HCI opcode

HCI控制命令由两个字节的OpCode定义，每个OpCode由一个字节的OGF（OpCode Group Field）和一个字节的OCF（OpCode Command Field）组成。参考：

HCI Command Packet

Command的数据包格式如下图：

其中opcode（操作码）由ogf（opcode group field，6个bits）和ocf（opcode command field，10个bits）组成。

十六进组高低位组合后的opcode为：OGF 6个bit后添加两个0，并移到高8位 + OCF：

以reset命令为例，OGF=0X03,0GF=0X03：

opcode = 0X03为高8位，末尾添加两个0，+OCF = 0x0c03

OGF包括如下定义：

#def ine OGF LINK CONTROL 0 x01
#def ine OGF LINK POLICY 0 x02
#def ine OGF CONTROLLER BASEBAND 0 x03
#def ine OGF INFORMATIONAL PARAMETERS 0 x04
#def ine OGF LE CONTROLLER 0 x08
#def ine OGF BTSTACK 0x3d
#def ine OGF VENDOR 0 x 3f

OCF包括如下定义：

Bluetooth Specififica�tion - Core Version 4.0, Volume 2, Part E, Chapter 7.
// calculate hci opcode for ogf/ocf value
#define HCI_OPCODE(ogf, ocf) ((ocf) | ((ogf) << 10))

// Link Control    HCI_OPCODE_HCI_INQUIRY = HCI_OPCODE (OGF_LINK_CONTROL, 0x01),    HCI_OPCODE_HCI_INQUIRY_CANCEL = HCI_OPCODE (OGF_LINK_CONTROL, 0x02),    HCI_OPCODE_HCI_PERIODIC_INQUIRY_MODE = HCI_OPCODE(OGF_LINK_CONTROL, 0x03),    HCI_OPCODE_HCI_EXIT_PERIODIC_INQUIRY_MODE = HCI_OPCODE(OGF_LINK_CONTROL, 0x04),    HCI_OPCODE_HCI_CREATE_CONNECTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x05),   
HCI_OPCODE_HCI_DISCONNECT = HCI_OPCODE (OGF_LINK_CONTROL, 0x06),    HCI_OPCODE_HCI_CREATE_CONNECTION_CANCEL = HCI_OPCODE (OGF_LINK_CONTROL, 0x08),    HCI_OPCODE_HCI_ACCEPT_CONNECTION_REQUEST = HCI_OPCODE (OGF_LINK_CONTROL, 0x09),    HCI_OPCODE_HCI_REJECT_CONNECTION_REQUEST = HCI_OPCODE (OGF_LINK_CONTROL, 0x0a),    HCI_OPCODE_HCI_LINK_KEY_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x0b),    HCI_OPCODE_HCI_LINK_KEY_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x0c),    HCI_OPCODE_HCI_PIN_CODE_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x0d),    HCI_OPCODE_HCI_PIN_CODE_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x0e),    HCI_OPCODE_HCI_CHANGE_CONNECTION_PACKET_TYPE = HCI_OPCODE (OGF_LINK_CONTROL, 0x0f),    HCI_OPCODE_HCI_AUTHENTICATION_REQUESTED = HCI_OPCODE (OGF_LINK_CONTROL, 0x11),    HCI_OPCODE_HCI_SET_CONNECTION_ENCRYPTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x13),    HCI_OPCODE_HCI_CHANGE_CONNECTION_LINK_KEY = HCI_OPCODE (OGF_LINK_CONTROL, 0x15),    HCI_OPCODE_HCI_REMOTE_NAME_REQUEST = HCI_OPCODE (OGF_LINK_CONTROL, 0x19),    HCI_OPCODE_HCI_REMOTE_NAME_REQUEST_CANCEL = HCI_OPCODE (OGF_LINK_CONTROL, 0x1A),    HCI_OPCODE_HCI_READ_REMOTE_SUPPORTED_FEATURES_COMMAND = HCI_OPCODE (OGF_LINK_CONTROL, 0x1B),    HCI_OPCODE_HCI_READ_REMOTE_EXTENDED_FEATURES_COMMAND = HCI_OPCODE (OGF_LINK_CONTROL, 0x1C),    HCI_OPCODE_HCI_READ_REMOTE_VERSION_INFORMATION = HCI_OPCODE (OGF_LINK_CONTROL, 0x1D),    HCI_OPCODE_HCI_SETUP_SYNCHRONOUS_CONNECTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x0028),    HCI_OPCODE_HCI_ACCEPT_SYNCHRONOUS_CONNECTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x0029),    HCI_OPCODE_HCI_IO_CAPABILITY_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x2b),    HCI_OPCODE_HCI_USER_CONFIRMATION_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x2c),    HCI_OPCODE_HCI_USER_CONFIRMATION_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x2d),    HCI_OPCODE_HCI_USER_PASSKEY_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x2e),    HCI_OPCODE_HCI_USER_PASSKEY_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x2f),    HCI_OPCODE_HCI_REMOTE_OOB_DATA_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x30),    HCI_OPCODE_HCI_REMOTE_OOB_DATA_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x33),    HCI_OPCODE_HCI_IO_CAPABILITY_REQUEST_NEGATIVE_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x34),    HCI_OPCODE_HCI_ENHANCED_SETUP_SYNCHRONOUS_CONNECTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x3d),    HCI_OPCODE_HCI_ENHANCED_ACCEPT_SYNCHRONOUS_CONNECTION = HCI_OPCODE (OGF_LINK_CONTROL, 0x3e),    HCI_OPCODE_HCI_REMOTE_OOB_EXTENDED_DATA_REQUEST_REPLY = HCI_OPCODE (OGF_LINK_CONTROL, 0x45),    // Link Policy   
HCI_OPCODE_HCI_HOLD_MODE = HCI_OPCODE (OGF_LINK_POLICY, 0x01),   
HCI_OPCODE_HCI_SNIFF_MODE = HCI_OPCODE (OGF_LINK_POLICY, 0x03),   
HCI_OPCODE_HCI_EXIT_SNIFF_MODE = HCI_OPCODE (OGF_LINK_POLICY, 0x04),   
HCI_O