CC2642 HCI接口使用

已于 2023-05-21 16:51:14 修改
阅读量484 收藏 1
点赞数
分类专栏： CC2642 文章标签： CC2642
于 2023-05-01 23:08:57 首次发布
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/dear_Wally/article/details/130459905
版权

1、HCI支持接口如下

/*
** HCI Command Opcodes
*/

// Link Control Commands
/// @cond NODOC
#define HCI_DISCONNECT                                    0x0406    //!< opcode of @ref HCI_DisconnectCmd
/// @endcond //NODOC
#define HCI_READ_REMOTE_VERSION_INFO                      0x041D    //!< opcode of @ref HCI_ReadRemoteVersionInfoCmd

// Controller and Baseband Commands
#define HCI_SET_EVENT_MASK                                0x0C01    //!< opcode of @ref HCI_SetEventMaskCmd
#define HCI_RESET                                         0x0C03    //!< opcode of@ref HCI_ResetCmd
#define HCI_READ_TRANSMIT_POWER                           0x0C2D    //!< opcode of@ref HCI_ReadTransmitPowerLevelCmd
/// @cond NODOC
#define HCI_SET_CONTROLLER_TO_HOST_FLOW_CONTROL           0x0C31    //!< opcode of @ref HCI_SetControllerToHostFlowCtrlCmd
#define HCI_HOST_BUFFER_SIZE                              0x0C33    //!< opcode of @ref HCI_HostBufferSizeCmd
/// @endcond //NODOC
#define HCI_HOST_NUM_COMPLETED_PACKETS                    0x0C35    //!< opcode of @ref HCI_HostNumCompletedPktCmd
#define HCI_SET_EVENT_MASK_PAGE_2                         0x0C63    //!< opcode of @ref HCI_SetEventMaskPage2Cmd
#define HCI_READ_AUTH_PAYLOAD_TIMEOUT                     0x0C7B    //!< opcode of @ref HCI_ReadAuthPayloadTimeoutCmd
#define HCI_WRITE_AUTH_PAYLOAD_TIMEOUT                    0x0C7C    //!< opcode of @ref HCI_WriteAuthPayloadTimeoutCmd

// Information Parameters
#define HCI_READ_LOCAL_VERSION_INFO                       0x1001    //!< opcode of @ref HCI_ReadLocalVersionInfoCmd
#define HCI_READ_LOCAL_SUPPORTED_COMMANDS                 0x1002    //!< opcode of @ref HCI_ReadLocalSupportedCommandsCmd
#define HCI_READ_LOCAL_SUPPORTED_FEATURES                 0x1003    //!< opcode of @ref HCI_ReadLocalSupportedFeaturesCmd
#define HCI_READ_BDADDR                                   0x1009    //!< opcode of @ref HCI_ReadBDADDRCmd

// Status Parameters
#define HCI_READ_RSSI                                     0x1405    //!< opcode of @ref HCI_ReadRssiCmd

