1、实验环境
如图8.11所示,三台路由器R1, R2,R3两两互连。R2上配置了Loopback地址192.168.20 .1/24,模拟192.168.20.0/24网段;R3上配置了两个Loopback地址192.168.10.1/24、192.168 .30.1/24.分别用来模拟192.168.10.0/24和192.168.30.0/24网段。
2、需求描述
需要实现当192.168.20.0/24访问192.168.30.0/24时,数据从R2到R3,而当192.168.20.0/24访问192.168.10.0/24时,数据从R2经过R1再到R3,返回的路由都从R3到R2,
3、推荐步骤
在R2上配置到192.168.30.0/24的静态路由。
在R2上配置到192.168.10.0/24的静态路由,在R1上也应该配置到192.168.10.0/24的静态路由。
在 R3上配置回程的静态路由
4、实验步骤
(1)路由器R1上的基础配置
Router>enable
Router#conf t
Router(config)#hostname R1
R1(config)#interface gigabitEthernet 0/3/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#interface gigabitEthernet 0/2/0
R1(config-if)#ip address 192.168.2.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#
(2)路由器R2上的基础配置
Router>en
Router#conf t
Router(config)#hostname R2
R2(config)#interface gigabitEthernet 0/3/0
R2(config-if)#ip address 192.168.1.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface gigabitEthernet 0/0
R2(config-if)#ip address 192.168.20.254 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface gigabitEthernet 0/2/0
R2(config-if)#ip address 192.168.3.2 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#
Router>en
Router#conf t
Router(config)#hostname R3
R3(config)#interface gigabitEthernet 0/3/0
R3(config-if)#ip address 192.168.2.3 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#interface gigabitEthernet 0/2/0
R3(config-if)#ip address 192.168.3.3 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#interface gigabitEthernet 0/0
R3(config-if)#ip address 192.168.10.254 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#interface gigabitEthernet 0/1
R3(config-if)#ip address 192.168.30.254 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#