linux开发 | tftp下载内核及nfs挂载根文件系统启动log2

U-Boot 1.3.4 (Aug  5 2021 - 08:18:54) for x210@Flyer


CPU:  S5PV210@1000MHz(OK)
        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
        MPLL = 667MHz, EPLL = 96MHz
                       HclkDsys = 166MHz, PclkDsys = 83MHz
                       HclkPsys = 133MHz, PclkPsys = 66MHz
                       SCLKA2M  = 200MHz
Serial = CLKUART
Board:   X210BV3S
DRAM:    512 MB
Flash:   8 MB
SD/MMC:  3728MB
In:      serial
Out:     serial
Err:     serial
[LEFT UP] boot mode
checking mode for fastboot ...
Hit any key to stop autoboot:  0
x210 #
x210 #
x210 #
x210 # setenv bootargs 'root=/dev/nfs nfsroot=192.168.1.104:/opt/v210_rootfs ip=192.168.1.188:192.168.1.104:192.168.1.253:255.255.255.0::eth0:off  init=/linuxrc console=ttySAC2,115200'
x210 # saveenv
Saving Environment to SMDK bootable device...
done
x210 # reset
reset...

OK

U-Boot 1.3.4 (Aug  5 2021 - 08:18:54) for x210@Flyer


CPU:  S5PV210@1000MHz(OK)
        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
        MPLL = 667MHz, EPLL = 96MHz
                       HclkDsys = 166MHz, PclkDsys = 83MHz
                       HclkPsys = 133MHz, PclkPsys = 66MHz
                       SCLKA2M  = 200MHz
Serial = CLKUART
Board:   X210BV3S
DRAM:    512 MB
Flash:   8 MB
SD/MMC:  3728MB
In:      serial
Out:     serial
Err:     serial
[LEFT UP] boot mode
checking mode for fastboot ...
Hit any key to stop autoboot:  0
dm9000 i/o: 0x88000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
TFTP from server 192.168.1.104; our IP address is 192.168.1.188
Filename 'zImage'.
Load address: 0x30008000
Loading: ###########T ######################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ########transmission timeout
T #########################################################
         #################################################################
         #################################################################
         ##
done
Bytes transferred = 3669940 (0x37ffb4)
Boot with zImage

Starting kernel ...