// LE Commands
// V4.0
#define HCI_LE_SET_EVENT_MASK                             0x2001    //!< opcode of @ref HCI_LE_SetEventMaskCmd
#define HCI_LE_READ_BUFFER_SIZE                           0x2002    //!< opcode of @ref HCI_LE_ReadBufSizeCmd
#define HCI_LE_READ_LOCAL_SUPPORTED_FEATURES              0x2003    //!< opcode of @ref HCI_LE_ReadLocalSupportedFeaturesCmd
/// @cond NODOC
#define HCI_LE_SET_RANDOM_ADDR                            0x2005    //!< opcode of @ref HCI_LE_SetRandomAddressCmd
#define HCI_LE_SET_ADV_PARAM                              0x2006    //!< opcode of @ref HCI_LE_SetAdvParamCmd
#define HCI_LE_READ_ADV_CHANNEL_TX_POWER                  0x2007    //!< opcode of @ref HCI_LE_ReadAdvChanTxPowerCmd
#define HCI_LE_SET_ADV_DATA                               0x2008    //!< opcode of @ref HCI_LE_SetAdvDataCmd
#define HCI_LE_SET_SCAN_RSP_DATA                          0x2009    //!< opcode of @ref HCI_LE_SetScanRspDataCmd
#define HCI_LE_SET_ADV_ENABLE                             0x200A    //!< opcode of @ref HCI_LE_SetAdvEnableCmd
#define HCI_LE_SET_SCAN_PARAM                             0x200B    //!< opcode of @ref HCI_LE_SetScanParamCmd
#define HCI_LE_SET_SCAN_ENABLE                            0x200C    //!< opcode of @ref HCI_LE_SetScanEnableCmd
#define HCI_LE_CREATE_CONNECTION                          0x200D    //!< opcode of @ref HCI_LE_CreateConnCmd
#define HCI_LE_CREATE_CONNECTION_CANCEL                   0x200E    //!< opcode of @ref HCI_LE_CreateConnCancelCmd
/// @endcond // NODOC
#define HCI_LE_READ_WHITE_LIST_SIZE                       0x200F    //!< opcode of @ref HCI_LE_ReadWhiteListSizeCmd
#define HCI_LE_CLEAR_WHITE_LIST                           0x2010    //!< opcode of @ref HCI_LE_ClearWhiteListCmd
#define HCI_LE_ADD_WHITE_LIST                             0x2011    //!< opcode of @ref HCI_LE_AddWhiteListCmd
#define HCI_LE_REMOVE_WHITE_LIST                          0x2012    //!< opcode of @ref HCI_LE_RemoveWhiteListCmd
/// @cond NODOC
#define HCI_LE_CONNECTION_UPDATE                          0x2013    //!< opcode of @ref HCI_LE_ConnUpdateCmd
/// @endcond // NODOC
#define HCI_LE_SET_HOST_CHANNEL_CLASSIFICATION            0x2014    //!< opcode of @ref HCI_LE_SetHostChanClassificationCmd
#define HCI_LE_READ_CHANNEL_MAP                           0x2015    //!< opcode of @ref HCI_LE_ReadChannelMapCmd
#define HCI_LE_READ_REMOTE_USED_FEATURES                  0x2016    //!< opcode of @ref HCI_LE_ReadRemoteUsedFeaturesCmd
#define HCI_LE_ENCRYPT                                    0x2017    //!< opcode of @ref HCI_LE_EncryptCmd
#define HCI_LE_RAND                                       0x2018    //!< opcode of @ref HCI_LE_RandCmd
/// @cond NODOC
#define HCI_LE_START_ENCRYPTION                           0x2019    //!< opcode of @ref HCI_LE_StartEncyptCmd
#define HCI_LE_LTK_REQ_REPLY                              0x201A    //!< opcode of @ref HCI_LE_LtkReqReplyCmd
#define HCI_LE_LTK_REQ_NEG_REPLY                          0x201B    //!< opcode of @ref HCI_LE_LtkReqNegReplyCmd
/// @endcond // NODOC
#define HCI_LE_READ_SUPPORTED_STATES                      0x201C    //!< opcode of @ref HCI_LE_ReadSupportedStatesCmd
#define HCI_LE_RECEIVER_TEST                              0x201D    //!< opcode of @ref HCI_LE_ReceiverTestCmd
#define HCI_LE_TRANSMITTER_TEST                           0x201E    //!< opcode of @ref HCI_LE_TransmitterTestCmd
#define HCI_LE_TEST_END                                   0x201F    //!< opcode of @ref HCI_LE_TestEndCmd
// V4.1
/// @cond NODOC
#define HCI_LE_REMOTE_CONN_PARAM_REQ_REPLY                0x2020    //!< opcode of @ref HCI_LE_RemoteConnParamReqReplyCmd
#define HCI_LE_REMOTE_CONN_PARAM_REQ_NEG_REPLY            0x2021    //!< opcode of @ref HCI_LE_RemoteConnParamReqNegReplyCmd
/// @endcond // NODOC
// V4.2
#define HCI_LE_SET_DATA_LENGTH                            0x2022    //!< opcode of @ref HCI_LE_SetDataLenCmd
#define HCI_LE_READ_SUGGESTED_DEFAULT_DATA_LENGTH         0x2023    //!< opcode of @ref HCI_LE_ReadSuggestedDefaultDataLenCmd
#define HCI_LE_WRITE_SUGGESTED_DEFAULT_DATA_LENGTH        0x2024    //!< opcode of @ref HCI_LE_WriteSuggestedDefaultDataLenCmd
/// @cond NODOC
#define HCI_LE_READ_LOCAL_P256_PUBLIC_KEY                 0x2025    //!< opcode of @ref HCI_LE_ReadLocalP256PublicKeyCmd
#define HCI_LE_GENERATE_DHKEY                             0x2026    //!< opcode of @ref HCI_LE_GenerateDHKeyCmd
/// @endcond // NODOC
#define HCI_LE_ADD_DEVICE_TO_RESOLVING_LIST               0x2027    //!< opcode of @ref HCI_LE_AddDeviceToResolvingListCmd
#define HCI_LE_REMOVE_DEVICE_FROM_RESOLVING_LIST          0x2028    //!< opcode of @ref HCI_LE_RemoveDeviceFromResolvingListCmd
#define HCI_LE_CLEAR_RESOLVING_LIST                       0x2029    //!< opcode of @ref HCI_LE_ClearResolvingListCmd
#define HCI_LE_READ_RESOLVING_LIST_SIZE                   0x202A    //!< opcode of @ref HCI_LE_ReadResolvingListSizeCmd
#define HCI_LE_READ_PEER_RESOLVABLE_ADDRESS               0x202B    //!< opcode of @ref HCI_LE_ReadPeerResolvableAddressCmd
#define HCI_LE_READ_LOCAL_RESOLVABLE_ADDRESS              0x202C    //!< opcode of @ref HCI_LE_ReadLocalResolvableAddressCmd
/// @cond NODOC
#define HCI_LE_SET_ADDRESS_RESOLUTION_ENABLE              0x202D    //!< opcode of @ref HCI_LE_SetAddressResolutionEnableCmd
/// @endcond // NODOC
#define HCI_LE_SET_RESOLVABLE_PRIVATE_ADDRESS_TIMEOUT     0x202E    //!< opcode of @ref HCI_LE_SetResolvablePrivateAddressTimeoutCmd
#define HCI_LE_READ_MAX_DATA_LENGTH                       0x202F    //!< opcode of @ref HCI_LE_ReadMaxDataLenCmd
#define HCI_LE_SET_PRIVACY_MODE                           0x204E    //!< opcode of @ref HCI_LE_SetPrivacyModeCmd
// V5.0
#define HCI_LE_READ_PHY                                   0x2030    //!< opcode of @ref HCI_LE_ReadPhyCmd
#define HCI_LE_SET_DEFAULT_PHY                            0x2031    //!< opcode of @ref HCI_LE_SetDefaultPhyCmd
#define HCI_LE_SET_PHY                                    0x2032    //!< opcode of @ref HCI_LE_SetPhyCmd
#define HCI_LE_ENHANCED_RECEIVER_TEST                     0x2033    //!< opcode of @ref HCI_LE_EnhancedRxTestCmd
#define HCI_LE_ENHANCED_TRANSMITTER_TEST                  0x2034    //!< opcode of @ref HCI_LE_EnhancedTxTestCmd
#define HCI_LE_READ_TX_POWER                              0x204B    //!< opcode of @ref HCI_LE_ReadTxPowerCmd
#define HCI_LE_READ_RF_PATH_COMPENSATION                  0x204C    //!< opcode of @ref HCI_LE_ReadRfPathCompCmd
#define HCI_LE_WRITE_RF_PATH_COMPENSATION                 0x204D    //!< opcode of @ref HCI_LE_WriteRfPathCompCmd
// @cond NODOC
#define HCI_LE_SET_ADV_SET_RANDOM_ADDRESS                 0x2035    //!< opcode of @ref HCI_LE_SetAdvSetRandAddrCmd
#define HCI_LE_SET_EXT_ADV_PARAMETERS                     0x2036    //!< opcode of @ref HCI_LE_SetExtAdvParamsCmd
#define HCI_LE_SET_EXT_ADV_DATA                           0x2037    //!< opcode of @ref HCI_LE_SetExtAdvDataCmd
#define HCI_LE_SET_EXT_SCAN_RESPONSE_DATA                 0x2038    //!< opcode of @ref HCI_LE_SetExtScanRspDataCmd
#define HCI_LE_SET_EXT_ADV_ENABLE                         0x2039    //!< opcode of @ref HCI_LE_SetExtAdvEnableCmd
#define HCI_LE_READ_MAX_ADV_DATA_LENGTH                   0x203A    //!< opcode of @ref HCI_LE_ReadMaxAdvDataLenCmd
#define HCI_LE_READ_NUM_SUPPORTED_ADV_SETS                0x203B    //!< opcode of @ref HCI_LE_ReadNumSupportedAdvSetsCmd
#define HCI_LE_REMOVE_ADV_SET                             0x203C    //!< opcode of @ref HCI_LE_RemoveAdvSetCmd
#define HCI_LE_CLEAR_ADV_SETS                             0x203D    //!< opcode of @ref HCI_LE_ClearAdvSetsCmd
#define HCI_LE_SET_PERIODIC_ADV_PARAMETERS                0x203E    //!< opcode of @ref HCI_LE_SetPeriodicAdvParamsCmd
#define HCI_LE_SET_PERIODIC_ADV_DATA                      0x203F    //!< opcode of @ref HCI_LE_SetPeriodicAdvDataCmd
#define HCI_LE_SET_PERIODIC_ADV_ENABLE                    0x2040    //!< opcode of @ref HCI_LE_SetPeriodicAdvEnableCmd
#define HCI_LE_SET_EXT_SCAN_PARAMETERS                    0x2041    //!< opcode of @ref LE_SetExtScanParams
#define HCI_LE_SET_EXT_SCAN_ENABLE                        0x2042    //!< opcode of @ref LE_SetExtScanEnable
#define HCI_LE_EXT_CREATE_CONN                            0x2043    //!< opcode of @ref LE_ExtCreateConn
#define HCI_LE_PERIODIC_ADV_CREATE_SYNC                   0x2044    //!< opcode of @ref HCI_LE_PeriodicAdvCreateSyncCmd
#define HCI_LE_PERIODIC_ADV_CREATE_SYNC_CANCEL            0x2045    //!< opcode of @ref HCI_LE_PeriodicAdvCreateSyncCancelCmd
#define HCI_LE_PERIODIC_ADV_TERMINATE_SYNC                0x2046    //!< opcode of @ref HCI_LE_PeriodicAdvTerminateSyncCmd
#define HCI_LE_ADD_DEVICE_TO_PERIODIC_ADV_LIST            0x2047    //!< opcode of @ref HCI_LE_AddDeviceToPeriodicAdvListCmd
#define HCI_LE_REMOVE_DEVICE_FROM_PERIODIC_ADV_LIST       0x2048    //!< opcode of @ref HCI_LE_RemoveDeviceFromPeriodicAdvListCmd
#define HCI_LE_CLEAR_PERIODIC_ADV_LIST                    0x2049    //!< opcode of @ref HCI_LE_ClearPeriodicAdvListCmd
#define HCI_LE_READ_PERIODIC_ADV_LIST_SIZE                0x204A    //!< opcode of @ref HCI_LE_ReadPeriodicAdvListSizeCmd
// @endcond // NODOC

