华为无线设备配置频谱导航

1. 配置LAW和AC，使AP与AC之间能够传输CAPWAP报文
   [LSW1]vlan batch 10
   [LSW1-GigabitEthernet0/0/1]port link-type trunk
   [LSW1-GigabitEthernet0/0/1]port trunk allow-pass vlan 10
   [LSW1-GigabitEthernet0/0/2]port link-type trunk
   [LSW1-GigabitEthernet0/0/2]port trunk allow-pass vlan 10
   [LSW1-GigabitEthernet0/0/2]port trunk pvid vlan 10
   [AC1]vlan batch 10 20
   [AC1-GigabitEthernet0/0/1]port link-type trunk
   [AC1-GigabitEthernet0/0/1]port trunk allow-pass vlan 10

2. 配置AC与上层网络设备互通
   [AC1-GigabitEthernet0/0/2]port link-type trunk
   [AC1-GigabitEthernet0/0/2]port trunk allow-pass vlan 20
   [AC1-GigabitEthernet0/0/2]port trunk pvid vlan 20

3. 配置AC作为DHCP服务器，为STA和AP分配IP地址
   [AC1]dhcp enable
   [AC1-Vlanif10]ip add 10.1.1.1 24
   [AC1-Vlanif10]dhcp select interface
   [AC1-Vlanif20]ip add 10.1.2.1 24
   [AC1-Vlanif20]dhcp select interface

4. 配置AP上线
   [AC1]wlan
   [AC1-wlan-view]ap-group name ap-group1 //创建AP组
   [AC1-wlan-view]regulatory-domain-profile name domain1 //创建域管理模板，配置AC的国家码
   [AC1-wlan-regulate-domain-domain1]country-code cn
   [AC1-wlan-view]ap-group name ap-group1 //在AP组下引用域管理模板
   [AC1-wlan-ap-group-ap-group1]regulatory-domain-profile domain1
   [AC1]capwap source interface Vlanif 10 //配置AC的源接口
   [AC1]wlan
   [AC1-wlan-view]ap auth-mode mac-auth
   [AC1-wlan-view]ap-id 0 ap-mac 00e0-fc63-2780 //在AC上离线导入AP
   [AC1-wlan-ap-0]ap-name ap1
   [AC1-wlan-ap-0]ap-group ap-group1 //将AP加入AP组
   

5. 配置WLAN业务参数
   [AC1-wlan-view]security-profile name wlan-security //创建安全模板，并配置安全策略
   [AC1-wlan-sec-prof-wlan-security]security wpa2 psk pass-phrase abc@1234 aes
   [AC1-wlan-view]ssid-profile name wlan-ssid //创建SSID模板，并配置SSID名称
   [AC1-wlan-ssid-prof-wlan-ssid]ssid wlan-net
   [AC1-wlan-view]vap-profile name wlan-vap //创建VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板
   [AC1-wlan-vap-prof-wlan-vap]forward-mode tunnel
   [AC1-wlan-vap-prof-wlan-vap]service-vlan vlan-id 20
   [AC1-wlan-vap-prof-wlan-vap]security-profile wlan-security
   [AC1-wlan-vap-prof-wlan-vap]ssid-profile wlan-ssid
   [AC1-wlan-view]ap-group name ap-group1 //配置AP组引用VAP模板
   [AC1-wlan-ap-group-ap-group1]vap-profile wlan-vap wlan 1 radio all

6. 配置频谱导航功能
   [AC1-wlan-view]rrm-profile name band-steer //创建RRM模板,并配置频谱导航射频间的负载均衡，以免某一频段负载过重。频谱导航射频间负载均衡的起始门限是15个，差值门限是25%
   [AC1-wlan-rrm-prof-band-steer]band-steer balance start-threshold 15
   [AC1-wlan-rrm-prof-band-steer]band-steer balance gap-threshold 25
   [AC1-wlan-view]radio-2g-profile name radio2g //创建2G射频模板,并在该模板下引用RRM模板
   [AC1-wlan-radio-2g-prof-radio2g]rrm-profile band-steer
   [AC1-wlan-view]ap-group name ap-group1 //的AP组下引用2G射频模板
   [AC1-wlan-ap-group-ap-group1]radio-2g-profile radio2g radio all

7. 验证配置