HAL库STM32的LCD的照片显示时钟

最新推荐文章于 2024-08-03 23:59:26 发布
最新推荐文章于 2024-08-03 23:59:26 发布
阅读量2.2k 收藏 16
点赞数 3
分类专栏： STM32 HAL 文章标签： stm32 单片机 arm
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/Z_xiao_bai/article/details/121686621
版权
STM32 同时被 2 个专栏收录
1 篇文章 0 订阅
订阅专栏
HAL
1 篇文章 0 订阅
订阅专栏

本工程实现了在显示屏上显示一张照片并在照片上以数码管格式显示当前时间，图片大小为128*128；时间为24小时进制的；使用WIFI串口接收数据FF21:10 可把时间更改为21点10分。

本工程使用的处理芯片为stm32f103rct6，显示屏芯片为ST7735S，WIFI模块为HC-25串口WIFI；
主要流程1显示屏的驱动程序编写，添加GUI显示库、Font.h来实现字符、汉字、图片的显示。
效果图

WIFI模块使用的是广州汇承HC-25串口WIFI模块，通过使用官方给的HC-25助手（app）更改时间。

WIFI模块
下边介绍第一部分代码1用屏幕显示一张照片.
从上而下看代码只看 -> 指的代码

showimage(gImage_1);//主函数中调用此函数即可生成一张照片

const unsigned char gImage_1[32768];
//存储的是生成的照片的数组
void showimage(const unsigned char *p) 
{//显示128*128 图片
  	int i; 
	unsigned char picH,picL;
	Lcd_Clear(WHITE); //清屏 ->1 
	
			Lcd_SetRegion(0,0+1+1,127,127+1+1);
		    for(i=0;i<128*128;i++)
			 {	
			 	picL=*(p+i*2);	//数据低位在前
				picH=*(p+i*2+1);				
				LCD_WriteData_16Bit(picH<<8|picL); 				
			 }	
}
}
//->1全屏清屏函数
void Lcd_Clear(u16 Color)               
{	
   unsigned int i,m;
   Lcd_SetRegion(0,0,X_MAX_PIXEL-1,Y_MAX_PIXEL-1);//->2	
   Lcd_WriteIndex(0x2C);
   for(i=0;i<X_MAX_PIXEL;i++)
    for(m=0;m<Y_MAX_PIXEL;m++)
    {	
	  	LCD_WriteData_16Bit(Color);
    }   
}

//->2设置lcd显示区域，在此区域写点数据自动换行
void Lcd_SetRegion(u16 x_start,u16 y_start,u16 x_end,u16 y_end)
{		
	Lcd_WriteIndex(0x2a);//->3		
	Lcd_WriteData(0x00);
	Lcd_WriteData(x_start+2);
	Lcd_WriteData(0x00);
	Lcd_WriteData(x_end+2);

	Lcd_WriteIndex(0x2b);
	Lcd_WriteData(0x00);
	Lcd_WriteData(y_start+1);
	Lcd_WriteData(0x00);
	Lcd_WriteData(y_end+1);
	
	Lcd_WriteIndex(0x2c);
}	
//->3写一个指令
void Lcd_WriteIndex(u8 Index)
{
   //SPI 写命令时序开始
   LCD_CS_CLR;
   LCD_RS_CLR;
	 SPI_WriteData(Index);//->4
   LCD_CS_SET;
}

//->4向lcd写一个8位的数据
void SPI_WriteData(u8 Data){
	unsigned char i=0;
	for(i=8;i>0;i--)
	{
		if(Data&0x80){
			LCD_SDA_SET; //输出数据
		}	
		else{
		LCD_SDA_CLR;
		} 
      LCD_SCL_CLR;       
      LCD_SCL_SET;
      Data<<=1; 
	}
}

LCD_SDA_SET 就是让对应的数据引脚输出高
LCD_SDA_CLR 就是让对应的数据引脚输出低

//输出数据1和0
#define LCD_SDA_SET	  	do{ HAL_GPIO_WritePin(SDA_GPIO_Port,SDA_Pin,GPIO_PIN_SET);}while(0);
#define LCD_SDA_CLR		do{ HAL_GPIO_WritePin(SDA_GPIO_Port,SDA_Pin,GPIO_PIN_RESET);}while(0);

