·各个keeppalived为BACKUP（state BACKUP ）
·添加preempt_delay 5s（preempt_delay 5s）
配置如下：
#配置文件
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #注释掉
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
#vrrp_iptables
}
vrrp_instance VI_1 {
state BACKUP #MASTER变成BACKU
interface eth0
virtual_router_id 100
priority 100
advert_int 1
preempt_delay 5s #延时5s，两边都要添加
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# systemctl restart keepalived.service
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #注释掉
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
#vrrp_iptables
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100
priority 80
advert_int 1
preempt_delay 5s #延时5s，两边都要添加
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
}
[root@ka2 ~]# systemctl restart keepalived.service
#测试
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 299714 bytes 30246564 (28.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 74899 bytes 6413249 (6.1 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#ka1关闭服务
[root@ka1 ~]# systemctl stop keepalived.service
#ka2测试
[root@ka2 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.20 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fec2:7175 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
RX packets 299775 bytes 30060475 (28.6 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 87589 bytes 6994507 (6.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 44 bytes 3500 (3.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 44 bytes 3500 (3.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#重启ka1的服务，等5s之后vip又回来了
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 301756 bytes 30457843 (29.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 75227 bytes 6444329 (6.1 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 649 bytes 47761 (46.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 649 bytes 47761 (46.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 
ka1
ka2
3.3 VIP单播配置
默认keepalived主机之间利用多播相互通告消息，会造成网络拥塞，可以替换成单播，减少网络流量
注意：启用 vrrp_strict 时，不能启用单播
#在所有节点vrrp_instance语句块中设置对方主机的IP，建议设置为专用于对应心跳线网络的地址，而非使用业务网络
unicast_src_ip <IPADDR> #指定发送单播的源IP
unicast_peer {
<IPADDR> #指定接收单播的对方目标主机IP
......
}
#启用 vrrp_strict 时，不能启用单播,否则服务无法启动,并在messages文件中记录下面信息
Jun 16 17:50:06 centos8 Keepalived_vrrp[23180]: (m44) Strict mode does not
support authentication. Ignoring.
Jun 16 17:50:06 centos8 Keepalived_vrrp[23180]: (m44) Unicast peers are not
supported in strict mode
Jun 16 17:50:06 centos8 Keepalived_vrrp[23180]: Stopped - used 0.000606 user
time, 0.000000 system time
Jun 16 17:50:06 centos8 Keepalived[23179]: Keepalived_vrrp exited with permanent
error CONFIG. Terminating
Jun 16 17:50:06 centos8 systemd[1]: keepalived.service: Succeeded.
Jun 16 17:50:06 centos8 Keepalived[23179]: Stopped Keepalived v2.0.10
(11/12,2018)vip单播配置具体步骤：
·注释vrrp_strict（#vrrp_strict）
·一个keeppalived为MASTER一个keeppalived为BACKUP（state MASTER，state BACKUP ）（都为BACKUP也可以）
·添加（两边都写）：
unicast_src_ip 172.25.254.10 #本机IP
unicast_peer {
172.25.254.20 #指向对方主机IP，如果有多个keepalived,再加其它节点的IP
}
配置如下：
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #注释此参数，与vip单播模式冲突
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
#vrrp_iptables
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.10 #本机IP
unicast_peer {
172.25.254.20 #指向对方主机IP，如果有多个keepalived,再加其它节点的IP
}
}
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
global_defs {
notification_email {
2282475145@qq.com
}
notification_email_from haha@qq.org
smtp_server 172.0.0.1
smtp_connect_timeout 30
router_id ka1
vrrp_skip_check_adv_addr
#vrrp_strict #注释此参数，与vip单播模式冲突
vrrp_garp_interval 0
vrrp_gna_interval 0
vrrp_mcast_group4 224.0.0.18
#vrrp_iptables
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100
priority 80
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.20
unicast_peer {
172.25.254.10