Hello, world 0.@Flyer

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.35.7+ (fly@fly-vm) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 PREEMPT Tue Aug 10 00:00:34 CST 2021
[    0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: SMDKV210
[    0.000000] @@@@@@@ atags_pointer not null
[    0.000000] @@@@@@@linter#####boot_params:c0000100,mdesc->boot_params:40000002
[    0.000000] Ignoring unrecognised tag 0x41001099
[    0.000000] $$$$$$$$$cmdline:root=/dev/nfs nfsroot=192.168.1.104:/opt/v210_rootfs ip=192.168.1.188:192.168.1.104:192.168.1.253:255.255.255.0::eth0:off  init=/linuxrc console=ttySAC2,115200
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S5PV210/S5PC110 (id 0x43110220)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=96000000 V=54000000
[    0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
[    0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
[    0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_onenand: source is hclk_psys (0), rate is 66700000
[    0.000000] sclk: source is mout_mpll (6), rate is 66700000
[    0.000000] sclk: source is mout_mpll (6), rate is 66700000
[    0.000000] sclk: source is mout_mpll (6), rate is 66700000
[    0.000000] sclk: source is mout_mpll (6), rate is 66700000
[    0.000000] sclk_mixer: source is sclk_dac (0), rate is 24000000
[    0.000000] sclk_spdif: source is sclk_audio (0), rate is 24000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_cam0: source is xusbxti (1), rate is 12000000
[    0.000000] sclk_cam1: source is ext_xtal (0), rate is 12000000
[    0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 96000000
[    0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[    0.000000] sclk_mmc: source is mout_epll (7), rate is 96000000
[    0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000
[    0.000000] sclk: source is sclk_a2m (0), rate is 100000000
[    0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_mdnie: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000
[    0.000000] s5pv210: 37748736 bytes system memory reserved for mfc at 0x30c0a000
[    0.000000] s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000
[    0.000000] s5pv210: 25165824 bytes system memory reserved for fimc0 at 0x42400000
[    0.000000] s5pv210: 10137600 bytes system memory reserved for fimc1 at 0x43c00000
[    0.000000] s5pv210: 25165824 bytes system memory reserved for fimc2 at 0x445ab000
[    0.000000] s5pv210: 25165824 bytes system memory reserved for jpeg at 0x45dab000
[    0.000000] s5pv210: 4915200 bytes system memory reserved for fimd at 0x475ab000
[    0.000000] s5pv210: 10485760 bytes system memory reserved for texstream at 0x47a5b000
[    0.000000] s5pv210: 3379200 bytes system memory reserved for pmem_gpu1 at 0x4845b000
[    0.000000] s5pv210: 8388608 bytes system memory reserved for g2d at 0x48794000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: root=/dev/nfs nfsroot=192.168.1.104:/opt/v210_rootfs ip=192.168.1.188:192.168.1.104:192.168.1.253:255.255.255.0::eth0:off  init=/linuxrc console=ttySAC2,115200
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 327696k/327696k available, 196592k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff000000 - 0xffe00000   (  14 MB)
[    0.000000]     vmalloc : 0xe0800000 - 0xfc000000   ( 440 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0033000   ( 172 kB)
[    0.000000]       .text : 0xc0033000 - 0xc06ef000   (6896 kB)
[    0.000000]       .data : 0xc06f0000 - 0xc073d600   ( 310 kB)
[    0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:393
[    0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[    0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[    0.000000] mult[140737]
[    0.000000] max_delta_ns[2937815369]
[    0.000000] min_delta_ns[30517]
[    0.000000] rate[32768]
[    0.000000] HZ[256]
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC2] enabled
[    0.520068] Calibrating delay loop... 998.15 BogoMIPS (lpj=1949696)
[    0.606613] pid_max: default: 32768 minimum: 301
[    0.611263] Mount-cache hash table entries: 512
[    0.615992] Initializing cgroup subsys debug
[    0.619971] Initializing cgroup subsys cpuacct
[    0.624385] Initializing cgroup subsys freezer
[    0.628826] CPU: Testing write buffer coherency: ok
[    0.635608] regulator: core version 0.5
[    0.638095] NET: Registered protocol family 16
[    0.647719] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.652515] pmstats at 00000000
[    0.655640] Open OV2655 camema sensor
[    0.792990] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.799099] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.806634] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.814173] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[    0.821719] smdkv210_nand_io_init
[    0.825378] S5PV210: Initializing architecture
[    0.829718] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[    0.837849] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
[    0.846251] s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000, tin=divclk, base 12
[    0.854743] s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000, tin=divclk, base 16
[    0.863352] regulator: pd_audio_supply: 5000 mV normal
[    0.868513] regulator: pd_cam_supply: 5000 mV normal
[    0.873526] regulator: pd_tv_supply: 5000 mV normal
[    0.878459] regulator: pd_lcd_supply: 5000 mV normal
[    0.883487] regulator: pd_g3d_supply: 5000 mV normal
[    0.888512] regulator: pd_mfc_supply: 5000 mV normal
[    0.899381] bio: create slab <bio-0> at 0
[    0.902472] SCSI subsystem initialized
[    0.905762] usbcore: registered new interface driver usbfs
[    0.911162] usbcore: registered new interface driver hub
[    0.916479] usbcore: registered new device driver usb
[    0.921812] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[    0.927028] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[    0.932335] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[    0.937836] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.944241] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[    0.951368] cfg80211: Calling CRDA to update world regulatory domain