LCD_SCL_CLR;时钟引脚输出低电平
LCD_SCL_SET;时钟引脚输出高电平

//时钟信号1和0
#define LCD_SCL_SET	  	do{ HAL_GPIO_WritePin(SCl_GPIO_Port,SCl_Pin,GPIO_PIN_SET);}while(0);
#define LCD_SCL_CLR		do{ HAL_GPIO_WritePin(SCl_GPIO_Port,SCl_Pin,GPIO_PIN_RESET);}while(0);

showimage()中调用的函数就只有这个没有介绍了

//向液晶屏写一个16位数据
void LCD_WriteData_16Bit(u16 Data)
{
   LCD_CS_CLR;
   LCD_RS_SET;
	 SPI_WriteData(Data>>8); 	//写入高8位数据
	 SPI_WriteData(Data); 			//写入低8位数据
   LCD_CS_SET; 
}

接下来介绍一下显示数码管数字的代码


//数码管显示 第一个为x轴位置y轴位置 参数3数码管颜色，参数4显示的值
void Gui_DrawFont_Num32(u16 x, u16 y, u16 bc, u16 num)
{
	unsigned char i,j,k,c;
    for(i=0;i<32;i++)
	{
		for(j=0;j<4;j++) 
		{
			c=*(sz32+num*32*4+i*4+j);
			for (k=0;k<8;k++)	
			{	
		    	if(c&(0x80>>k))	Gui_DrawPoint(x+j*8+k,y+i,fc);
			}
		}
	}
}

//数码管字体  %  ℃
const unsigned char sz32[]={
#if USE_ONCHIP_FLASH_FONT
//"0",
0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,0x01,0x80,0x06,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x03,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x01,0x80,0x06,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,
//"1",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x01,0x80,0x00,0x00,0x03,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0x80,0x00,0x00,0x03,0x80,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,
//"2",
0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0xFF,0xF0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x1F,0xE3,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xF8,0x00,0x00,0x1F,0xE0,0x00,0x03,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x1F,0xF0,0x00,0x00,0x3F,0xF8,0x00,0x00,0x3F,0xFC,0x00,0x00,0x1F,0xFE,0x00,
//"3",
0x00,0x00,0x00,0x00,0x03,0xFF,0x80,0x00,0x01,0xFF,0xC0,0x00,0x00,0xFF,0xC0,0x00,0x00,0x7F,0x80,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x7F,0x8C,0x00,0x01,0xFF,0xE0,0x00,0x01,0xFF,0xF0,0x00,0x00,0x7F,0x80,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x18,0x00,0x00,0x7F,0x80,0x00,0x00,0xFF,0xC0,0x00,0x01,0xFF,0xC0,0x00,0x03,0xFF,0x80,0x00,
//"4",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x01,0x00,0x03,0x00,0x03,0x00,0x03,0x80,0x07,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0x1F,0xE3,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xFC,0x00,0x00,0x1F,0xE0,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x00,0x00,
//"5",
0x00,0x00,0x00,0x00,0x00,0x1F,0xFC,0x00,0x00,0x3F,0xF8,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,0x01,0x80,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0x1F,0xE0,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xF8,0x00,0x00,0x1F,0xE0,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x06,0x00,0x00,0x3F,0xE0,0x00,0x00,0x7F,0xF0,0x00,0x00,0xFF,0xF0,0x00,0x01,0xFF,0xE0,0x00,
//"6",
0x00,0x00,0x00,0x00,0x00,0x1F,0xFC,0x00,0x00,0x3F,0xF8,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,0x01,0x80,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0x1F,0xE0,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xFC,0x00,0x00,0x1F,0xE0,0x00,0x03,0x00,0x03,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x01,0x80,0x06,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,
//"7",
0x00,0x00,0x00,0x00,0x07,0xFF,0xE0,0x00,0x03,0xFF,0xC0,0x00,0x01,0xFF,0x88,0x00,0x00,0xFF,0x18,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,
//"8",
0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,0x01,0x80,0x06,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0x1F,0xE3,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xFC,0x00,0x00,0x1F,0xE0,0x00,0x03,0x00,0x03,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x01,0x80,0x06,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,
//"9",
0x00,0x00,0x00,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x1F,0xE0,0x00,0x01,0x80,0x06,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0xC0,0x0F,0x00,0x03,0x1F,0xE3,0x00,0x00,0x7F,0xF8,0x00,0x00,0x7F,0xFC,0x00,0x00,0x1F,0xE0,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x06,0x00,0x00,0x1F,0xE0,0x00,0x00,0x3F,0xF0,0x00,0x00,0x7F,0xF0,0x00,0x00,0xFF,0xE0,0x00,
//".",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
//":",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x0F,0x80,0x00,0x00,0x0F,0x80,0x00,0x00,0x0F,0x80,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x0F,0x80,0x00,0x00,0x0F,0x80,0x00,0x00,0x0F,0x80,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
//"%",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xC0,0x06,0x00,0x0F,0xE0,0x06,0x00,0x00,0x00,0x0C,0x00,0x30,0x18,0x18,0x00,0x30,0x18,0x18,0x00,0x30,0x18,0x30,0x00,0x30,0x18,0x30,0x00,0x30,0x18,0x60,0x00,0x30,0x08,0xC0,0x00,0x07,0xC0,0xC0,0x00,0x0F,0xE0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0xE0,0x00,0x06,0x07,0xC0,0x00,0x06,0x30,0x18,0x00,0x0C,0x30,0x18,0x00,0x0C,0x30,0x18,0x00,0x18,0x30,0x18,0x00,0x30,0x30,0x18,0x00,0x30,0x30,0x18,0x00,0x60,0x00,0x00,0x00,0xC0,0x0F,0xE0,0x00,0xC0,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
//"℃",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0xE0,0x00,0x08,0x87,0xFC,0x00,0x08,0x8E,0x03,0x00,0x08,0x98,0x01,0x80,0x07,0x18,0x00,0x80,0x00,0x30,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x70,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x70,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0x18,0x01,0x00,0x00,0x0C,0x03,0x00,0x00,0x07,0xFC,0x00,0x00,0x01,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
//"-",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xF0,0x00,0x00,0x7F,0xF0,0x00,0x00,0x7F,0xE0,0x00,0x00,0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
#endif
0x00,
};