// V5.1
// @cond NODOC
#define HCI_LE_ENHANCED_CTE_RECEIVER_TEST                 0x204F    //!< opcode of @ref HCI_LE_EnhancedCteRxTestCmd
#define HCI_LE_ENHANCED_CTE_TRANSMITTER_TEST              0x2050    //!< opcode of @ref HCI_LE_EnhancedCteTxTestCmd
#define HCI_LE_SET_CONNECTIONLESS_CTE_TRANSMIT_PARAMS     0x2051    //!< opcode of @ref HCI_LE_SetConnectionlessCteTransmitParamsCmd
#define HCI_LE_SET_CONNECTIONLESS_CTE_TRANSMIT_ENABLE     0x2052    //!< opcode of @ref HCI_LE_SetConnectionlessCteTransmitEnableCmd
#define HCI_LE_SET_CONNECTIONLESS_IQ_SAMPLING_ENABLE      0x2053    //!< opcode of @ref HCI_LE_SetConnectionlessIqSamplingEnableCmd
#define HCI_LE_SET_CONNECTION_CTE_RECEIVE_PARAMS          0x2054    //!< opcode of @ref HCI_LE_SetConnectionCteReceiveParams
#define HCI_LE_SET_CONNECTION_CTE_TRANSMIT_PARAMS         0x2055    //!< opcode of @ref HCI_LE_SetConnectionCteTransmitParams
#define HCI_LE_SET_CONNECTION_CTE_REQUEST_ENABLE          0x2056    //!< opcode of @ref HCI_LE_SetConnectionCteRequestEnable
#define HCI_LE_SET_CONNECTION_CTE_RESPONSE_ENABLE         0x2057    //!< opcode of @ref HCI_LE_SetConnectionCteResponseEnable
#define HCI_LE_READ_ANTENNA_INFORMATION                   0x2058    //!< opcode of @ref HCI_LE_ReadAntennaInformation
#define HCI_LE_SET_PERIODIC_ADV_RECEIVE_ENABLE            0x2059    //!< opcode of @ref HCI_LE_SetPeriodicAdvReceiveEnableCmd
// @endcond // NODOC