}
}
[root@ka2 ~]# systemctl restart keepalived.service
#抓包查看单播效果，-i指定网卡
[root@ka1 ~]# tcpdump -i eth0 -nn src host 172.25.254.10 and dst 172.25.254.20
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
14:29:44.867773 IP 172.25.254.10 > 172.25.254.20: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
14:29:45.869259 IP 172.25.254.10 > 172.25.254.20: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
14:29:46.870494 IP 172.25.254.10 > 172.25.254.20: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
14:29:47.871914 IP 172.25.254.10 > 172.25.254.20: VRRPv2, Advertisement, vrid 100, prio 100, authtype simple, intvl 1s, length 20
[root@ka1 ~]# systemctl stop keepalived.service
[root@ka2 ~]# tcpdump -i eth0 -nn src host 172.25.254.20 and dst 172.25.254.10
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
14:30:33.763918 IP 172.25.254.20 > 172.25.254.10: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
14:30:34.764841 IP 172.25.254.20 > 172.25.254.10: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
14:30:35.765366 IP 172.25.254.20 > 172.25.254.10: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
14:30:36.766232 IP 172.25.254.20 > 172.25.254.10: VRRPv2, Advertisement, vrid 100, prio 80, authtype simple, intvl 1s, length 20
抓包查看单播效果
ka1
ka2
3.4 Keepalived 通知脚本配置
当keepalived的状态变化时，可以自动触发脚本的执行，比如：发邮件通知用户
默认以用户keepalived_script身份执行脚本
如果此用户不存在，以root执行脚本可以用下面指令指定脚本执行用户的身份
global_defs {
......
script_user <USER>
......
}3.4.1 通知脚本类型
当前节点成为主节点时触发的脚本
notify_master <STRING>|<QUOTED-STRING>当前节点转为备节点时触发的脚本
notify_backup <STRING>|<QUOTED-STRING>当前节点转为“失败”状态时触发的脚本
notify_fault <STRING>|<QUOTED-STRING>通用格式的通知触发机制，一个脚本可完成以上三种状态的转换时的通知
notify <STRING>|<QUOTED-STRING>当停止VRRP时触发的脚本
notify_stop <STRING>|<QUOTED-STRING>3.4.2 脚本的调用方法
在 vrrp_instance VI_1 语句块的末尾加下面行
notify_master "/etc/keepalived/notify.sh master"
notify_backup "/etc/keepalived/notify.sh backup"
notify_fault "/etc/keepalived/notify.sh fault"3.4.3 创建通知脚本
[root@ka1 ~]# vim /etc/keepalived/mail.sh
#!/bin/bash
mail_dest='2282475145@qq.com'
mail_message()
{
mail_sub="$HOSTNAME to be $1 vip 转移"
mail_msg="`date +%F\ %T`: vrrp 转移,$HOSTNAME 变为 $1"
echo "$mail_msg" | mail -s "$mail_sub" $mail_dest
}
case $1 in
master)
mail_message master
;;
backup)
mail_message backup
;;
fault)
mail_message fault
;;
*)
exit 1
;;
esac3.4.4 邮件配置
安装邮件发送工具
#下载mail
[root@ka1 ~]# yum install mailx -y
[root@ka2 ~]# yum install mailx -yQQ邮箱配置
[root@KA1 ~]# vim /etc/mail.rc
#######mail set##########
#在最后添加
set from=2282475145@qq.com
set smtp=smtp.qq.com
set smtp-auth-user=2282475145@qq.com
set smtp-auth-password=glrywpzthhdzecie #授权码
set smtp-auth=login
set ssl-verify=ignore
发送测试邮件
[root@KA1 ~]# echo test message |mail -s test 2282475145@qq.com使用上面的方法后邮箱会收到一封邮件
3.4.5 实战案例：实现 Keepalived 状态切换的通知脚本
[root@ka2 ~]# vim /etc/keepalived/mail.sh
#!/bin/bash
mail_dest='2282475145@qq.com'
mail_message()
{
mail_sub="$HOSTNAME to be $1 vip 转移"
mail_msg="`date +%F\ %T`: vrrp 转移,$HOSTNAME 变为 $1"
echo "$mail_msg" | mail -s "$mail_sub" $mail_dest
}
case $1 in
master)
mail_message master
;;
backup)
mail_message backup
;;
fault)
mail_message fault
;;
*)
exit 1
;;
esac
#添加权限
[root@ka2 ~]# chmod +x /etc/keepalived/mail.sh
#测试脚本
[root@ka1 ~]# bash /etc/keepalived/mail.sh master
#添加引用脚本的配置
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.10
unicast_peer {
172.25.254.20
}
notify_master "/etc/keepalived/mail.sh master"
notify_backup "/etc/keepalived/mail.sh backup"
notify_fault "/etc/keepalived/mail.sh fault"
}
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 100
priority 80
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.20
unicast_peer {
172.25.254.10
}
notify_master "/etc/keepalived/mail.sh master"
notify_backup "/etc/keepalived/mail.sh backup"
notify_fault "/etc/keepalived/mail.sh fault"
}
[root@ka2 ~]# systemctl restart keepalived.service