unsigned char Num[ 16]={0,1,2,3,4,5,6,7,8,9,10,11,12,13,14};
//	0-9显示0-9	10-14显示.  :  % ℃ -

//画一个点
void Gui_DrawPoint(u16 x,u16 y,u16 Data)
{
	Lcd_SetRegion(x,y,x+1,y+1);
	LCD_WriteData_16Bit(Data);
}

剩下的就是串口WIFI的代码
把串口就收到的数据解析出时间并设置。


unsigned char Rx_str1[1]; //接收缓存
unsigned char Rx_Buf[10]; //接收缓存10
unsigned char  Rx_i=0;

//时间
unsigned char shi_z; //时间小时
unsigned char shi_y; 
unsigned char fen_z; //分钟
unsigned char fen_y; 
#define huart1 huart2
//把串口1改为串口2 串口1是用来调试注意回调函数里的USART2的更改
char flag=0;
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart){
if(huart->Instance==USART2){
	//把收到的数据放的一个内存里
		if(Rx_str1[0]=='F'){
			Rx_i=0;	flag=1;
		}	
		if(flag==1){
		Rx_Buf[Rx_i++]=Rx_str1[0];
		if(Rx_i==6){
			Rx_i=0;
			HAL_UART_Transmit(&huart1,Rx_Buf,sizeof(Rx_Buf),1000);	
				char T_i=0;
					shi_z=Rx_Buf[++T_i]; 	shi_y=Rx_Buf[++T_i]; 
					T_i++;//跳过":"
					fen_z=Rx_Buf[++T_i]; fen_y=Rx_Buf[++T_i];
			//把字符转为数字
			shi_z=shi_z-'0';shi_y=shi_y-'0';fen_z=fen_z-'0';fen_y=fen_y-'0';
			HAL_UART_Transmit(&huart1,&shi_z,sizeof(shi_z),1000);	
			HAL_UART_Transmit(&huart1,&shi_y,sizeof(shi_y),1000);	
			HAL_UART_Transmit(&huart1,&fen_z,sizeof(fen_z),1000);	
			HAL_UART_Transmit(&huart1,&fen_y,sizeof(fen_y),1000);	
			j=shi_z*10+shi_y;
			i=fen_z*10+fen_y;
			
			showimage(gImage_1);//图片显示示例	
			Gui_DrawFont_Num32(0,95,shenfense,GRAY0,Num[j/10]);
			Gui_DrawFont_Num32(25,95,shenfense,GRAY0,Num[j%10]);
			Gui_DrawFont_Num32(50,95,RED,GRAY0,Num[11]);  
			Gui_DrawFont_Num32(75,95,shenfense,GRAY0,Num[i/10]);	
			Gui_DrawFont_Num32(100,95,shenfense,GRAY0,Num[i%10]);
			flag=0;			
		}			
		}
	HAL_UART_Receive_IT(&huart1,Rx_str1, 1);	//打开串口1的接收中断如果接受到进入接收中断处理函数
}
}

