Arduino Pulsesensor脉搏心率的检测

开发板与传感器的型号

开发板：Arduino mega 2560

传感器：Pulsesensor脉搏心率传感器，我的模块购买链接https://m.tb.cn/h.fJbXs9y?tk=Wro828Inpfw

传感器来连接到开发板

传感器正极连接到开发板的5V。

传感器负极连接到开发板的GND。

传感器S连接到开发板的A0针脚。

上传代码

/*  Pulse Sensor Amped 1.5    by Joel Murphy and Yury Gitman   http://www.pulsesensor.com

----------------------  Notes ----------------------  ----------------------
This code:
1) Blinks an LED to User's Live Heartbeat   PIN 13
2) Fades an LED to User's Live HeartBeat    PIN 5
3) Determines BPM
4) Prints All of the Above to Serial

Read Me:
https://github.com/WorldFamousElectronics/PulseSensor_Amped_Arduino/blob/master/README.md
 ----------------------       ----------------------  ----------------------
*/

#define PROCESSING_VISUALIZER 1
#define SERIAL_PLOTTER  2

//  Variables
int pulsePin = 0;                 // Pulse Sensor purple wire connected to analog pin 0
int blinkPin = 13;                // pin to blink led at each beat
int fadePin = 5;                  // pin to do fancy classy fading blink at each beat
int fadeRate = 0;                 // used to fade LED on with PWM on fadePin

// Volatile Variables, used in the interrupt service routine!
volatile int BPM;                   // int that holds raw Analog in 0. updated every 2mS
volatile int Signal;                // holds the incoming raw data
volatile int IBI = 600;             // int that holds the time interval between beats! Must be seeded!
volatile boolean Pulse = false;     // "True" when User's live heartbeat is detected. "False" when not a "live beat".
volatile boolean QS = false;        // becomes true when Arduoino finds a beat.

// SET THE SERIAL OUTPUT TYPE TO YOUR NEEDS
// PROCESSING_VISUALIZER works with Pulse Sensor Processing Visualizer
//      https://github.com/WorldFamousElectronics/PulseSensor_Amped_Processing_Visualizer
// SERIAL_PLOTTER outputs sensor data for viewing with the Arduino Serial Plotter
//      run the Serial Plotter at 115200 baud: Tools/Serial Plotter or Command+L
static int outputType = PROCESSING_VISUALIZER;


void setup(){
  pinMode(blinkPin,OUTPUT);         // pin that will blink to your heartbeat!
  pinMode(fadePin,OUTPUT);          // pin that will fade to your heartbeat!
  Serial.begin(115200);             // we agree to talk fast!
  interruptSetup();                 // sets up to read Pulse Sensor signal every 2mS
   // IF YOU ARE POWERING The Pulse Sensor AT VOLTAGE LESS THAN THE BOARD VOLTAGE,
   // UN-COMMENT THE NEXT LINE AND APPLY THAT VOLTAGE TO THE A-REF PIN
//   analogReference(EXTERNAL);
}


//  Where the Magic Happens
void loop(){

    serialOutput() ;

  if (QS == true){     // A Heartbeat Was Found
                       // BPM and IBI have been Determined
                       // Quantified Self "QS" true when arduino finds a heartbeat
        fadeRate = 255;         // Makes the LED Fade Effect Happen
                                // Set 'fadeRate' Variable to 255 to fade LED with pulse
        serialOutputWhenBeatHappens();   // A Beat Happened, Output that to serial.
        QS = false;                      // reset the Quantified Self flag for next time
  }

  ledFadeToBeat();                      // Makes the LED Fade Effect Happen
  delay(20);                             //  take a break
}

void ledFadeToBeat(){
    fadeRate -= 15;                         //  set LED fade value
    fadeRate = constrain(fadeRate,0,255);   //  keep LED fade value from going into negative numbers!
    analogWrite(fadePin,fadeRate);          //  fade LED
  }

显示传感器的数据

这里使用PulseSensor显示程序来显示，简单到没步骤，打开就能用。

PulseSensor显示程序，下载链接：https://pan.baidu.com/s/1bVOTHLK0OdBlTYoLEKzBbA  提取码：1111