/// @endcond //NODOC
// LE Vendor Specific LL Extension Commands
#define HCI_EXT_SET_RX_GAIN                               0xFC00    //!< opcode of @ref HCI_EXT_SetRxGainCmd
#define HCI_EXT_SET_TX_POWER                              0xFC01    //!< opcode of @ref HCI_EXT_SetTxPowerCmd
#define HCI_EXT_ONE_PKT_PER_EVT                           0xFC02    //!< opcode of @ref HCI_EXT_OnePktPerEvtCmd
/// @cond CC254X
#define HCI_EXT_CLK_DIVIDE_ON_HALT                        0xFC03    //!< opcode of @ref HCI_EXT_ClkDivOnHaltCmd
#define HCI_EXT_DECLARE_NV_USAGE                          0xFC04    //!< opcode of @ref HCI_EXT_DeclareNvUsageCmd
/// @endcond // CC254X
#define HCI_EXT_DECRYPT                                   0xFC05    //!< opcode of @ref HCI_EXT_DecryptCmd
#define HCI_EXT_SET_LOCAL_SUPPORTED_FEATURES              0xFC06    //!< opcode of @ref HCI_EXT_SetLocalSupportedFeaturesCmd
#define HCI_EXT_SET_FAST_TX_RESP_TIME                     0xFC07    //!< opcode of @ref HCI_EXT_SetFastTxResponseTimeCmd
#define HCI_EXT_MODEM_TEST_TX                             0xFC08    //!< opcode of @ref HCI_EXT_ModemTestTxCmd
#define HCI_EXT_MODEM_HOP_TEST_TX                         0xFC09    //!< opcode of @ref HCI_EXT_ModemHopTestTxCmd
#define HCI_EXT_MODEM_TEST_RX                             0xFC0A    //!< opcode of @ref HCI_EXT_ModemTestRxCmd
#define HCI_EXT_END_MODEM_TEST                            0xFC0B    //!< opcode of @ref HCI_EXT_EndModemTestCmd
/// @cond NODOC
#define HCI_EXT_SET_BDADDR                                0xFC0C    //!< opcode of @ref HCI_EXT_SetBDADDRCmd
/// @endcond //NODOC
#define HCI_EXT_SET_SCA                                   0xFC0D    //!< opcode of @ref HCI_EXT_SetSCACmd
#define HCI_EXT_ENABLE_PTM                                0xFC0E    //!< opcode of @ref HCI_EXT_EnablePTMCmd
#define HCI_EXT_SET_FREQ_TUNE                             0xFC0F    //!< opcode of @ref HCI_EXT_SetFreqTuneCmd
#define HCI_EXT_SAVE_FREQ_TUNE                            0xFC10    //!< opcode of @ref HCI_EXT_SaveFreqTuneCmd
#define HCI_EXT_SET_MAX_DTM_TX_POWER                      0xFC11    //!< opcode of @ref HCI_EXT_SetMaxDtmTxPowerCmd
/// @cond CC254X
#define HCI_EXT_MAP_PM_IO_PORT                            0xFC12    //!< opcode of @ref HCI_EXT_MapPmIoPortCmd
/// @endcond //CC254X
#define HCI_EXT_DISCONNECT_IMMED                          0xFC13    //!< opcode of @ref HCI_EXT_DisconnectImmedCmd
#define HCI_EXT_PER                                       0xFC14    //!< opcode of @ref HCI_EXT_PacketErrorRateCmd
#define HCI_EXT_PER_BY_CHAN                               0xFC15    //!< opcode of @ref HCI_EXT_PERbyChanCmd
/// @cond CC254X
#define HCI_EXT_EXTEND_RF_RANGE                           0xFC16    //!< opcode of  @ref HCI_EXT_ExtendRfRangeCmd
/// @endcond // CC254X
/// @cond CC254X
#define HCI_EXT_HALT_DURING_RF                            0xFC19    //!< opcode of @ref HCI_EXT_HaltDuringRfCmd
/// @endcond // CC254X
#define HCI_EXT_OVERRIDE_SL                               0xFC1A    //!< opcode of @ref HCI_EXT_SetSlaveLatencyOverrideCmd
#define HCI_EXT_BUILD_REVISION                            0xFC1B    //!< opcode of @ref HCI_EXT_BuildRevisionCmd
/// @cond CC254X
#define HCI_EXT_DELAY_SLEEP                               0xFC1C    //!< opcode of @ref HCI_EXT_DelaySleepCmd
/// @endcond //CC254X
#define HCI_EXT_RESET_SYSTEM                              0xFC1D    //!< opcode of @ref HCI_EXT_ResetSystemCmd
/// @cond CC254X
#define HCI_EXT_OVERLAPPED_PROCESSING                     0xFC1E    //!< opcode of @ref HCI_EXT_OverlappedProcessingCmd
/// @endcond //CC254X
#define HCI_EXT_NUM_COMPLETED_PKTS_LIMIT                  0xFC1F    //!< opcode of @ref HCI_EXT_NumComplPktsLimitCmd
/// @cond NODOC
#define HCI_EXT_GET_CONNECTION_INFO                       0xFC20    //!< opcode of @ref HCI_EXT_GetConnInfoCmd
/// @endcond // NODOC
#define HCI_EXT_SET_MAX_DATA_LENGTH                       0xFC21    //!< opcode of @ref HCI_EXT_SetMaxDataLenCmd
#define HCI_EXT_SET_DTM_TX_PKT_CNT                        0xFC24    //!< opcode of @ref HCI_EXT_SetDtmTxPktCntCmd
/// @cond NODOC
#define HCI_EXT_READ_RAND_ADDR                            0xFC25    //!< opcode of @ref HCI_ReadRandAddrCmd
/// @endcond //NODOC
#define HCI_EXT_ENHANCED_MODEM_TEST_TX                    0xFC27    //!< opcode of @ref HCI_EXT_EnhancedModemTestTxCmd
#define HCI_EXT_ENHANCED_MODEM_HOP_TEST_TX                0xFC28    //!< opcode of @ref HCI_EXT_EnhancedModemHopTestTxCmd
#define HCI_EXT_ENHANCED_MODEM_TEST_RX                    0xFC29    //!< opcode of @ref HCI_EXT_EnhancedModemTestRxCmd
// @cond NODOC
#define HCI_EXT_SET_PIN_OUTPUT                            0xFC2A    //!< opcode of @ref HCI_SetPinOutputCmd
#define HCI_EXT_SET_LOCATIONING_ACCURACY                  0xFC2B    //!< opcode of @ref HCI_SetLocationingAccuracyCmd
#define HCI_EXT_GET_ACTIVE_CONNECTION_INFO                0xFC2C    //!< opcode of @ref HCI_EXT_GetActiveConnInfoCmd
#define HCI_EXT_COEX_ENABLE                               0xFC2E    //!< opcode of @ref HCI_EXT_CoexEnableCmd

#define HCI_EXT_LL_TEST_MODE                              0xFC70    //!< opcode of @ref HCI_EXT_LLTestModeCmd

#define HCI_EXT_LE_SET_EXT_ADV_DATA                       0xFC71    //!< opcode of @ref HCI_EXT_LE_SetExtAdvDataCmd
#define HCI_EXT_LE_SET_EXT_SCAN_RESPONSE_DATA             0xFC72    //!< opcode of @ref HCI_EXT_LE_SetExtScanRspDataCmd
#define HCI_EXT_LE_SET_EXT_VIRTUAL_ADV_ADDRESS            0xFC73    //!< opcode of @ref HCI_EXT_SetVirtualAdvAddrCmd
#define HCI_EXT_SET_SCAN_CHAN                             0xFC74    //!< opcode of @ref HCI_EXT_SetExtScanChannels
#define HCI_EXT_SET_QOS_PARAMETERS                        0xFC75    //!< opcode of @ref HCI_EXT_SetQOSParameters
#define HCI_EXT_SET_QOS_DEFAULT_PARAMETERS                0xFC76    //!< opcode of @ref HCI_EXT_SetQOSDefaultParameters
#define HCI_LE_MAKE_DISCOVERABLE_DONE                     0xFC77    //!< opcode of @ref HCI_LE_SetAdvStatus
#define HCI_LE_END_DISCOVERABLE_DONE                      0xFC78    //!< opcode of @ref HCI_LE_SetAdvStatus