定时器中的代码


unsigned int  i=0, j=0,t=0;
void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim){
		if(htim->Instance==TIM6){
		 //1s 进入一次中断
			t++;LED_R_T;
		if(t==60){t=0;i++; 
			if(i==60){
			showimage1(gImage_1);	
			Gui_DrawFont_Num32(0,95,shenfense,GRAY0,Num[j/10]);
			Gui_DrawFont_Num32(25,95,shenfense,GRAY0,Num[j%10]);
			Gui_DrawFont_Num32(50,95,RED,GRAY0,Num[11]);  
			Gui_DrawFont_Num32(75,95,shenfense,GRAY0,Num[i/10]);	
			Gui_DrawFont_Num32(100,95,shenfense,GRAY0,Num[i%10]);		
				i=0;j++;
				if(j==24)j=0;
			}
		}
		}
		
	if(htim->Instance==TIM7){
	//100ms 优先级比TIM6低
		LED_B_T;				
	}
	
}
郑玉发
关注
  • 3
    点赞
  • 踩
  • 16
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
专栏目录
STM32CubeMX HAL库 ：RTC时钟
weixin_46129506的博客
11-30 2270
目录一、RTC相关介绍二、新建项目三、代码编写四、编写烧录五、总结参考资料 一、RTC相关介绍 RTC实时时钟简介: STM32的RTC外设,实质是一个掉电后还继续运行的定时器,从定时器的角度来看,相对于通用定时器TIM外设,它的功能十分简单,只有计时功能(也可以触发中断).但是从掉电还能继续运行来看,它是STM32中唯一一个具有这个功能功能的外设.(RTC外设的复杂之处不在于它的定时,而在于它掉电还可以继续运行的特性) 所谓掉电,是指电源Vpp断开的情况下,为了RTC外设掉电可以继续运行,必须给STM32
STM32 HAL库入门--点亮LED
weixin_44064291的博客
06-29 911
stm32 hal库入门学习历程
STM32遥控修改RTC时钟带闹钟
qq_43273210的博客
04-19 1329
实验能够通过遥控器进行时间的修改和，闹钟的修改，到达时间将会响铃两秒钟
stm32在显示屏上显示时钟
07-15
stm32的实时时钟设置，我的使用单片机是stm32f407,用的是电容屏
stm32驱动lcd屏幕FLASH图片显示
07-16
代码通过驱动stm32f103zet6的lcd屏幕来显示flash里面的图片
基于stm32的多功能厨房定时器
zxyupup的博客
05-16 2024
一.具体功能 1) 格式：倒计时显示格式“分:秒”，初始状态显示 00:00，表示 0 分 0 秒 2) 按键：使用 3 个按键设置倒计时时间。K1 键为启动/清零（任何时候按 一次启动倒计时，再按一次清零并回到初始状态）；K2、K3 键调加/减， 可只调整分钟字段，调整范围 01-60（分钟），“秒”字段可不调整，开始 倒计时时，每秒“秒”字段减 1 3) 闹铃：倒计时到 00:00，蜂鸣器发出提醒音（持续 10 秒），在此之前如果 按 K1 键，立即停止蜂鸣 4) 重复：按 K1 清零或倒计时结
基于STM32F103RC刷TFTLCD测试记录
weixin_42071920的博客
05-30 2875
一、硬件环境： 1、主控STM32F103RC（无FSMC，I8080时序软件模拟） 2、TFTLCD，320480，ILI9488 3、SPI-FLASH，W25Q128（存放解码之后的JPEG图片数据） 4、图片320480，每张图片300.02K 二、测试结果： 1、刷屏（单色）耗时53ms 代码如下： #define ILI9488_START_Write_DATA() {ILI948...
STM32F4基于HAL库的LCD显示实验
07-29
STM32F4系列是意法半导体（STMicroelectronics）推出的高性能...通过实践这个实验，开发者不仅能掌握STM32F4系列单片机的HAL库编程，还能了解到LCD显示原理及其实现方法，对于深入理解嵌入式系统的软硬件交互大有裨益。