#重启服务后会收到邮件脚本如下：
测试：在浏览器中观察邮件即可
3.5 实现 master/master 的 Keepalived 双主架构
master/slave的单主架构，同一时间只有一个Keepalived对外提供服务，此主机繁忙，而另一台主机却很空闲，利用率低下，可以使用master/master的双主架构，解决此问题。
master/master 的双主架构：
即将两个或以上VIP分别运行在不同的keepalived服务器，以实现服务器并行提供web访问的目的，提高服务器资源利用率
主备需要修改的地方：
·state MASTER（BACKUP）
·virtual_router_id 100（两个主机的一个主备的ip要相同）
·priority 100（主的优先级要高于备用的）
·虚拟的IP如下：
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1 #同一个主备ip要相同，网卡要相同且没有被占用
}
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state MASTER #主
interface eth0
virtual_router_id 100
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.10
unicast_peer {
172.25.254.20
}
# notify_master "/etc/keepalived/mail.sh master"
# notify_backup "/etc/keepalived/mail.sh backup"
# notify_fault "/etc/keepalived/mail.sh fault"
}
vrrp_instance VI_2 {
state BACKUP #备
interface eth0
virtual_router_id 200
priority 80
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.200/24 dev eth0 label eth0:2
}
unicast_src_ip 172.25.254.10
unicast_peer {
172.25.254.20
}
# notify_master "/etc/keepalived/mail.sh master"
# notify_backup "/etc/keepalived/mail.sh backup"
# notify_fault "/etc/keepalived/mail.sh fault"
}
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state BACKUP #备
interface eth0
virtual_router_id 100
priority 80
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.20
unicast_peer {
172.25.254.10
}
# notify_master "/etc/keepalived/mail.sh master"
# notify_backup "/etc/keepalived/mail.sh backup"
# notify_fault "/etc/keepalived/mail.sh fault"
}
vrrp_instance VI_2 {
state MASTER #主
interface eth0
virtual_router_id 200
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.200/24 dev eth0 label eth0:2
}
unicast_src_ip 172.25.254.20
unicast_peer {
172.25.254.10
}
# notify_master "/etc/keepalived/mail.sh master"
# notify_backup "/etc/keepalived/mail.sh backup"
# notify_fault "/etc/keepalived/mail.sh fault"
}
[root@ka2 ~]# systemctl restart keepalived.service
#测试
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 513894 bytes 51976853 (49.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 96148 bytes 8275534 (7.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 655 bytes 48137 (47.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 655 bytes 48137 (47.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@ka2 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.20 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fec2:7175 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
RX packets 513134 bytes 51651531 (49.2 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 106890 bytes 8453025 (8.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.200 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 46 bytes 3598 (3.5 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 46 bytes 3598 (3.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#关闭ka2测试
[root@ka2 ~]# systemctl stop keepalived.service
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 515312 bytes 52094815 (49.6 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 96317 bytes 8290464 (7.9 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
eth0:2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.200 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 655 bytes 48137 (47.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 655 bytes 48137 (47.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ka1
主
备
ka2
测试：
关掉ka2的keepalive服务后
实战案例：三个节点的三主架构实现
#第一个节点ka1配置：
Vrrp instance 1：MASTER，优先级100
Vrrp instance 2：BACKUP，优先级80
Vrrp instance 3：BACKUP，优先级60
#第二个节点ka2配置：
Vrrp instance 1：BACKUP，优先级60
Vrrp instance 2：MASTER，优先级100
Vrrp instance 3：BACKUP，优先级80
#第三个节点ka3配置：
Vrrp instance 1：BACKUP，优先级80
Vrrp instance 2：BACKUP，优先级60
Vrrp instance 3：MASTER，优先级100
3.6 实现IPVS的高可用性
3.6.1 IPVS相关配置
3.6.1.1 虚拟服务器配置结构
virtual_server IP port {
...
real_server {
...
