文章目录
一、OLED驱动(硬件SPI)
首先参照此CubeMX配置方法得到MDK工程。
下一步代码移植。此处应用中景园官方例程进行修改,移植的文件包括:
- oled.c
- oled.h
- oledfont.h
一些注意事项
- 使用HAL库不再需要原来的delay函数,其对应HAL库函数为:HAL_Delay。
- 在移植oled.c过程中曾出现“ error: #20: identifier “hspi1” is undefined”的错误。由于C语言基础不够扎实,最后发现未在应用main.c头文件下方加上“extern SPI_HandleTypeDef hspi1; ”。
- 使用硬件spi需要重写原来的OLED_WR_Byte函数。
- spi具体函数学习详见“stm32f1xx_hal_spi.c”。
- main函数记得要初始化OLED!(while(1)外)。
- 保存了新文件要记得在魔术棒C/C++处跟踪它的路径,防止编译器出现“找不到对应文件”的错误。
接线
D0(SCL)-PA5
D1(SDA)-PA7
RES-PC4(VET6)-PA3(C6T6)
DC-PC13(VET6)-PA2(C6T6)
CS-PE5(VET6)-PA4(C6T6)
二、代码段
1.oled.c
#include "oled.h"
#include "oledfont.h"
//OLED的显存
//存放格式如下:
//[0]0 1 2 3 ... 127
//[1]0 1 2 3 ... 127
//[2]0 1 2 3 ... 127
//[3]0 1 2 3 ... 127
//[4]0 1 2 3 ... 127
//[5]0 1 2 3 ... 127
//[6]0 1 2 3 ... 127
//[7]0 1 2 3 ... 127
extern SPI_HandleTypeDef hspi1;
void OLED_WR_Byte(unsigned char dat,unsigned char cmd)
{
if(cmd)
OLED_DC_Set();
else
OLED_DC_Clr();
HAL_SPI_Transmit(&hspi1,&dat, 1, 0x00FF);
OLED_DC_Set();
}
void OLED_Set_Pos(unsigned char x, unsigned char y)
{
OLED_WR_Byte(0xb0+y,OLED_CMD);
OLED_WR_Byte(((x&0xf0)>>4)|0x10,OLED_CMD);
OLED_WR_Byte((x&0x0f)|0x01,OLED_CMD);
}
//开始OLED显示
void OLED_Display_On(void)
{
OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令
OLED_WR_Byte(0X14,OLED_CMD); //DCDC ON
OLED_WR_Byte(0XAF,OLED_CMD); //DISPLAY ON
}
//关闭OLED显示
void OLED_Display_Off(void)
{
OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令
OLED_WR_Byte(0X10,OLED_CMD); //DCDC OFF
OLED_WR_Byte(0XAE,OLED_CMD); //DISPLAY OFF
}
//清屏函数(屏幕全黑)
void OLED_Clear(void)
{
unsigned char i,n;
for(i=0;i<8;i++)
{
OLED_WR_Byte (0xb0+i,OLED_CMD); //设置页地址(0~7)
OLED_WR_Byte (0x00,OLED_CMD); //设置显示位置-列低地址
OLED_WR_Byte (0x10,OLED_CMD); //设置显示位置-列高地址
for(n=0;n<128;n++)OLED_WR_Byte(0,OLED_DATA);
} //更新显示
}
//指定位置显示一个字符,包括部分字符
//x:0~127
//y:0~63
//mode:0,反白显示;1,正常显示
//size:选择字体 16/12
void OLED_ShowChar(unsigned char x,unsigned char y,unsigned char chr)
{
unsigned char c=0,i=0;
c=chr-' ';//得到偏移后的值
if(x>Max_Column-1){x=0;y=y+2;}
if(SIZE ==16)
{
OLED_Set_Pos(x,y);
for(i=0;i<8;i++)
OLED_WR_Byte(F8X16[c*16+i],OLED_DATA);
OLED_Set_Pos(x,y+1);
for(i=0;i<8;i++)
OLED_WR_Byte(F8X16[c*16+i+8],OLED_DATA);
}
else {
OLED_Set_Pos(x,y+1);
for(i=0;i<6;i++)
OLED_WR_Byte(F6x8[c][i],OLED_DATA);
}
}
//m^n函数
unsigned int oled_pow(unsigned char m,unsigned char n)
{
unsigned int result=1;
while(n--)result*=m;
return result;
}
//显示2个数字
//x,y :起点坐标
//len :数字的位数
//size:字体大小
//mode:模式0,填充模式;1,叠加模式
//num:数值(0~4294967295);
void OLED_ShowNum(unsigned char x,unsigned char y,unsigned int num,unsigned char len,unsigned char size)
{
unsigned char t,temp;