// @endcond //NODOC


// LE Vendor Specific LL Extension Events
#define HCI_EXT_SET_RX_GAIN_EVENT                         0x0400    //!< event from @ref HCI_EXT_SetRxGainCmd
#define HCI_EXT_SET_TX_POWER_EVENT                        0x0401    //!< event from @ref HCI_EXT_SetTxPowerCmd
#define HCI_EXT_ONE_PKT_PER_EVT_EVENT                     0x0402    //!< event from @ref HCI_EXT_OnePktPerEvtCmd
/// @cond CC254X
#define HCI_EXT_CLK_DIVIDE_ON_HALT_EVENT                  0x0403    //!< event from @ref HCI_EXT_ClkDivOnHaltCmd
#define HCI_EXT_DECLARE_NV_USAGE_EVENT                    0x0404    //!< event from @ref HCI_EXT_DeclareNvUsageCmd
/// @endcond //CC254X
#define HCI_EXT_DECRYPT_EVENT                             0x0405    //!< event from @ref HCI_EXT_DecryptCmd
#define HCI_EXT_SET_LOCAL_SUPPORTED_FEATURES_EVENT        0x0406    //!< event from @ref HCI_EXT_SetLocalSupportedFeaturesCmd
#define HCI_EXT_SET_FAST_TX_RESP_TIME_EVENT               0x0407    //!< event from @ref HCI_EXT_SetFastTxResponseTimeCmd
#define HCI_EXT_MODEM_TEST_TX_EVENT                       0x0408    //!< event from @ref HCI_EXT_ModemTestTxCmd
#define HCI_EXT_MODEM_HOP_TEST_TX_EVENT                   0x0409    //!< event from @ref HCI_EXT_ModemHopTestTxCmd
#define HCI_EXT_MODEM_TEST_RX_EVENT                       0x040A    //!< event from @ref HCI_EXT_ModemTestRxCmd
#define HCI_EXT_END_MODEM_TEST_EVENT                      0x040B    //!< event from @ref HCI_EXT_EndModemTestCmd
/// @cond NODOC
#define HCI_EXT_SET_BDADDR_EVENT                          0x040C    //!< event from @ref HCI_EXT_SetBDADDRCmd
/// @endcond //NODOC
#define HCI_EXT_SET_SCA_EVENT                             0x040D    //!< event from @ref HCI_EXT_SetSCACmd
#define HCI_EXT_ENABLE_PTM_EVENT                          0x040E    //!< event from @ref HCI_EXT_EnablePTMCmd
#define HCI_EXT_SET_FREQ_TUNE_EVENT                       0x040F    //!< event from @ref HCI_EXT_SetFreqTuneCmd
#define HCI_EXT_SAVE_FREQ_TUNE_EVENT                      0x0410    //!< event from @ref HCI_EXT_SaveFreqTuneCmd
#define HCI_EXT_SET_MAX_DTM_TX_POWER_EVENT                0x0411    //!< event from @ref HCI_EXT_SetMaxDtmTxPowerCmd
/// @cond CC254X
#define HCI_EXT_MAP_PM_IO_PORT_EVENT                      0x0412    //!< event from @ref HCI_EXT_MapPmIoPortCmd
/// @endcond //CC254X
#define HCI_EXT_DISCONNECT_IMMED_EVENT                    0x0413    //!< event from @ref HCI_EXT_DisconnectImmedCmd
#define HCI_EXT_PER_EVENT                                 0x0414    //!< event from @ref HCI_EXT_PacketErrorRateCmd
#define HCI_EXT_PER_BY_CHAN_EVENT                         0x0415    //!< event from @ref HCI_EXT_PERbyChanCmd
/// @cond CC254X
#define HCI_EXT_EXTEND_RF_RANGE_EVENT                     0x0416    //!< event from @ref HCI_EXT_ExtendRfRangeCmd
/// @endcond //CC254X
/// @cond CC254X
#define HCI_EXT_HALT_DURING_RF_EVENT                      0x0419    //!< event from @ref HCI_EXT_HaltDuringRfCmd
#define HCI_EXT_OVERRIDE_SL_EVENT                         0x041A    //!< event from @ref HCI_EXT_SetSlaveLatencyOverrideCmd
/// @endcond //CC254X
#define HCI_EXT_BUILD_REVISION_EVENT                      0x041B    //!< event from @ref HCI_EXT_BuildRevisionCmd
/// @cond CC254X
#define HCI_EXT_DELAY_SLEEP_EVENT                         0x041C    //!< event from @ref HCI_EXT_DelaySleepCmd
/// @endcond //CC254X
#define HCI_EXT_RESET_SYSTEM_EVENT                        0x041D    //!< event from @ref HCI_EXT_ResetSystemCmd
/// @cond CC254X
#define HCI_EXT_OVERLAPPED_PROCESSING_EVENT               0x041E    //!< event from @ref HCI_EXT_OverlappedProcessingCmd
/// @endcond //CC254X
#define HCI_EXT_NUM_COMPLETED_PKTS_LIMIT_EVENT            0x041F    //!< event from @ref HCI_EXT_NumComplPktsLimitCmd
/// @cond NODOC
#define HCI_EXT_GET_CONNECTION_INFO_EVENT                 0x0420    //!< event from @ref HCI_EXT_GetConnInfoCmd
/// @endcond // NODOC
#define HCI_EXT_SET_MAX_DATA_LENGTH_EVENT                 0x0421    //!< event from @ref HCI_EXT_SetMaxDataLenCmd
#define HCI_EXT_SET_DTM_TX_PKT_CNT_EVENT                  0x0424    //!< event from @ref HCI_EXT_SetDtmTxPktCntCmd
/// @cond NODOC
#define HCI_EXT_READ_RAND_ADDR_EVENT                      0x0425    //!< event from @ref HCI_EXT_ReadRandAddrCmd
/// @endcond //NODOC
#define HCI_EXT_LE_ADV_EVENT                              0x0425    //!< Extended advertisement event
#define HCI_EXT_LE_SCAN_EVENT                             0x0426    //!< Extended Scanner event