}
real_server {
...
}
…
}3.6.1.2 virtual server （虚拟服务器）的定义格式
virtual_server IP port #定义虚拟主机IP地址及其端口
virtual_server fwmark int #ipvs的防火墙打标，实现基于防火墙的负载均衡集群
virtual_server group string #使用虚拟服务器组3.6.1.3 虚拟服务器配置
virtual_server IP port { #VIP和PORT
delay_loop <INT> #检查后端服务器的时间间隔
lb_algo rr|wrr|lc|wlc|lblc|sh|dh #定义调度方法
lb_kind NAT|DR|TUN #集群的类型,注意要大写
persistence_timeout <INT> #持久连接时长
protocol TCP|UDP|SCTP #指定服务协议,一般为TCP
sorry_server <IPADDR> <PORT> #所有RS故障时，备用服务器地址
real_server <IPADDR> <PORT> { #RS的IP和PORT
weight <INT> #RS权重
notify_up <STRING>|<QUOTED-STRING> #RS上线通知脚本
notify_down <STRING>|<QUOTED-STRING> #RS下线通知脚本
HTTP_GET|SSL_GET|TCP_CHECK|SMTP_CHECK|MISC_CHECK { ... } #定义当前主机健康状态检测方法
}
}
#注意:括号必须分行写,两个括号写在同一行,如: }} 会出错3.6.1.4 应用层监测
应用层检测：HTTP_GET|SSL_GET
HTTP_GET|SSL_GET {
url {
path <URL_PATH> #定义要监控的URL
status_code <INT> #判断上述检测机制为健康状态的响应码，一般为 200
}
connect_timeout <INTEGER> #客户端请求的超时时长, 相当于haproxy的timeout server
nb_get_retry <INT> #重试次数
delay_before_retry <INT> #重试之前的延迟时长
connect_ip <IP ADDRESS> #向当前RS哪个IP地址发起健康状态检测请求
connect_port <PORT> #向当前RS的哪个PORT发起健康状态检测请求
bindto <IP ADDRESS> #向当前RS发出健康状态检测请求时使用的源地址
bind_port <PORT> #向当前RS发出健康状态检测请求时使用的源端口
}3.6.1.5 TCP监测
传输层检测：TCP_CHECK
TCP_CHECK {
connect_ip <IP ADDRESS> #向当前RS的哪个IP地址发起健康状态检测请求
connect_port <PORT> #向当前RS的哪个PORT发起健康状态检测请求
bindto <IP ADDRESS> #发出健康状态检测请求时使用的源地址
bind_port <PORT> #发出健康状态检测请求时使用的源端口
connect_timeout <INTEGER> #客户端请求的超时时长
#等于haproxy的timeout server
}3.6.2 实战案例
3.6.2.1 实战案例1：实现单主的 LVS-DR 模式
准备web服务器并使用脚本绑定VIP至web服务器lo网卡
具体流程：
·rel主机需要有vip（可以在虚拟网卡中添加）
·rel主机需要关闭arp的响应
·ka1和ka2编写keepalive配置文件
#安装httpd
[root@relserver1 ~]# yum install httpd -y
[root@relserver1 ~]# echo rel - 172.25.254.110 > /var/www/html/index.html
[root@relserver1 ~]# systemctl start httpd
[root@relserver2 ~]# yum install httpd -y
[root@relserver2 ~]# echo rel - 172.25.254.120 > /var/www/html/index.html
[root@relserver2 ~]# systemctl start httpd
#准备两台后端RS主机
[root@relserver1 ~]# ip addr add 172.25.254.100/32 dev lo
[root@relserver2 ~]# ip addr add 172.25.254.100/32 dev lo
#如果想要永久设置，可以在环回的配置文件中直接更改
[root@ka1 ~]# vim /etc/sysconfig/network-scripts/ifcfg-lo
#在里面修改ip和掩码即可
#然后重启
[root@ka1 ~]# systemctl restart network
#关闭响应（临时的）
[root@relserver1 ~]# echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore
[root@relserver1 ~]# echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore
[root@relserver1 ~]# echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce
[root@relserver1 ~]# echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce
#关闭响应（永久的）
[root@relserver2 ~]# sysctl -a | grep arp
dev.parport.default.spintime = 500
dev.parport.default.timeslice = 200
net.ipv4.conf.all.arp_accept = 0
net.ipv4.conf.all.arp_announce = 0
net.ipv4.conf.all.arp_filter = 0
net.ipv4.conf.all.arp_ignore = 0
net.ipv4.conf.all.arp_notify = 0
。。。。。
#写配置文件
[root@relserver2 ~]# vim /etc/sysctl.d/arp.conf
net.ipv4.conf.all.arp_ignore=1
net.ipv4.conf.all.arp_announce=2
net.ipv4.conf.lo.arp_ignore=1
net.ipv4.conf.lo.arp_announce=2
#重启
[root@relserver2 ~]# sysctl --system
* Applying /usr/lib/sysctl.d/00-system.conf ...