unsigned char enshow=0;
for(t=0;t<len;t++)
{
temp=(num/oled_pow(10,len-t-1))%10;
if(enshow==0&&t<(len-1))
{
if(temp==0)
{
OLED_ShowChar(x+(size/2)*t,y,' ');
continue;
}else enshow=1;
}
OLED_ShowChar(x+(size/2)*t,y,temp+'0');
}
}
//显示一个字符号串
void OLED_ShowString(unsigned char x,unsigned char y,unsigned char *chr)
{
unsigned char j=0;
while (chr[j]!='\0')
{ OLED_ShowChar(x,y,chr[j]);
x+=8;
if(x>120){x=0;y+=2;}
j++;
}
}
//显示汉字
void OLED_ShowCHinese(unsigned char x,unsigned char y,unsigned char no)
{
unsigned char t,adder=0;
OLED_Set_Pos(x,y);
for(t=0;t<16;t++)
{
OLED_WR_Byte(Hzk[2*no][t],OLED_DATA);
adder+=1;
}
OLED_Set_Pos(x,y+1);
for(t=0;t<16;t++)
{
OLED_WR_Byte(Hzk[2*no+1][t],OLED_DATA);
adder+=1;
}
}
/***********功能描述:显示显示BMP图片128×64起始点坐标(x,y),x的范围0~127,y为页的范围0~7*****************/
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
{
unsigned int j=0;
unsigned char x,y;
if(y1%8==0) y=y1/8;
else y=y1/8+1;
for(y=y0;y<y1;y++)
{
OLED_Set_Pos(x0,y);
for(x=x0;x<x1;x++)
{
OLED_WR_Byte(BMP[j++],OLED_DATA);
}
}
}
//初始化SSD1306
void OLED_Init(void)
{
// MX_GPIO_Init();
// MX_SPI1_Init();
OLED_RST_Set();
HAL_Delay(100);
OLED_RST_Clr();
HAL_Delay(200);
OLED_RST_Set();
OLED_WR_Byte(0xAE,OLED_CMD);//--turn off oled panel
OLED_WR_Byte(0x00,OLED_CMD);//---set low column address
OLED_WR_Byte(0x10,OLED_CMD);//---set high column address
OLED_WR_Byte(0x40,OLED_CMD);//--set start line address Set Mapping RAM Display Start Line (0x00~0x3F)
OLED_WR_Byte(0x81,OLED_CMD);//--set contrast control register
OLED_WR_Byte(0xCF,OLED_CMD); // Set SEG Output Current Brightness
OLED_WR_Byte(0xA1,OLED_CMD);//--Set SEG/Column Mapping 0xa0左右反置 0xa1正常
OLED_WR_Byte(0xC8,OLED_CMD);//Set COM/Row Scan Direction 0xc0上下反置 0xc8正常
OLED_WR_Byte(0xA6,OLED_CMD);//--set normal display
OLED_WR_Byte(0xA8,OLED_CMD);//--set multiplex ratio(1 to 64)
OLED_WR_Byte(0x3f,OLED_CMD);//--1/64 duty
OLED_WR_Byte(0xD3,OLED_CMD);//-set display offset Shift Mapping RAM Counter (0x00~0x3F)
OLED_WR_Byte(0x00,OLED_CMD);//-not offset
OLED_WR_Byte(0xd5,OLED_CMD);//--set display clock divide ratio/oscillator frequency
OLED_WR_Byte(0x80,OLED_CMD);//--set divide ratio, Set Clock as 100 Frames/Sec
OLED_WR_Byte(0xD9,OLED_CMD);//--set pre-charge period
OLED_WR_Byte(0xF1,OLED_CMD);//Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
OLED_WR_Byte(0xDA,OLED_CMD);//--set com pins hardware configuration
OLED_WR_Byte(0x12,OLED_CMD);
OLED_WR_Byte(0xDB,OLED_CMD);//--set vcomh
OLED_WR_Byte(0x40,OLED_CMD);//Set VCOM Deselect Level
OLED_WR_Byte(0x20,OLED_CMD);//-Set Page Addressing Mode (0x00/0x01/0x02)
OLED_WR_Byte(0x02,OLED_CMD);//
