一:功能介绍
1、采用stm32单片机+LCD1602+DS18B20温度传感器+蜂鸣器+按键+电机,制作一个基于stm32单片机游泳池水温监测控制系统;
2、通过按键进行设置温度的阈值,并且显示到LCD1602显示屏上面;
3、DS18B20传感器检测实时温度,显示到LCD1602显示屏上面;
4、当实时检测的温度低于设置的温度阈值,开启蜂鸣器提醒,并且打开加热电机进行加热;
二:仿真演示视频+程序简要讲解:(程序有中文注释,新手容易看懂)
130-基于stm32单片机游泳池水温监测控制系统Proteus仿真+源程序
三:设计软件介绍
本设计使用C语言编程设计,程序代码采用keil5编写,程序有中文注释,新手容易看懂,仿真采用Proteus软件进行仿真,演示视频使用的是Proteus8.9版本;资料包里有相关软件包,可自行下载安装。
四:程序打开方法
特别注意:下载资料包以后一定要先解压!!!(建议解压到桌面上,文件路径太深会导致程序打开异常),解压后再用keil5打开。
程序部分展示,有中文注释,新手容易看懂
//按键扫描,获取按键状态
/*****************引脚配置********************/
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,ENABLE);
//LCD1602 管脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8| GPIO_Pin_9| GPIO_Pin_10| GPIO_Pin_11| GPIO_Pin_12| GPIO_Pin_13| GPIO_Pin_14| GPIO_Pin_15;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7 |GPIO_Pin_6|GPIO_Pin_5;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
}
void IO_out( void )
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOC ,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
//按键
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0| GPIO_Pin_1| GPIO_Pin_2| GPIO_Pin_3;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD;;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
}
void Delay_DS18B20(int num)
{
while(num--) ;
}
void anjiansaomiao(void)
{
//表明按下
if(k1 == 1)
{
wenduset++; while(k1!=0);
if(wenduset>100) wenduset=100;
}
//表明按下
if(k2 == 1)
{
wenduset--; while(k2!=0);
if(wenduset<1) wenduset=1;
}
}
int main(void)
{
int t;
short tem,tem1;
GPIO_Configuration();//初始化
Init1602();
IO_out();
delay_init();
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitTypeDef g;
g.GPIO_Mode = GPIO_Mode_Out_PP;
g.GPIO_Speed = GPIO_Speed_10MHz;
g.GPIO_Pin = GPIO_Pin_8 ;
GPIO_Init(GPIOA,&g);
GPIO_SetBits(GPIOA,GPIO_Pin_8); //输出1
t=DS18B20_DQ_IN;
while(t){
DS18B20_IO_OUT(); //SET PG11 OUTPUT
DS18B20_DQ_OUT=0; //拉低DQ
Delay_DS18B20(750); //拉低750us
DS18B20_DQ_OUT=1; //DQ=1
Delay_DS18B20(15); //15US
DS18B20_IO_IN(); //SET PG11 INPUT
Delay_DS18B20(100);
t=DS18B20_DQ_IN;
}
tem=DS18B20_Get_Temp();//读取温度
Delay_DS18B20(1000000);
while(1)
{
tem=DS18B20_Get_Temp();//读取温度
if( tem>0)
{
WrByte1602(0,8,'+');
WrByte1602(0,9,AsciiCode[tem%1000/100]);//显示+温度
WrByte1602(0,10,AsciiCode[tem%100/10]);
WrByte1602(0,12,AsciiCode[tem%10]);
}
else
{
tem1=-(tem);
tem1=tem1+1;
WrByte1602(0,8,'-');
WrByte1602(0,9,AsciiCode[tem1%1000/100]);//显示-温度
WrByte1602(0,10,AsciiCode[tem1%100/10]);
WrByte1602(0,12,AsciiCode[tem1%10]);
}
anjiansaomiao();//扫描按键
WrByte1602(1,10,AsciiCode[wenduset%1000/100]); //显示设置温度
WrByte1602(1,11,AsciiCode[wenduset%100/10]);
WrByte1602(1,12,AsciiCode[wenduset%10]);
if(tem/10<wenduset) PCout(10)=0;//温度小于设置值 开启加热和提醒
else PCout(10)=1;
WrByte1602(0,1,' '); //字符显示
WrByte1602(0,2,'T');
WrByte1602(0,3,'E');
WrByte1602(0,4,'M');
WrByte1602(0,5,'P');
WrByte1602(0,6,'=');
WrByte1602(1,1,' '); //字符显示
WrByte1602(1,2,' ');
WrByte1602(1,3,'S');
WrByte1602(1,4,'E');
WrByte1602(1,5,'T');
WrByte1602(1,6,'=');
WrByte1602(0,11,'.');
WrByte1602(0,14,'C');
WrByte1602(1,14,'C');
五:仿真文件(采用Proteus打开)
六:资料清单展示(文件中包含的相关资料)