* Applying /usr/lib/sysctl.d/10-default-yama-scope.conf ...
kernel.yama.ptrace_scope = 0
* Applying /usr/lib/sysctl.d/50-default.conf ...
kernel.sysrq = 16
kernel.core_uses_pid = 1
kernel.kptr_restrict = 1
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.default.accept_source_route = 0
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.promote_secondaries = 1
fs.protected_hardlinks = 1
fs.protected_symlinks = 1
* Applying /usr/lib/sysctl.d/60-libvirtd.conf ...
fs.aio-max-nr = 1048576
* Applying /etc/sysctl.d/99-sysctl.conf ...
* Applying /etc/sysctl.d/arp.conf ...
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.lo.arp_ignore = 1
net.ipv4.conf.lo.arp_announce = 2
* Applying /etc/sysctl.conf ...
#下载ipvsadm，便于检测
[root@ka1 ~]# yum install ipvsadm -y
[root@ka2 ~]# yum install ipvsadm -y
#编写配置文件
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
virtual_server 172.25.254.100 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
persistence_timeout 50
protocol TCP
real_server 172.25.254.110 80 {
weight 1
HTTP_GET {
url {
path /
status_code 200
}
connect_timeout 3
nb_get_retry 2
delay_before_retry 2
}
}
real_server 172.25.254.120 80 {
weight 1
HTTP_GET {
url {
path /
status_code 200
}
connect_timeout 3
nb_get_retry 2
delay_before_retry 2
}
}
}
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
virtual_server 172.25.254.100 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
protocol TCP
real_server 172.25.254.110 80 {
weight 1
HTTP_GET {
url {
path /
status_code 200
}
connect_timeout 3
nb_get_retry 2
delay_before_retry 2
}
}
real_server 172.25.254.120 80 {
weight 1
HTTP_GET {
url {
path /
status_code 200
}
connect_timeout 3
nb_get_retry 2
delay_before_retry 2
}
}
}
[root@ka2 ~]# systemctl restart keepalived.service
#测试
[root@ka1 ~]# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.200.100:443 rr persistent 50
TCP 10.10.10.2:1358 rr persistent 50
-> 192.168.200.200:1358 Masq 1 0 0
TCP 10.10.10.3:1358 rr persistent 50
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka1 ~]# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 172.25.254.100:80 wrr persistent 50
-> 172.25.254.110:80 Route 1 0 0
-> 172.25.254.120:80 Route 1 0 0
TCP 192.168.200.100:443 rr persistent 50
-> 192.168.201.100:443 Masq 1 0 0
TCP 10.10.10.2:1358 rr persistent 50
-> 192.168.200.2:1358 Masq 1 0 0