[    0.957657] Switching to clocksource clock_source_systimer
[    0.968032] NET: Registered protocol family 2
[    0.971099] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.978518] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.985332] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[    0.992072] TCP: Hash tables configured (established 16384 bind 16384)
[    0.998125] TCP reno registered
[    1.001235] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    1.007156] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    1.013597] NET: Registered protocol family 1
[    1.018029] RPC: Registered udp transport module.
[    1.022479] RPC: Registered tcp transport module.
[    1.027153] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.033714] PMU: registered new PMU device of type 0
[    1.038542] wifi power management
[    1.042032] SMDKC110/V210 RTC, (c) 2010 Samsung Electronics
[    1.047473] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[    1.053549] smdkc110-rtc smdkc110-rtc: rtc core: registered s3c as rtc0
[    1.060047] S5PV210 ADC driver, (c) 2010 Samsung Electronics
[    1.065833] cpuidle: phy_regs_save:0x4fd7c000
[    1.070264] input: s3c-button as /devices/virtual/input/input0
[    1.075782] s3c button Initialized!!
[    1.079446] Loaded driver for PL330 DMAC-0 s3c-pl330
[    1.084273]  DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[    1.090395] Loaded driver for PL330 DMAC-1 s3c-pl330
[    1.095275]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.101414] Loaded driver for PL330 DMAC-2 s3c-pl330
[    1.106275]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.119119] ashmem: initialized
[    1.121382] NTFS driver 2.1.29 [Flags: R/W].
[    1.125071] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.132093] ROMFS MTD (C) 2007 Red Hat, Inc.
[    1.136270] msgmni has been set to 640
[    1.142458] alg: No test for stdrng (krng)
[    1.145137] io scheduler noop registered
[    1.149022] io scheduler deadline registered
[    1.153243] io scheduler cfq registered (default)
[    1.158590] s3cfb s3cfb: [fb2] dma: 0x475ab000, cpu: 0xe1000000, size: 0x004b0000
[    1.169355] FIMD src sclk = 166750000
[    1.171591] s3cfb s3cfb: registered successfully
[    1.176145] Start display and show logo
[    1.280728] x210 led driver
[    1.348740] PA FB = 0x475AB000, bits per pixel = 32
[    1.352180] screen width=1024 height=600 va=0xd75ab000 pa=0x475ab000
[    1.358489] xres_virtual = 1024, yres_virtual = 1200, xoffset = 0, yoffset = 0
[    1.365674] fb_size=4915200
[    1.368432] Back frameBuffer[0].VAddr=d7803000 PAddr=47803000 size=2457600
[    1.375626] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[    1.383771] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[    1.391818] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[    1.399946] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[    1.412297] brd: module loaded
[    1.416066] loop: module loaded
[    1.417816] pmem_gpu1: 1 init
[    1.421116] Android kernel panic handler initialized (bind=kpanic)
[    1.427305] S3C NAND Driver, (c) 2008 Samsung Electronics
[    1.432333] Unknown NAND Device.
[    1.435471] PPP generic driver version 2.4.2
[    1.439877] PPP Deflate Compression module registered
[    1.444697] PPP BSD Compression module registered
[    1.450101] PPP MPPE Compression module registered
[    1.454147] NET: Registered protocol family 24
[    1.460134] dm9000 Ethernet Driver, V1.31
[    1.463958] eth0: dm9000c at e08f4300,e08f8304 IRQ 42 MAC: 00:09:c0:ff:ec:48 (platform data)
[    1.471151] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.477709] s5p-ehci s5p-ehci: s5pv210 EHCI
[    1.481773] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    1.488845] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[    1.502079] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[    1.506070] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.512769] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.519962] usb usb1: Product: s5pv210 EHCI
[    1.524112] usb usb1: Manufacturer: Linux 2.6.35.7+ ehci_hcd
[    1.529749] usb usb1: SerialNumber: s5pv210
[    1.534341] hub 1-0:1.0: USB hub found
[    1.537658] hub 1-0:1.0: 1 port detected
[    1.541718] Initializing USB Mass Storage driver...
[    1.546482] usbcore: registered new interface driver usb-storage
[    1.552365] USB Mass Storage support registered.
[    1.557210] mice: PS/2 mouse device common for all mice
[    1.562475] S5P Touchscreen driver, (c) 2008 Samsung Electronics
[    1.568235] s3c-ts s3c-ts: Created Median filter len:5 coords:2 dec_threshold:6
[    1.575432] s3c-ts s3c-ts: Created Mean filter len:3 coords:2
[    1.581177] s3c-ts s3c-ts: Created Linear filter coords:2
[    1.586519] s3c-ts s3c-ts: Created zoom filter coords:2
[    1.591711] s3c-ts s3c-ts: 4 filter(s) initialized
[    1.596502] S5P TouchScreen got loaded successfully : 12 bits
[    1.602355] input: S5P TouchScreen as /devices/virtual/input/input1
[    1.608783] [GSLX680] Enter gslX680_ts_init
[    1.612829] input: gslX680 as /devices/platform/s3c2440-i2c.1/i2c-1/1-0040/input/input2
[    1.881002] usb 1-1: new high speed USB device using s5p-ehci and address 2
[    2.015317] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    2.020557] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.027661] usb 1-1: Product: USB2.0 Hub
[    2.032176] hub 1-1:1.0: USB hub found
[    2.035571] hub 1-1:1.0: 4 ports detected
[    4.253339] using rtc device, s3c, for alarms
[    4.256223] i2c /dev entries driver
[    4.260165] Linux video capture interface: v2.00
[    4.264361] gspca: main v2.9.0 registered
[    4.268412] s3c-csis: Samsung MIPI-CSI2 driver probed successfully
[    4.274475] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[    4.274481]