#define HCI_EXT_ENHANCED_MODEM_TEST_TX_EVENT              0x0427    //!< event from @ref HCI_EXT_EnhancedModemTestTxCmd
#define HCI_EXT_ENHANCED_MODEM_HOP_TEST_TX_EVENT          0x0428    //!< event from @ref HCI_EXT_EnhancedModemHopTestTxCmd
#define HCI_EXT_ENHANCED_MODEM_TEST_RX_EVENT              0x0429    //!< event from @ref HCI_EXT_EnhancedModemTestRxCmd
// @cond NODOC
#define HCI_EXT_SET_PIN_OUTPUT_EVENT                      0x042A    //!< event from @ref HCI_EXT_SetPinOutputCmd
#define HCI_EXT_SET_LOCATIONING_ACCURACY_EVENT            0x042B    //!< event from @ref HCI_EXT_SetLocationingAccuracyCmd
#define HCI_EXT_GET_ACTIVE_CONNECTION_INFO_EVENT          0x042C    //!< event from @ref HCI_EXT_GetActiveConnInfoCmd
#define HCI_EXT_SET_VIRTUAL_ADV_ADDRESS_EVENT             0x042D    //!< event from @ref HCI_EXT_SetVirtualAdvAddrCmd
#define HCI_EXT_COEX_ENABLE_EVENT                         0x042E    //!< event from @ref HCI_EXT_CoexEnableCmd









/*
** HCI Event Codes
*/

// BT Events
#define HCI_DISCONNECTION_COMPLETE_EVENT_CODE             0x05      //!< event of type @ref hciEvt_DisconnComplete_t
#define HCI_ENCRYPTION_CHANGE_EVENT_CODE                  0x08      //!< event of type @ref hciEvt_EncryptChange_t
#define HCI_READ_REMOTE_INFO_COMPLETE_EVENT_CODE          0x0C      //!< event of type @ref hciPacket_t
#define HCI_COMMAND_COMPLETE_EVENT_CODE                   0x0E      //!< event of type @ref hciEvt_CmdComplete_t
#define HCI_COMMAND_STATUS_EVENT_CODE                     0x0F      //!< event of type @ref hciEvt_CommandStatus_t
#define HCI_BLE_HARDWARE_ERROR_EVENT_CODE                 0x10      //!< event of type @ref hciEvt_HardwareError_t
#define HCI_NUM_OF_COMPLETED_PACKETS_EVENT_CODE           0x13      //!< event of type @ref hciEvt_NumCompletedPkt_t
#define HCI_DATA_BUFFER_OVERFLOW_EVENT                    0x1A      //!< event of type @ref hciEvt_BufferOverflow_t
#define HCI_KEY_REFRESH_COMPLETE_EVENT_CODE               0x30      //!< event of type @ref hciPacket_t
#define HCI_APTO_EXPIRED_EVENT_CODE                       0x57      //!< event of type @ref hciEvt_AptoExpired_t

// LE Event Code (for LE Meta Events)
#define HCI_LE_EVENT_CODE                                 0x3E      //!< LE Event

// LE Meta Event Codes
#define HCI_BLE_CONNECTION_COMPLETE_EVENT                 0x01      //!< event of type @ref hciEvt_BLEConnComplete_t
#define HCI_BLE_ADV_REPORT_EVENT                          0x02      //!< event of type @ref hciEvt_DevInfo_t
#define HCI_BLE_CONN_UPDATE_COMPLETE_EVENT                0x03      //!< event of type @ref hciEvt_BLEConnUpdateComplete_t
#define HCI_BLE_READ_REMOTE_FEATURE_COMPLETE_EVENT        0x04      //!< event of type @ref hciEvt_BLEReadRemoteFeatureComplete_t
#define HCI_BLE_LTK_REQUESTED_EVENT                       0x05      //!< event of type @ref hciEvt_BLELTKReq_t
// V4.1
#define HCI_BLE_REMOTE_CONN_PARAM_REQUEST_EVENT           0x06      //!< event of type @ref hciEvt_BLERemoteConnParamReq_t
// V4.2
#define HCI_BLE_DATA_LENGTH_CHANGE_EVENT                  0x07      //!< event of type @ref hciEvt_BLEDataLengthChange_t
#define HCI_BLE_READ_LOCAL_P256_PUBLIC_KEY_COMPLETE_EVENT 0x08      //!< event of type @ref hciEvt_BLEReadP256PublicKeyComplete_t
#define HCI_BLE_GENERATE_DHKEY_COMPLETE_EVENT             0x09      //!< event of type @ref hciEvt_BLEGenDHKeyComplete_t
#define HCI_BLE_ENHANCED_CONNECTION_COMPLETE_EVENT        0x0A      //!< event of type @ref hciEvt_BLEEnhConnComplete_t
#define HCI_BLE_DIRECT_ADVERTISING_REPORT_EVENT           0x0B      //!< direct advertising report...not used
// V5.0
#define HCI_BLE_PHY_UPDATE_COMPLETE_EVENT                 0x0C      //!< event of type @ref hciEvt_BLEPhyUpdateComplete_t

#define HCI_BLE_EXTENDED_ADV_REPORT_EVENT                 0x0D      //!< Extended Adv Report
#define HCI_BLE_PERIODIC_ADV_SYNCH_ESTABLISHED_EVENT      0x0E      //!< Periodic Adv Synch Established
#define HCI_BLE_PERIODIC_ADV_REPORT_EVENT                 0x0F      //!< Periodic Adv Report
#define HCI_BLE_PERIODIC_ADV_SYNCH_LOST_EVENT             0x10      //!< Periodic Adv Synch Lost
#define HCI_BLE_SCAN_TIMEOUT_EVENT                        0x11      //!< Scan Timeout
#define HCI_BLE_ADV_SET_TERMINATED_EVENT                  0x12      //!< Adv Set Terminated
#define HCI_BLE_SCAN_REQUEST_RECEIVED_EVENT               0x13      //!< Scan Request Received
#define HCI_BLE_CHANNEL_SELECTION_ALGORITHM_EVENT         0x14      //!< Channel Selection Algorithm
#define HCI_BLE_CONNECTIONLESS_IQ_REPORT_EVENT            0x15      //!< CTE sample connectionless report
#define HCI_BLE_CONNECTION_IQ_REPORT_EVENT                0x16      //!< CTE sample connection report
#define HCI_BLE_CTE_REQUEST_FAILED_EVENT                  0x17      //!< CTE sample failed