-> 192.168.200.3:1358 Masq 1 0 0
#模拟故障
#关闭一个http服务进行测试
[root@relserver1 ~]# systemctl stop httpd.service
[root@ka1 ~]# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 172.25.254.100:80 wrr persistent 50
-> 172.25.254.120:80 Route 1 0 0
TCP 192.168.200.100:443 rr persistent 50
TCP 10.10.10.2:1358 rr persistent 50
-> 192.168.200.200:1358 Masq 1 0
#关闭ka1的keepalive
[root@ka1 ~]# systemctl stop keepalived.service
[root@ka1 ~]# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.0.100:80 wrr
[root@ka2 ~]# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 172.25.254.100:80 wrr
-> 172.25.254.120:80 Route 1 0 0
TCP 192.168.200.100:443 rr persistent 50
TCP 10.10.10.3:1358 rr persistent 50
#访问测试
[root@ka2 ~]# curl 172.25.254.100
rel - 172.25.254.120
[root@ka2 ~]# curl 172.25.254.100
rel - 172.25.254.110
[root@ka2 ~]# curl 172.25.254.100
rel - 172.25.254.120
[root@ka2 ~]# curl 172.25.254.100
rel - 172.25.254.110
关闭arp响应
永久关闭的配置文件如下：
编写配置文件
rel1：
rel2：
理解：
类似于：
类似于：
测试：
模拟故障
关闭一个http服务后，再进行测试
关闭ka1的keepalive
ka1
ka2
但由于是抢占模式，即使此时开启了ka1的keepalive也无法获得
访问测试：
3.7 实现其它应用的高可用性 VRRP Script
keepalived利用 VRRP Script 技术，可以调用外部的辅助脚本进行资源监控，并根据监控的结果实现优先
动态调整，从而实现其它应用的高可用性功能
参考配置文件：/usr/share/doc/keepalived/keepalived.conf.vrrp.localcheck
总结：vrrp_script中可以运行一个脚本，而这个脚本检测某个文件是否存在返回一个值，如果这个值是非零则会根据策略选择降低或者提高优先级。
3.7.1 VRRP Script 配置
分两步实现：
·定义脚本
vrrp_script：自定义资源监控脚本，vrrp实例根据脚本返回值，公共定义，可被多个实例调用，定义在vrrp实例之外的独立配置块，一般放在global_defs设置块之后。
通常此脚本用于监控指定应用的状态。一旦发现应用的状态异常，则触发对MASTER节点的权重减至低于SLAVE节点，从而实现 VIP 切换到 SLAVE 节点
#定义脚本
vrrp_script <SCRIPT_NAME> {
script <STRING>|<QUOTED-STRING> #此脚本返回值为非0时，会触发下面OPTIONS执行
OPTIONS
}·调用脚本
track_script：调用vrrp_script定义的脚本去监控资源，定义在VRRP实例之内，调用事先定义的vrrp_script
#调用脚本
track_script {
SCRIPT_NAME_1
SCRIPT_NAME_2
}3.7.1.1 定义 VRRP script
vrrp_script <SCRIPT_NAME> { #定义一个检测脚本，在global_defs 之外配置（也可以在下面配置）
script <STRING>|<QUOTED-STRING> #shell命令或脚本路径
interval <INTEGER> #间隔时间，单位为秒，默认1秒
timeout <INTEGER> #超时时间
weight <INTEGER:-254..254> #默认为0,如果设置此值为负数，
#当上面脚本返回值为非0时
#会将此值与本节点权重相加可以降低本节点权重，
#即表示fall.
#如果是正数，当脚本返回值为0，
#会将此值与本节点权重相加可以提高本节点权重
#即表示 rise.通常使用负值
fall <INTEGER> #执行脚本连续几次都失败,则转换为失败，建议设为2以上
rise <INTEGER> #执行脚本连续几次都成功，把服务器从失败标记为成功
user USERNAME [GROUPNAME] #执行监测脚本的用户或组
init_fail #设置默认标记为失败状态，监测成功之后再转换为成功状态
}
3.7.1.2 调用 VRRP script
vrrp_instance test {
... ...