STM32 cubmex fsmc lcd HAL库
07-25
STM32 CubeMX FSMC LCD HAL库是专为STM32微控制器设计的，用于在FSMC（Flexible Static Memory Controller）接口上驱动LCD显示的一种软件框架。本文将深入解析这个库的相关知识点，包括STM32的CubeMX工具、FSMC接口...
STM32提高篇 （一） - LCD显示各种基础小功能实验
11-11
本代码通过FSMC模块实现： TFT_LCD屏显示，填充颜色 TFT_LCD屏显示，显示字符或字符串 TFT_LCD屏显示，显示中文 TFT_LCD屏显示，显示图片 TFT_LCD屏绘制直线、矩形、圆形 了解整个TFT_LCD驱动框架的实现，以及数据如何从STM32流向屏幕，并显示出来的。 代码测试通过，结合 《stm32专栏》 中的知识点。
IIC_LCD1602 STM32-HAL驱动程序-硬件IIC
11-11
在本文中，我们将深入探讨如何使用STM32F103C8T6微控制器，通过HAL库硬件IIC驱动LCD1602模块，并结合PCF8574扩展I/O芯片。这个主题涵盖了嵌入式系统设计、微控制器编程、硬件接口以及驱动程序开发等关键知识点。 ...
stm32f103驱动0.96寸OLED显示屏，hal库版本
04-11
总之，通过STM32F103的HAL库驱动0.96英寸OLED显示屏，开发者可以充分利用STM32的性能和HAL库的便利性，实现高效且易于维护的嵌入式显示方案。在实际开发过程中，理解OLED的工作原理、掌握HAL库的使用以及灵活运用...
STM32F103驱动1.8寸TFTLCD,8PIN，SPI，ST7735。使用STM32cubeMX配置，HAL库版本
07-17
STM32CubeMX是一款强大的配置工具，它可以帮助开发者快速设置STM32微控制器的外设，并自动生成HAL库代码，简化了驱动开发的过程。 首先，我们从STM32CubeMX开始。在这个项目中，你需要打开STM32CubeMX，选择STM32...
硬件SPI+LCD增强屏幕刷新率
NANA_FZM的博客
05-13 4139
基于STM32F103启动硬件SPI加快LCD刷新率
STM32驱动SPI屏幕
电子第一课，点亮LED；第二课，点亮钽电容；第三课，点亮MOS管
05-17 1706
驱动屏幕必须要用STM32自带的SPI，不然刷新很慢，想要更快的刷新就要用到DMA了，刷新频率非常的快。 单片机做液晶屏显示数据，主要用在要求刷新不高的场合，用作工控数据显示操控，
LCD屏幕
weixin_64207326的博客
07-09 306
目录LCD驱动原理 808时序操作​编辑LCD驱动芯片操作设置x、y的起始和结束坐标​编辑 LCD基本驱动实现 字符显示 FSMC（使用FSMC模拟8080时序，可以提高屏幕的刷新率） FSMC时序模式 FSMC相关寄存器LCD初始化结构体​编辑初始化步骤 FSMC模拟8080时序的接口函数的编写​编辑 硬件连接绘图函数 /
提高LCD屏幕刷新效率
weixin_38743772的博客
02-15 2340
提高LCD屏幕刷新效率
stm32提高LCD显式字符的速度,从打点显式到DMA填充
BigAntHome的博客
10-18 1506
最近在使用裸机的方式绘制LCD显式页面，主要参考中景园LCD的历程，在显式驱动移植成果后，设计了两个页面，页面切换中有肉眼可见的延迟，因此想着能不能提高字符显式的频率。
STM32——外部中断（EXTI）
最新发布
脑壳有点痒，好像要长脑子了！
08-03 881
外部中断（External Interrupt，简称EXTI）是微控制器用于响应外部事件的一种方式，当外部事件发生时（如按键按下、传感器信号变化等），微控制器会暂时停止当前正在执行的程序，转而执行相应的中断服务程序（ISR），处理完中断后再回到原来的程序继续执行。STM32的外部中断是STM32微控制器中一个重要的功能，用于接收和处理来自外部设备的信号或事件，在一定程度上提升了系统的实时性能。STM32的每个GPIO（通用输入输出）端口都支持外部中断功能，这使得STM32能够灵活地处理各种外部事件。
基于stm32的lcd显示实验hal库
05-21
好的，下面是基于STM32的LCD显示实验HAL库的步骤： 1. 首先，连接你的STM32开发板和LCD模块。确保它们之间的连接正确无误。 2. 打开STM32CubeMX，创建一个新项目，选择你的开发板型号。 3. 在“Pinout”选项卡中...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值