#define HCI_BLE_BLE_LOG_STRINGS_MAX 0x17
extern char *BLEEventCode_BleLogStrings[];

// VS Meta Event Codes - Texas Instruments Inc specific!
#define HCI_BLE_SCAN_REQ_REPORT_EVENT                     0x80      //!< event of type @ref hciEvt_BLEScanReqReport_t
#define HCI_BLE_EXT_CONNECTION_IQ_REPORT_EVENT            0x81      //!< event of type @ref hciEvt_BLEExtCteConnectionIqReport_t
#define HCI_BLE_CHANNEL_MAP_UPDATE_EVENT                  0x82      //!< event of type @ref hciEvt_BLEChanMapUpdate_t
#define HCI_BLE_CONN_UPDATE_REJECT_EVENT                  0x83      //!< event of type @ref hciEvt_BLEConnUpdateComplete_t
#define HCI_BLE_EXT_CONNECTIONLESS_IQ_REPORT_EVENT        0x84      //!< event of type @ref hciEvt_BLEExtCteConnectionlessIqReport_t

#define HCI_TEST_EVENT_CODE                               0xFE      //!< test event code use for cte test
#define HCI_VE_EVENT_CODE                                 0xFF      //!< event of type @ref hciEvt_VSCmdComplete_t

2、如何使用接口

1、下面以HCI_LE_ReadTxPowerCmd接口为例，读取发射功率

2、通过全局搜索SDK工程，HCI_LE_ReadTxPowerCmd这个接口对应的事件是HCI_LE_READ_TX_POWER，这个事件是在HCI_COMMAND_COMPLETE_EVENT_CODE（hciEvt_CmdComplete_t）里面

/**
 * Read the minimum and maximum supported Tx Power.
 *
 * @par Corresponding Events
 * @ref hciEvt_CmdComplete_t with cmdOpcode @ref HCI_LE_READ_TX_POWER
 *
 * @return @ref HCI_SUCCESS
 */
extern hciStatus_t HCI_LE_ReadTxPowerCmd( void );

3、触发事件HCI_COMMAND_COMPLETE_EVENT_CODE->HCI_LE_READ_TX_POWER

static uint8_t SimplePeripheral_processStackMsg(ICall_Hdr *pMsg)
{
  // Always dealloc pMsg unless set otherwise
  uint8_t safeToDealloc = TRUE;

  switch (pMsg->event)
  {
    case HCI_GAP_EVENT_EVENT:
    {
      // Process HCI message
      switch(pMsg->status)
      {
        // Process HCI Command Complete Events here
        case HCI_COMMAND_COMPLETE_EVENT_CODE:
        {
          SimplePeripheral_processCmdCompleteEvt((hciEvt_CmdComplete_t *) pMsg);
        }break;
      }

    }break;
  }

  return (safeToDealloc);
}

static void SimplePeripheral_processCmdCompleteEvt(hciEvt_CmdComplete_t *pMsg)
{
  switch (pMsg->cmdOpcode)
  {
    case HCI_LE_READ_TX_POWER:
    {
      u_printf("HCI_LE_READ_TX_POWER\r\n");    

      // 0: Status
      // 1: Minimum Tx Power
      // 2: Maximum Tx Power
      u_printf_hex((char *)pMsg->pReturnParam,3);
    }break;
  }
}

4、通过查看HCI_LE_READ_TX_POWER事件发送源码，可以知道返回的数据格式

hciStatus_t HCI_LE_ReadTxPowerCmd( void )
{
  // 0: Status
  // 1: Minimum Tx Power
  // 2: Maximum Tx Power
  uint8 rtnParam[3];

  rtnParam[0] = MAP_LE_ReadTxPowerCmd( (int8 *)&rtnParam[1],
                                       (int8 *)&rtnParam[2] );

  MAP_HCI_CommandCompleteEvent( HCI_LE_READ_TX_POWER,
                                sizeof(rtnParam),
                                rtnParam );