track_script {
check_down
}
}3.7.2 实战案例：利用脚本实现主从角色切换
[root@ka1 ~]# vim /etc/keepalived/test.sh
#!/bin/bash
[ ! -f "/mnt/haha" ] #判断有没有这个haha文件，没有就为真（0）
[root@ka1 ~]# chmod +x /etc/keepalived/test.sh
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
vrrp_script check_file {
script "/etc/keepalived/test.sh" #为非0的时候执行,即haha存在的时候-30
interval 1
weight -30
fall 2
rise 2
timeout 2
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.10
unicast_peer {
172.25.254.20
}
track_script {
check_file
}
}
[root@ka1 mnt]# systemctl restart keepalived.service
#没有haha文件时
[root@ka1 mnt]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 737477 bytes 70679904 (67.4 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 126567 bytes 10684608 (10.1 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 655 bytes 48137 (47.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 655 bytes 48137 (47.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#有haha文件时
[root@ka1 mnt]# touch haha
[root@ka1 mnt]# systemctl restart keepalived.service
[root@ka1 mnt]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 945796 bytes 87514535 (83.4 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 152652 bytes 12586792 (12.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 655 bytes 48137 (47.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 655 bytes 48137 (47.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
没有haha文件时
有haha文件时，会100-30=70<80，vip会转移到ka2中
3.7.3 实战案例：实现HAProxy高可用
#在两个ka1和ka2先实现haproxy的配置
[root@ka1 ~]# yum install haproxy -y
[root@ka2 ~]# yum install haproxy -y
[root@ka1 ~]# vim /etc/haproxy/haproxy.cfg
listen webcluster
bind 172.25.254.100:80
mode http
balance roundrobin
server web1 172.25.254.110:80 check inter 3 fall 2 rise 5
server web2 172.25.254.120:80 check inter 3 fall 2 rise 5
[root@ka2 ~]# vim /etc/haproxy/haproxy.cfg
listen webcluster
bind 172.25.254.100:80
mode http
balance roundrobin
server web1 172.25.254.110:80 check inter 3 fall 2 rise 5
server web2 172.25.254.120:80 check inter 3 fall 2 rise 5
#启动haproxy服务
[root@ka1 ~]# systemctl enable --now haproxy.service
Created symlink from /etc/systemd/system/multi-user.target.wants/haproxy.service to /usr/lib/systemd/system/haproxy.service.
[root@ka2 ~]# systemctl enable --now haproxy.service
Created symlink from /etc/systemd/system/multi-user.target.wants/haproxy.service to /usr/lib/systemd/system/haproxy.service.
#在两个ka1和ka2两个节点启用内核参数，即使本地没有172.25.254.100的iphaproxy也可以启动
[root@ka1 ~]# vim /etc/sysctl.conf
net.ipv4.ip_nonlocal_bind = 1
[root@ka1 ~]# sysctl -p
net.ipv4.ip_nonlocal_bind = 1
[root@ka2 ~]# vim /etc/sysctl.conf
net.ipv4.ip_nonlocal_bind = 1
[root@ka2 ~]# sysctl -p
net.ipv4.ip_nonlocal_bind = 1
#还原环境
#去除上面配置的vip，原本就是临时配置的所以可以使用此方法
[root@relserver1 ~]# systemctl restart network
[root@relserver2 ~]# systemctl restart network
#去除arp
[root@relserver1 ~]# echo 0 > /proc/sys/net/ipv4/conf/all/arp_ignore
[root@relserver1 ~]# echo 0 > /proc/sys/net/ipv4/conf/lo/arp_ignore
[root@relserver1 ~]# echo 0 > /proc/sys/net/ipv4/conf/lo/arp_announce
[root@relserver1 ~]# echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce
#rel2配置的是永久配置，用此方法
[root@relserver2 ~]# vim /etc/sysctl.d/arp.conf
net.ipv4.conf.all.arp_ignore=0
net.ipv4.conf.all.arp_announce=0
net.ipv4.conf.lo.arp_ignore=0
net.ipv4.conf.lo.arp_announce=0
[root@relserver2 ~]# sysctl --system
#注释上文lvs的访问
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
#virtual_server 172.25.254.100 80 {
# delay_loop 6
# lb_algo wrr
# lb_kind DR
# persistence_timeout 50
# protocol TCP
#
# real_server 172.25.254.110 80 {
# weight 1
# HTTP_GET {
# url {
# path /
# status_code 200
# }
# connect_timeout 3
# nb_get_retry 2
# delay_before_retry 2
# }
# }
#
# real_server 172.25.254.120 80 {
# weight 1
# HTTP_GET {
# url {
# path /
# status_code 200
# }
# connect_timeout 3
# nb_get_retry 2
# delay_before_retry 2
# }
# }
#}
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
#virtual_server 172.25.254.100 80 {
