POJ1273——Drainage Ditches（最大流模板题）

用来测试模板的模板题

题目中已经把图建好了，只需要用最大流模板计算一下就可以了

题意：有m个池塘，编号为1-m，1为源点，m为汇点，以及n条水渠，给出1-m的最大流量

对此我不得不吐槽一下刘汝佳书上的版实在是太慢了。。。。。。

Drainage Ditches

Time Limit: 1000MS		Memory Limit: 10000K
Total Submissions: 77671		Accepted: 30255

Description

Every time it rains on Farmer John's fields, a pond forms over Bessie's favorite clover patch. This means that the clover is covered by water for awhile and takes quite a long time to regrow. Thus, Farmer John has built a set of drainage ditches so that Bessie's clover patch is never covered in water. Instead, the water is drained to a nearby stream. Being an ace engineer, Farmer John has also installed regulators at the beginning of each ditch, so he can control at what rate water flows into that ditch. 
Farmer John knows not only how many gallons of water each ditch can transport per minute but also the exact layout of the ditches, which feed out of the pond and into each other and stream in a potentially complex network. 
Given all this information, determine the maximum rate at which water can be transported out of the pond and into the stream. For any given ditch, water flows in only one direction, but there might be a way that water can flow in a circle. 

Input

The input includes several cases. For each case, the first line contains two space-separated integers, N (0 <= N <= 200) and M (2 <= M <= 200). N is the number of ditches that Farmer John has dug. M is the number of intersections points for those ditches. Intersection 1 is the pond. Intersection point M is the stream. Each of the following N lines contains three integers, Si, Ei, and Ci. Si and Ei (1 <= Si, Ei <= M) designate the intersections between which this ditch flows. Water will flow through this ditch from Si to Ei. Ci (0 <= Ci <= 10,000,000) is the maximum rate at which water will flow through the ditch.

Output

For each case, output a single integer, the maximum rate at which water may emptied from the pond.

Sample Input

5 4
1 2 40
1 4 20
2 4 20
2 3 30
3 4 10

Sample Output

50

代码：

#include <iostream>
//#include <bits/stdc++.h>
#include <cstdio>
#include <cstring>
#include <queue>
#include <vector>
using namespace std;

const int maxn=210;
const int INF=0x7fffffff;
struct edge
{
    int to,from,cap,flow;
    edge(int u,int v,int c,int f):from(u),to(v),cap(c),flow(f){}
};

struct Edge
{
    int to,from,cap,flow;
    Edge(int u,int v,int c,int f):from(u),to(v),cap(c),flow(f){}
};

struct Edmonds_karp
{
    int n,m,s,t;
    vector<Edge> edges;
    vector<int> G[maxn];
    bool vis[maxn];
    int cur[maxn];
    int d[maxn];

    void init(int n,int s,int t)
    {
        this->n=n, this->s=s, this->t=t;
        edges.clear();
        for(int i=0;i<n;++i) G[i].clear();
    }

    void add_edge(int from,int to,int cap)
    {
        edges.push_back( Edge(from,to,cap,0) );
        edges.push_back( Edge(to,from,0,0) );
        m=edges.size();
        G[from].push_back(m-2);
        G[to].push_back(m-1);
    }

    bool BFS()
    {
        queue<int> Q;
        memset(vis,0,sizeof(vis));
        vis[s]=true;
        d[s]=0;
        Q.push(s);
        while(!Q.empty())
        {
            int x=Q.front(); Q.pop();
            for(int i=0;i<G[x].size();++i)
            {
                Edge& e=edges[G[x][i]];
                if(!vis[e.to] && e.cap>e.flow)
                {
                    vis[e.to]=true;
                    d[e.to]=d[x]+1;
                    Q.push(e.to);
                }
            }
        }
        return vis[t];
    }

    int DFS(int x,int a)
    {
        if(x==t || a==0) return a;
        int flow=0, f;
        for(int &i=cur[x];i<G[x].size();++i)
        {
            Edge &e=edges[G[x][i]];
            if(d[e.to]==d[x]+1 && (f=DFS(e.to,min(a,e.cap-e.flow) ) )>0)
            {
                e.flow +=f;
                edges[G[x][i]^1].flow -=f;
                flow +=f;
                a -=f;
                if(a==0) break;
            }
        }
        return flow;
    }

    int max_flow()
    {
        int ans=0;
        while(BFS())
        {
            memset(cur,0,sizeof(cur));
            ans +=DFS(s,INF);
        }
        return ans;
    }
}a;
int main()
{
    ios::sync_with_stdio(false);
    int m,n;
    while(cin>>n>>m){
        a.m=m,a.n=n;
        a.init(n,1,m);
        for(int i=0;i<n;i++)
        {
            int u,v,d;
            cin>>u>>v>>d;
            a.add_edge(u,v,d);
        }
        cout<<a.max_flow()<<endl;
    }
    //cout << "Hello world!" << endl;
    return 0;
}