[    4.283065] S3C JPEG Driver, (c) 2007 Samsung Electronics
[    4.288044] JPEG driver for S5PV210
[    4.292105] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[    4.297954] S5PC11X HPD Driver, (c) 2009 Samsung Electronics
[    4.303745] S5PC11X CEC Driver, (c) 2009 Samsung Electronics
[    4.309675] usbcore: registered new interface driver uvcvideo
[    4.314900] USB Video Class driver (v0.1.0)
[    4.321707] device-mapper: uevent: version 1.0.3
[    4.327617] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[    4.334676] cpuidle: using governor ladder
[    4.338730] cpuidle: using governor menu
[    4.342601] sdhci: Secure Digital Host Controller Interface driver
[    4.348709] sdhci: Copyright(c) Pierre Ossman
[    4.353287] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[    4.359645] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
[    4.366231] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[    4.373175] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    4.380045] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[    4.386596] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz)
[    4.393178] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[    4.470398] wifi power enabled
[    4.472082] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[    4.479054] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[    4.485599] s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)
[    4.492195] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[    4.499057] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[    4.506004] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[    4.512553] s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)
[    4.519141] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[    4.526016] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[    4.533604] usbcore: registered new interface driver hiddev
[    4.538527] usbcore: registered new interface driver usbhid
[    4.544000] usbhid: USB HID core driver
[    4.548384] logger: created 64K log 'log_main'
[    4.552368] logger: created 256K log 'log_events'
[    4.557038] logger: created 64K log 'log_radio'
[    4.561536] logger: created 64K log 'log_system'
[    4.568218] No device for DAI WM8976 HiFi
[    4.570800] s3c64xx_iis_dai_init:s3c64xx-i2s0
[    4.575310] s3c64xx_iis_dev_probe:id0 !!!
[    4.579184] s3c64xx_iis_dai_init:s3c64xx-i2s1
[    4.583850] WM8976 Audio Codec 0.4wm8976_probe: i2c_master_send
[    4.589619] wm8976_init
[    4.629636] mmc0: new high speed MMC card at address 0001
[    4.633783] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB
[    4.638293]  mmcblk0: p1 p2 p3 p4
[    5.303222] mmc2: new high speed SDHC card at address aaaa
[    5.307436] mmcblk1: mmc2:aaaa SS08G 7.40 GiB
[    5.311843]  mmcblk1: p1
[    5.367101] s3c_idma_preallocate_buffer:  VA-e0940000  PA-C0000000  163840bytes
[    5.373217] s3c_preallocate_dma_buffer: VA-ff007000, PA-4FF40000, 131072bytes
[    5.380044] asoc: WM8976 HiFi <-> s3c64xx-i2s0 mapping ok
[    5.388744] ALSA device list:
[    5.390259]   #0: smdkc1000 (WM8976)
[    5.393833] GACT probability NOT on
[    5.397274] Mirror/redirect action on
[    5.400911] u32 classifier
[    5.403577]     Actions configured
[    5.406972] Netfilter messages via NETLINK v0.30.
[    5.411714] nf_conntrack version 0.5.0 (5120 buckets, 20480 max)
[    5.417785] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    5.425127] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    5.432890] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    5.439683] ctnetlink v0.93: registering with nfnetlink.
[    5.444430] xt_time: kernel timezone is -0000
[    5.450736] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.454668] arp_tables: (C) 2002 David S. Miller
[    5.459234] TCP cubic registered
[    5.462385] NET: Registered protocol family 10
[    5.468602] lo: Disabled Privacy Extensions
[    5.475981] Mobile IPv6
[    5.476942] IPv6 over IPv4 tunneling driver
[    5.482673] sit0: Disabled Privacy Extensions
[    5.488370] ip6tnl0: Disabled Privacy Extensions
[    5.492872] NET: Registered protocol family 17
[    5.495959] NET: Registered protocol family 15
[    5.500395] lib80211: common routines for IEEE802.11 drivers
[    5.506061] ThumbEE CPU extension supported.
[    5.510340] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[    5.518425] regulator_init_complete: disabling pd_mfc_supply
[    5.523625] regulator_init_complete: disabling pd_tv_supply
[    5.529045] regulator_init_complete: disabling pd_cam_supply
[    5.534722] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[    5.540667] smdkc110-rtc smdkc110-rtc: setting system clock to 2010-01-01 12:03:17 UTC (1262347397)
[    5.551139] FIMC0 registered successfully
[    5.554967] FIMC1 registered successfully
[    5.558938] FIMC2 registered successfully
[    5.561716] <6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[    5.568388] s5p-tvout s5p-tvout: hpd status is cable removed
[    6.119299] eth0: link down
[    6.120764] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.439589] eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
[    6.443788] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.127227] IP-Config: Complete:
[    7.128802]      device=eth0, addr=192.168.1.188, mask=255.255.255.0, gw=192.168.1.253,
[    7.136686]      host=192.168.1.188, domain=, nis-domain=(none),
[    7.142683]      bootserver=192.168.1.104, rootserver=192.168.1.104, rootpath=
[    7.150243] DBUG_PORT must not use AFC!
[    7.153998] Looking up port of RPC 100003/2 on 192.168.1.104
[    7.167938] Looking up port of RPC 100005/1 on 192.168.1.104
[    7.194330] VFS: Mounted root (nfs filesystem) on device 0:12.
[    7.198734] Freeing init memory: 172K
can't run '/etc/init.d/rcS': No such file or directory

Please press Enter to activate this console.
id: unknown ID 0
[@192 ]# ls /etc/init.d/rcS -l
-rwxr-xr-x    1 1000     1000           265 Aug 11  2021 /etc/init.d/rcS
[@192 ]#