# delay_loop 6
# lb_algo wrr
# lb_kind DR
# protocol TCP
#
#
# real_server 172.25.254.110 80 {
# weight 1
# HTTP_GET {
# url {
# path /
# status_code 200
# }
# connect_timeout 3
# nb_get_retry 2
# delay_before_retry 2
# }
# }
#
# real_server 172.25.254.120 80 {
# weight 1
# HTTP_GET {
# url {
# path /
# status_code 200
# }
# connect_timeout 3
# nb_get_retry 2
# delay_before_retry 2
# }
# }
#}
#访问测试
[root@ka1 ~]# systemctl restart keepalived.service
[root@ka2 ~]# systemctl restart keepalived.service
[root@ka1 ~]# curl 172.25.254.100
rel - 172.25.254.120
[root@ka1 ~]# curl 172.25.254.100
rel - 172.25.254.110
#在ka1中编写检测脚本
[root@ka1 ~]# vim /etc/keepalived/test1.sh
#!/bin/bash
killall -0 haproxy
[root@ka2 ~]# vim /etc/keepalived/test1.sh
#!/bin/bash
killall -0 haproxy
[root@ka1 ~]# chmod +x /etc/keepalived/test1.sh
[root@ka2 ~]# chmod +x /etc/keepalived/test1.sh
#配置keepalived
[root@ka1 ~]# vim /etc/keepalived/keepalived.conf
vrrp_script check_haproxy {
script "/etc/keepalived/test1.sh" #为非0的时候执行,即haha存在的时候-30
interval 1
weight -30
fall 2
rise 2
timeout 2
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 100
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.100/24 dev eth0 label eth0:1
}
unicast_src_ip 172.25.254.10
unicast_peer {
172.25.254.20
}
track_script {
check_haproxy
}
}
[root@ka1 ~]# systemctl restart keepalived.service
#由于是双主的配置，所以写在ka2的主上
[root@ka2 ~]# vim /etc/keepalived/keepalived.conf
vrrp_script check_haproxy {
script "/etc/keepalived/test1.sh" #为非0的时候执行,即haha存在的时候-30
interval 1
weight -30
fall 2
rise 2
timeout 2
}
vrrp_instance VI_2 {
state MASTER
interface eth0
virtual_router_id 200
priority 100
advert_int 1
#preempt_delay 5s
#nopreempt
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
172.25.254.200/24 dev eth0 label eth0:2
}
unicast_src_ip 172.25.254.20
unicast_peer {
172.25.254.10
}
track_script {
check_haproxy
}
}
[root@ka2 ~]# systemctl restart keepalived.service
#测试，关闭ka1的haproxy服务
#原本
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 1775928 bytes 150099938 (143.1 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1537220 bytes 109628444 (104.5 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 96217 bytes 20634611 (19.6 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 96217 bytes 20634611 (19.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
#关掉之后
[root@ka1 ~]# systemctl stop haproxy.service
[root@ka1 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.10 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fe73:deb2 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:73:de:b2 txqueuelen 1000 (Ethernet)
RX packets 1833904 bytes 154510389 (147.3 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1629301 bytes 116153484 (110.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 102308 bytes 21946985 (20.9 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 102308 bytes 21946985 (20.9 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@ka2 ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.20 netmask 255.255.255.0 broadcast 172.25.254.255
inet6 fe80::20c:29ff:fec2:7175 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
RX packets 1137999 bytes 102802961 (98.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 185423 bytes 14349468 (13.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth0:1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.100 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
eth0:2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.25.254.200 netmask 255.255.255.0 broadcast 0.0.0.0
ether 00:0c:29:c2:71:75 txqueuelen 1000 (Ethernet)
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 10478 bytes 528092 (515.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 10478 bytes 528092 (515.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:f1:ee:92 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
两边都配置
ka1
ka2
测试，ka1关闭haproxy
原
现
ka2
扫一扫
767
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