  return( HCI_SUCCESS );
}

dear_Wally
关注
  • 0
    点赞
  • 踩
  • 1
    收藏
    觉得还不错? 一键收藏
  • 打赏
    打赏
  • 0
    评论
专栏目录
CC2642R 蓝牙MCU芯片的学习
m0_63737690的博客
06-03 4508
CC2642R 蓝牙MCU芯片是TI公司的一款芯片，本篇文章将总结这款芯片的性能和外围电路等，小白总结，如有错误，欢迎讨论。目录一、芯片引脚详细介绍二、特征及其参数三、典型外围电路四、应用引脚图如下：本图中粗体部分为具有高驱动能力的引脚：Pin 10, DIO_5 ，Pin 11, DIO_6 ，Pin 12, DIO_7 ，Pin 24, JTAG_TMSC ，Pin 26, DIO_16 ，Pin 27, DIO_17图中用斜体标识的I/O引脚具有模拟功能:Pin 36, DIO_23，Pin 37,
CC2642入手实操
yyw_0429的博客
11-16 5611
为迎合蓝牙5的快速发展，TI推出了一款基于ARM Cotex-M4内核的BLE5 蓝牙单片机—CC26x2.不过现在芯片还在还没有量产，在TI官网买了几片样片，并参照TI的开发板画了个板子，实测可以连接手机。 先简单介绍一下BLE5，在2016年BLE5协议诞生，像apple已经在iPhone8及以后的ihpone中使用BLE5，据小道消息还未上市的air pods将采用BLE5.那么BLE5相比...
[IAR][CC2642R1] IDE安装和环境搭建，CC2642的环境配置
jianqiang.xue
05-08 1250
回到这个工具，点browse按钮选择已生成在桌面的ActivationInfo.txt文件：C:\Users\dpg\Desktop\ActivationInfo.txt，在安装包中找到IAR REG支持.rar解压，如图所示，得到IAR算号注册生成工具，双击License Generator.exe运行。将生成的码复制到软件界面，选择断网，（我们整个激活是离线激活，所以一定要断网）点击下一步。如图所示，浏览到桌面，选择到文件ActivationInfo.txt，然后点下一步。默认安装，一直下一步即可。
第一部分：HCI协议（五）HCI Command flow control的具体实现
sui1005316018的博客
07-19 766
五、Command flow control的具体实现： 1、上电，host端发送HCI reset command之后，只能发送1个HCI comamnd包，等待接收到command complete或者command status event以后再继续下面的操作 2、接收到的command complete或者command status event里面包含一个参数是Num HCI Command Packets（用来表示当前Controller允许Host发送的最大command包数），Contr
蓝牙HCI协议
热门推荐
本地服务器
03-15 1万+
HCI 层位于蓝牙高层协议和低层协议之间，提供了对基带控制器和链路管理器的命令以及访问蓝牙硬件的统一接口,它是我们实现自己的蓝牙设备要接触的第一个蓝牙协议,起着承上启下的作用。 HCI通过包的方式来传送数据、命令和事件的，所有在主机和主机控制器之间的通信都以包的形式进行。包括每个命令的返回参数都通过特定的事件包来传输。HCI有数据、命令和事件三种包，其中数据包是双向的，命令包只能从主机发往主机控制
CC2642 读取和设置FEATURES
dear_Wally的博客
05-01 836
3、通过这个接口的源码可以知道，调用这个接口之后，都会执行HCI_COMMAND_STATUS_EVENT_CODE->HCI_LE_READ_REMOTE_USED_FEATURES事件，结果固定是成功。1、调用HCI_LE_ReadLocalSupportedFeaturesCmd，这个接口对应的事件是HCI_LE_READ_LOCAL_SUPPORTED_FEATURES，这个事件是在HCI_COMMAND_COMPLETE_EVENT_CODE（hciEvt_CmdComplete_t）里面。
蓝牙HCI 部分Command，Event
qq_44840245的博客
07-03 2389
蓝牙HCI部分Command与Event
CC2642研究之控制SPI Nand FLASH和EEPROM
yyw_0429的博客
11-26 3616
接上篇博客，测试蓝牙例程通过后，接下来实现利用CC2642控制板上的SPI接口NAND Flash和EEPROM。 软件：simplelink_cc26x2_sdk_2_30_00_34。 工具：Win10 64位PC，CCS8.2 一、TI SPI接口例程介绍 TI为CC2642开发提供了蓝牙协议栈，当然也包括外设的驱动，协议栈功能非常全面，涉及到了所有CC2642的资源。本文主要利用spim...
【资源共享】CC2640之新手常见问题集
feilusia的博客
11-04 5468
本文集合了香瓜整理的CC2640的新手常见问题，不断更新
ESP32 VHCI架构传统蓝牙设置scan mode，让设备能被搜索到
朝气蓬勃
04-23 2606
零. 声明 本专栏文章我们会以连载的方式持续更新，本专栏计划更新内容如下： 第一篇:ESP-IDF基本介绍，主要会涉及模组，芯片，开发板的介绍，环境搭建，程序编译下载，启动流程等一些基本的操作，让你对ESP-IDF开发有一个总体的认识，比我们后续学习打下基础！ 第二篇:ESP32-IDF外设驱动介绍，主要会根据esp-idf现有的driver，提供各个外设的驱动，比如LED,OLED,SPI LCD,TOUCH,红外,Codec ic等等，在这一篇中，我们不仅仅来做外设驱动，还会对常用的外设总线
BLE-CC2640之添加自定义服务
wo_wuhao
11-19 2884
BLE-CC2640之添加自定义服务
CC2640 的连接参数更新过程
Life_Maze的博客
08-02 710
CC2640R2F 连接参数更新
Life_Maze的博客
04-02 1070
-----------------------------------------------------------------simple_peripheral.c  （初始化）// After the connection is formed, the peripheral waits until the central// device asks for its preferred con...
第六章 CC2640的时钟API函数的解释及应用
lrlv5的博客
03-17 5140
时钟实例函数可以在一定计时完成后被重新调用。时钟实例既是一次性的也是周期性的。一旦创建，就立刻执行。或者配制成进过一段的延时之后才开始的。他们能够在任何时候被禁止。所有的时钟例子都可以被执行当他们在软件中断溢出时。 最小分辨率是RTOS时钟周期被设置在RTOS配置文件中。 /* 10 us tick period */ Clock.tickPeriod = 10; 每次计时，均来至于RT
CC2640 广播数据构成分析
lrlv5的博客
01-13 4975
第二章 CC2640广播数据构成 第一步：将SimpleBLEPeripheral例程烧录到蓝牙中然后就开启广播之旅了。。。。。。。。。 用Packet Sniffer 抓包  1        2        3           4                5                           6                      7      
TI RTOS系统在CC2642上的应用
yyw_0429的博客
01-02 3464
        TI针对自家处理器设计了RTOS实时操作系统，适用于TI的众多处理器例如蓝牙芯片CC26XX、MSP43X和多核DSP等等。由于之前在开发c6678时使用过RTOS，所以现在在CC2642上使用就顺畅的多。接下来进入正题，TI RTOS系统在CC2642上使用的介绍。 一、TI RTOS简介         TI 的RTOS实时操作系统原来名称为sys/bios，所以看到TI中...
蓝牙解析(part5):BLE的广播通信
Do what you want
12-29 9931
大家都知道，相比传统蓝牙，蓝牙低功耗（BLE）最大的突破就是加大了对广播通信（Advertising）的支持和利用。本文将从技术的角度，分析和理解BLE协议中有关广播通信的定义和实现。
CC2640 MAC地址理解、使用和更改
lrlv5的博客
01-13 5243
第一章CC2640 MAC地址使用、理解和更改 说明：一般BLE在出厂时都有唯一的标识地址，俗称MAC地址，其在广播时，随设备名一起广播出去。请看用Packet Sniffer抓包结果： ADVA ：0X0AD0AD0AD0AD 就是MAC 地址。 可以修改,对应代码如下： static void SimpleBLEPeripheral_init(void) {   // ***
HCI opcode
a1028732302的专栏
12-07 1008
蓝牙hci指令opcode，ogf，ocf组成
cc2540 hci tester命令
最新发布
08-08
HCI（Host Controller Interface）Tester命令用于测试和配置CC2540芯片的功能和性能。 HCI Tester命令主要包含以下几个方面的功能： 1. 收发数据测试：可以通过HCI Tester命令向CC2540芯片发送指定的数据包，并...

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包

打赏作者

dear_Wally

你的鼓励将是我创作的最大动力

¥1 ¥2 ¥4 ¥6 ¥10 ¥20
扫码支付：¥1
获取中
扫码支付

您的余额不足，请更换扫码支付或充值

打赏作者

实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值