划分vlan实现跨交换机vlan内通信

使用软件:Cisco Packet Tracer

使用设备:PC机、cisco-2960交换机、cisco-3560-24PS交换机(有路由功能的三层交换机)

 

一、划分vlan

配置接线

按图示连接好八个PC机,三个2960交换机

PC机与交换机之间用实线,交换机之间用虚线

switch0:

        PC0连接f0/1

        PC1连接f0/2

        PC2连接f0/10

        PC3连接f0/11

switch1:

        PC4连接f0/1

        PC5连接f0/2

        PC6连接f0/10

        PC7连接f0/11

依次配置八个PC机的IP地址 

PC0:192.168.1.1
PC1:192.168.1.2
PC2:192.168.1.3
PC3:192.168.1.4
PC4:192.168.1.5
PC5:192.168.1.6
PC6:192.168.1.7
PC7:192.168.1.8

在交换机中进行配置划分vlan域

(所有接口默认均处在vlan1域中)

switch0命令:

Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20//创建两个vlan域
Switch(config-vlan)#int range f0/1-2
Switch(config-if-range)#switchport access vlan 10//将f0/1和f0/2接口划分到vlan10域中
Switch(config-if-range)#int range f0/10-11
Switch(config-if-range)#switchport access vlan 20//将f0/10和f0/11接口划分到vlan20域中
switch1命令:

Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20//创建两个vlan域
Switch(config-vlan)#int range f0/1-2
Switch(config-if-range)#switchport access vlan 10//将f0/1和f0/2接口划分到vlan10域中
Switch(config-if-range)#int range f0/10-11
Switch(config-if-range)#switchport access vlan 20//将f0/10和f0/11接口划分到vlan20域中

这样就将八台PC机划分为四个vlan域了

switch0和switch1下虽然都有vlan10,但是他们由于经过switch2,switch2暂时还没有配置,所有接口依旧处于vlan1域中,所以switch0与switch1两个交换机下的PC机虽然在同一vlan域,但是依旧不可互相通信

二、跨交换机vlan内通信

利用除连接PC机的另外一个交换机实现两个交换机下的PC之间的vlan内通信

其实只配置switch0和switch1就行,但是最好还是配置一下switch2,养成良好习惯,不然域扩大,配置不全,容易出bug

switch0命令:

Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int g0/1
Switch(config-if)#switchport mode trunk
switch1命令:

Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int g0/1
Switch(config-if)#switchport mode trunk
switch2命令:

Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int range f0/1-2
Switch(config-if-range)#switchport mode trunk

    //出现下面情况就是启动了
Switch(config-if-range)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up

测试PC0能否与PC1、PC4、PC5通信(正常情况下应该是可以通信,因为同属vlan10)

测试PC2能否与PC3、PC6、PC7通信(正常情况下应该是可以通信,因为同属vlan20)

三、vlan间主机路由

更换switch2为cisco-3560交换机

3560命令:

Would you like to enter the initial configuration dialog? [yes/no]: no


Press RETURN to get started!



Switch>
Switch>enable
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#^Z
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#ip routing
	//启动路由功能
Switch(config)#int vlan 10
Switch(config-if)#ip address 192.168.1.100 255.255.255.0
	//配置vlan域的网关
Switch(config-if)#no shutdown 
Switch(config-if)#int vlan 20
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

Switch(config-if)#ip address 192.168.2.100 255.255.255.0
Switch(config-if)#no shutdown 

至此,vlan10与vlan20就划分为两个网段了

通信互不干扰

PC0与PC1、PC4、PC5及网关都可以正常通信

PC2与PC3、PC6、PC7及网关都可以正常通信

评论 1
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值