OLED_WR_Byte(0x8D,OLED_CMD);//--set Charge Pump enable/disable
OLED_WR_Byte(0x14,OLED_CMD);//--set(0x10) disable
OLED_WR_Byte(0xA4,OLED_CMD);// Disable Entire Display On (0xa4/0xa5)
OLED_WR_Byte(0xA6,OLED_CMD);// Disable Inverse Display On (0xa6/a7)
OLED_WR_Byte(0xAF,OLED_CMD);//--turn on oled panel
OLED_WR_Byte(0xAF,OLED_CMD); /*display ON*/
OLED_Clear();
OLED_Set_Pos(0,0);
}
//显示数据函数
void TEST_MainPage(void)
{
OLED_ShowString(0,3,"CHRISTIAN");
HAL_Delay(1500);
HAL_Delay(1500);
}
2.oled.h
#ifndef __OLED_H
#define __OLED_H
#include "main.h"
#include "stdlib.h"
//OLED模式设置
//0:4线串行模式
//1:并行8080模式
#define OLED_MODE 0
#define SIZE 16
#define XLevelL 0x00
#define XLevelH 0x10
#define Max_Column 128
#define Max_Row 64
#define Brightness 0xFF
#define X_WIDTH 128
#define Y_WIDTH 64
//-----------------OLED端口定义----------------
#define OLED_RST_Clr() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_RESET)//RES
#define OLED_RST_Set() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_SET)
#define OLED_DC_Clr() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_RESET)//DC
#define OLED_DC_Set() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_SET)
#define OLED_CMD 0 //写命令
#define OLED_DATA 1 //写数据
此处删去原来有关SCL、SDA与CS的 清0、置1 定义,并将原来的函数替换为HAL函数。
3.oledfont.h
显示的OLED内容-——数字,汉字,图片等(附:字模软件下载传送门)
4.OLED滚屏函数
1、水平(左右移)
OLED_WR_Byte(0x2E,OLED_CMD); //关闭滚动
OLED_WR_Byte(0x26,OLED_CMD); //水平向左或者右滚动 26/27
OLED_WR_Byte(0x00,OLED_CMD); //虚拟字节
OLED_WR_Byte(0x00,OLED_CMD); //起始页 0
OLED_WR_Byte(0x07,OLED_CMD); //滚动时间间隔
OLED_WR_Byte(0x07,OLED_CMD); //终止页 7
OLED_WR_Byte(0x00,OLED_CMD); //虚拟字节
OLED_WR_Byte(0xFF,OLED_CMD); //虚拟字节
OLED_WR_Byte(0x2F,OLED_CMD); //开启滚动
2、斜着滚动(垂直+水平)
OLED_WR_Byte(0x2e,OLED_CMD); //关闭滚动
OLED_WR_Byte(0x29,OLED_CMD); //水平垂直和水平滚动左右 29/2a
OLED_WR_Byte(0x00,OLED_CMD); //虚拟字节
OLED_WR_Byte(0x00,OLED_CMD); //起始页 0
OLED_WR_Byte(0x07,OLED_CMD); //滚动时间间隔
OLED_WR_Byte(0x07,OLED_CMD); //终止页 1
OLED_WR_Byte(0x01,OLED_CMD); //垂直滚动偏移量
OLED_WR_Byte(0x2F,OLED_CMD); //开启滚动
说明:设置前需要先发关闭滚动的指令2E,接着发滚动指令29(向右)或2A(向左)。紧接着发5条参数设置指令,用来设置持续水平滚动参数和决定滚动开始页,结束页,滚动速度和垂直滚动偏移的,最后才发开始滚屏指令2F。
注意:在发送开始滚屏(2F)前要先传输好显示数据。(此文出处)
5.OLED显示数据
定义数组string[10]。
sprintf((char *)string,"%f V ",ADC_ConvertedValueLocal);
OLED_ShowString(0,2,string);
三、成果展示
四、部分疑问
目前本人的OLED初始化函数无初始化GPIO,是否需要?对指南者进行程序移植时stlink的debug出问题了?…
------------------------------------------------------------问题分割线------------------------------------------------------------
1、答:基于CubeMX的情况下,不再需要初始化GPIO。因为在main.c中已经有相关GPIO初始函数。
2、答:纯属于本人的粗心大意,在CubeMX设置中没有对Debug一项进行选择,导致后来折腾了好久。所幸是,后来的使用中都不会忘记这个教训。
五、附件下载
1、CubeMX版
2、库函数版
小总结
最近学习效率很低,要想办法更加专注在学习上。希望以后学习能以这种方式进行…